Dimplex WRCPF-KIT инструкция обслуживания

Owner ’ s Manual Model WRCPF-KIT 72091 10100R03 IMPORT ANT SAFETY INFORMA TION: Always read this manual rst before attempting to install or use this device. For your safety , always comply with all warnings and safety instructions contained in this manual to prevent personal injury or property damage. T o view the full line of Dimplex products[...]

2 www .dimplex.com T able of Contents ! NOTE: Procedures and techniques that are considered important enough to emphasize. CAUTION: Procedures and techniques which, if not carefully followed, will result in damage to the equipment.  W ARNING: Procedures and techniques which, if not carefully followed, will expose the user to the risk of re, s[...]

3 W elcome & Congratulations Thank you and congratulations for choosing to purchase a W all Switch Remote Control Kit from Dimplex, the world leader in electric replaces. Please carefully read and save these instructions. CAUTION: Read all instructions and warnings carefully before starting installation. Failure to follow these instructions [...]

4 www .dimplex.com Product Overview The W all Switch Remote Control Kit is designed to work with the following Dimplex electric replaces: BF33STP • BF33DXP • BF39STP • BF39DXP • BF45DXP • BFSL33 • BLF50 • DF3033ST • DFG3033BLK • For the BF units, mentioned above, follow the Remote Receiver control installation instructions star[...]

5 Receiver Installation (BF units only) Open steel curtain (remove 1. glass doors if applicable). Remove two (2) screws on l og 2. grate and remove log grate (Figure 1). Locate and remove the two (2) 4. screws on the manual control bracket (Figure 3). Remove the bracket. Locate and depress the 5. mounting tabs on the plug connector and remove the m[...]

6 www .dimplex.com Locate the plastic 9-pin plug 6. in the bottom corner of the replace where the manual controls were plugged in to. Insert the plug connector from 7. the remote control bracket (Figure 4) into plastic plug inside the replace. ledge (Figure 2) and the logs are resting against the partially reective glass. Replace log grate[...]

7 W all Control Installation ! NOTE: All electrical w iring must comply with all national and local electrical codes and regulations. Always use a qualied and licensed electrician should you have any questions or concerns for all wiring work. ! NOTE: The W all Switch Remote Control is made to t standard Decora style faceplates. Due to materia[...]

8 www .dimplex.com Figure 5 Outer Housing Controller 2. Release the Controller from its Outer Housing by pushing the front face into the Outer Housing until you hear a click. This will release the push- lock latches and allow the Controller to be removed from the Outer Housing (Figure 5). 4. Replace the battery compartment cover . 5. Reinsert the C[...]

9 W all Control Installation to complete the installation and to blend the installation in with your choice of decor . Hard Wired Power Supplied Installation Before starting this installation, it is helpful to initialize the W all Switch Remote Control with your rebox (see Initialization section). Y ou should have the following items ready and p[...]

10 www .dimplex.com W all Control Installation 1. Unpack the W all Switch Remote Control and all hardware from its package. 2. Release the Controller from its Outer Housing by pushing the front face into the Outer Housing until you hear a click. This will release the push- lock latches and allow the Controller to be removed from the Outer Housing ([...]

11 W all Control Installation Figure 12 Controller Outer Housing Figure 13 Locking Screw Option (Figure 14) T o prevent tampering, damage, and theft, it is suggested to install the locking screws. Once installed, the locking screws will prevent the Controller from being released from the Outer Housing without being removed rst from the device bo[...]

12 www .dimplex.com W all Control Installation Figure 15 Ensure each of the two Controller lead wires are connected to separate Low V oltage 24V~ only wires. Low V oltage 24V~ power source ONL Y Controller wire leads Figure 16 Flat Head Screws (supplied)[...]

13 ! NOTE: Wire leads are not polarized due to the nature of this device. 9. Coil excess wiring to the back of the device box and insert the Controller and Outer Housing int o t he d evi ce box (Fi gur e 16 ). Fasten with two supplied at head screws. 10. Attach your choice of Decora style faceplate (not supplied) to complete the installation and[...]

14 www .dimplex.com Initialization After installation, locate the section which applies to your specic model of replace and follow the steps for remote control initialization and if required, re-initialization. Refer to your replace's owner's manual to locate manual or other controls as needed. BF Models Using the Included Receiv[...]

15 Initialization DF3033ST and DFG3033 Models 1. Ensure that power is supplied through main service panel. 2. Ensure the Main On/Off Switch located in the switch box on the replace in the upper right hand corner is in the On position (Figure 19A) . A B C Figure 19 DF3033ST / DFG3033 Manual controls 3. Set the 3 Position Manual Control (Figure 19[...]

16 www .dimplex.com Operation A. On Button Pressing this button toggles sequentially through the three levels of the replace. Pressing once activates Level 1 - ame effect only , twice activates Level 2 - ame effect and Purire™, three times activates Level 3 - ame effect, Purire™ and heat. B. Off Button Pressing this button at [...]

17 Operation W all Switch Remote Control 1 3 5 2 4 6 7 9 11 8 10 12 13 14 1. Room T emperature 2. Set T emperature 3. Flame Effect 4. Purire™ 5. Heat Off Indicator 6. Function Lock Indicator 7. RF Code Function Indicator 8. Set T emperature Down 9. Set T emperature Up 10. Flame Off 1 1. Flame On 12. Purire™Off 13. Purire™[...]

18 www .dimplex.com Operation 1. Room T emperature Displays current ambient temperature in the room. 2. Set T emperature Displays and controls the heater to the temperature at which the thermostat is currently set to. Press 8 to lower the thermostat and press 9 to raise the thermostat. Pressing both 8 and 9 together will toggle between Celsius and [...]

19 Operation 7. RF Code Function and Change Procedure In the event that the W all Switch Remote Control does not work properly with the receiver due to interference from additional wireless signals, this function will allow the RF code to be changed. T o enable this function, press 9 and 12 together . “ COD ” will appear on the display for v[...]

20 www .dimplex.com W arranty This Dimplex W all Switch Remote Control is warranted against defects in workmanship and materials for two years from date of sale. This warranty does not apply to damage from accident, misuse, or alteration, nor where the connected voltage is more that 5 % above the nameplate voltage, nor to equipment improperly insta[...]