Dolmar HT-2556 D, HT-2576 E инструкция обслуживания

Instruction Manual Important: Read this instruction manual carefully before putting the hedge trimmer into operation and strictly observe the safety regulations! Keep this instruction manual! HT -2556 D http://www .dolmar .com HT -2576 E[...]

2 T able of contents Page Conformity Declaration ...................................................... 2 Packaging ............................................................................ 2 Delivery inventory .............................................................. 3 Symbols ...............................................................[...]

3 4 Delivery inventory 1. Hedge trimmer HT -2576 E (depending on order) 2. Hedge trimmer HT -2556 D (depending on order) 3. Knife guard 4. Universal wrench 5. Instruction Manual (not shown) In case one of the parts listed should not be included in the delivery inventory , please consult your sales agent. Symbols Y ou will notice the following symbo[...]

4 5 1 4 3 2 SAFETY PRECAUTIONS General precautions - In order to ensure safe operation, the operator must read this instruction manual to familiarize him or herself with the operation of the hedge trimmer . Users insufciently informed will endanger themselves as well as others due to improper handling. - Lend the hedge tr[...]

5 6 7 10 9 8 - Fuels can contain substances similar to solvents. Eyes and skin should not come in contact with mineral oil products. Always wear protective gloves when refuelling. Frequently clean and change protective clothes. Do not breathe in fuel vapors. Inhalation of fuel vapours can be hazardous to your health. - Do not spill fuel or oil. Whe[...]

6 - After use, clean the trimmer , in particular the cutter . Oil the cutter lightly and put on the blade guard. - Emtpy the fual tank completely before long-term storage or shipping the trimmer . Maintenance - Always switch off the trimmer and pull off the spark plug cap before doing any maintenance! - Pay special attention to the proper condi - t[...]

7 1 Rear grip 2 Safety cutoff 3 Throttle lever 4 ON/OFF (I/O) switch 5 Starter grip 6 Fuel tank cap Stroke volume cm 3 24,5 24,5 Max. power at speed kW / rpm 0,88 / 7.000 0,88 / 7.000 Idling speed / Max. engine speed with cutter rpm 2.600 / 9.800 2.600 / 9.800 Clutch engagement speed rpm 3.600 3.600 Sound pressure level at the workplace L pA av per[...]

8 + A Gasoline It is not wise to add more engine oil than specied to ensure safe operation. This will only result in a higher production of combus-tion residues which will pollute the environment and clog the exhaust channel in the cylinder as well as the mufer . In addition, fuel consumption will rise and perform- ance will decrease. The Sto[...]

9 B C Refuelling FOLLOW THE SAFETY PRECAUTIONS! Be careful and cautious when handling fuels. Refuel only with the engine switched off and cooled down! Thoroughly clean the area around the caps, to prevent dirt from getting into the fuel tank. Unscrew the tank cap and ll the tank with fuel mixture until itre[...]

10 D E 7 Cold start: Move the ON/OFF ( I / O ) switch ( 2 ) to position “I” . T urn the starting lever ( 6 ) to the ST ART position. Press the fuel pump ( 5 ) several (7-10) times to supply fuel to the carburetor . Assume the starting position (see above under Starting posi- tion ). Pull the starter cable by the grip ( 3 ) out slowly until you [...]

1 1 1 2 3 4 Tips on trimming hedges The procedure described here can be used very often and makes working easier . If a hedge has to be cut back very substantially , it should be trimmed in two passes. The trapezoidal form shown prevents the lower portion of the hedge from thinning out due to lack of light. - First cut the hedge to the desired heig[...]

12 A B STOP C STOP Cleaning and care Caution: Be especially careful when cleaning and caring for the cutter (injury hazard!). Never touch the cutter with bare hands. Always wear protective gloves! Regularly check the cutter for damage and clean it with a sui- table brush or cloth. If after extended use cutting performance is no longer satis- factor[...]

13 D E F STOP Checking the mufer bolts / cleaning the exhaust outlet Caution: Do not tighten the mufer bolts when the engine is hot! The mufer bolts ( 6 ) are directly accessible so they can be checked for tightness. If loose, hand-tighten (caution: do not over-tighten). Regularly clean the exhaust outlet ( 7 ) with a suitable too[...]

14 G Replacing the suction head The felt lter ( 8 ) of the suction head can become clogged. It is recommended to replace the suction head once every three months in order to ensure unimpeded fuel ow to the carburetor . T o remove the suction head for replacement, pull it out through the tank [...]

15 Service, spare parts and guarantee Workshop service The maintenanceand repair of modernhedge trimmers aswell as all safetydevices require qualiedtechnical training and aspecial workshop equipped with special tools and testing devices. All work not described in this Instruction Man[...]

16 Pos. DOLMAR-No. Qty . Denomination 1 377 601 400 1 T ank cap, cpl. 2 382 650 390 1 Suction head 3  374300401 1 Airlterinsert 4 381 014 981 1 Spark plug - 944 340 001 1 Screwdriver - 944 350 000 1 Grease gun Extract from the spare parts list Use only original DOLMAR parts. For repairs and replacement of other parts, see yo[...]

17 Notes[...]

18 Notes[...]

19 Notes[...]

Form: 995 701 252 (3.06 GB) Specicationssubjecttochangewithoutnotice DOLMAR GmbH Postfach 70 04 20 D-22004 Hamburg Germany http://www .dolmar .com[...]