Elo TouchSystems 6.3.0 инструкция обслуживания

Elo Touch Solutions Multi-touch Driver Package User Manual Elo Touch Solution s 1033 McCarthy Blvd Milpitas, CA 95035 Package Version: 6.3.0 Release Date: July 17, 2014 Supported OS: W ind ows XP W ind ows 7 W ind ows 8 / 8.1 W ind ows Server 2012 / 2012R2 Supported Touch Technologies: iTouch (SAW ) iTouch Plus (SA W ) pCap Optical Int elliT ouch ([...]

1.1 Installation • Double click on EloSetup .exe • Accept the installation ag ree ment and proceed wi th the insta llation pro cess. 1.2 Uninstallatio n • Launch the Control Pan el and choos e Progra ms and Features. • Select to re move “Elo Tou ch Solutions 6.3.0.x”. 1.3 Silent Installa tion • Open the command line shell as an admini[...]

3. Configuration Program: EloConfig.exe This is the c onfiguration tool for t he Elo Multi-Touch driv ers. The set up program will launch t he tool at the end of the ins tallation. This program will be runnin g in t he background and will launch when t he user starts it from the Wi ndow’ s Cont rol Panel, or manually execut e it from t he desktop[...]

The Elo calibration tool is used to calibrate touch recognition on supported Elo t ouch screen monitors. After touching all 3 targets, the screen will show "Accept " and "Retry" buttons. The us er can t hen t est the calibration accuracy before sele ct ing either “Accept” (saving calibra tion dat a) or “Retry” (r e-doing[...]

Launching “Touch Screen Properties” wi ll display various properties of each connected ( and supported) El o touch screen suc h as Monitor Resolution, Co ntroller Serial Number, Controller Firmware Version, etc. In addition to this information, users will be given the ability to “D isable Touch” and “Restore def ault calibrat ion”. Also[...]

To en able CEA, click on the "Select D efault" butt on and specify the desired parameters. The position of CEA ma y be manipulated for all edges at once b y means of t he “Increase/ Decrease CEA Area” b uttons, or individ ually b y means of the a rrows along eac h edge. Additional ly, CEA for part icular edges may be disabled by unche[...]

section [ Calibration], c hange the value " DriverCalibration" to 1. User does not need t o reinstall t he package for this change t o take effec t. 3.4 Common Setti ngs Configure shared touch screen settings s uch as “ Beep on Touch”, “Touch M ode”, hiding t he cursor during calibratio n, and spanned displa y mode. 3.4.1 Beep on [...]

3.4.3 Hide curs or duri ng calibratio n Enabling the set ting will hide the mous e cursor when running the calibrat ion utility. Disabling the sett ing will display the mous e cursor when running t he calibration ut ility. Note: The user must click “Apply” f or a ll changes to take eff ect. Clicking “Close” without c licking “Apply” wil[...]

touch zone. • The user can drag t his second box t o any touch screen and adjust it s size and posit ion. • It may be spec ified in t he “EloTouchZones” dialog box whether t ouch wil l be enabled “ inside” or “out side” the zone. If the user chooses to h ave touch enabled “ inside zone”, touch will only work within each defined [...]

4. Instructions for Window s 7 Emb edded The fo llowing notes are intended as a guide f or enabling mult i-touch func tionality with W indows 7 Embedded. 4.1 Use Ta p.exe to generat e a PMQ f ile including all hardware information of the target system. 4.2 Start ICE ( Image Configuration Editor), cr eate an ANSW ER file, and import the PMQ f ile. 4[...]

monitor needs to be power cycled, t hen re-calibrated to r estore normal t ouch. If powe r c ycling the monitor is not workin g, the utilti y EloCalMgr.exe (located in the t arget installation folder) can be us ed to re set the controller. 6. Appendix 6.1 Installation/ Uninstallation from Device Ma nager 6.1.1 Installation • Open W indows Device [...]

and se parated b y a s pace; No H EX or C HARs. The 8 numbers repres ent t he 8-byte Smartset Command. 6.2.2 Smar tset Comman d Limitati ons: There is no limit to the number of Smartset comman ds that can be sent. For example, if 10 Smartset C ommands (10 lines) are specified under the [Smarts et Commands] section, all 10 Smartset Commands will be [...]

Release 4.0.2 • Serial driver: New calibration is not taking eff ect. • Serial driver: After reboot, previous calibration is not applied. • Serial driver: Pre-install either legacy serial driver or multi-touc h serial driver (not both). Release 4.0.3 • Correct t he multi touc h mode in Lumio/Opt ical monitor. • Added W indows 8 su pport. [...]

• Correct t he pCap firmware ve rsion shown in the propert y page. • Support both new and old f irmware fo r Optical t ouch monitors. • Provide opt ions to limit nu mber of to uches (please see Readm e). • IDS improveme nts: slow response, incorrec t initial touch status, incorrec t power status report. Release 6.2.1 • Check t he 2521 con[...]