Dell D10D инструкция обслуживания

Installation Guide Dell ® Wyse D Class Conversion to WES7 Wyse USB Firmware T ool TM Release 1.20 . 0 .1 Products: D10D , D50D , D90DW Issue: 040914 PN: 883887-38L Rev . A[...]

Copyright Notices © 2014 , Dell Inc. All Rights Reserved. This manual and the software and firmware described in it are copyrighted. Y ou may not reproduce, transmit, transcribe, store in a retrieval system, or translate into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual[...]

Contents 1 Introduction 1 Kit Contents 1 Kit Warranty 2 Overview 2 Dell T echnical Support 2 Related Documentation and Services 2 Dell Online Community 2 2 Installing D Class Flash 3 Requirements 3 Procedures 3 3 Installing WES7 Firmware 7 Requirements 7 Procedures 8 T roubleshooting 13 USB Keys - T r oubleshooting Boot Issues 13 SanDisk Cruiser Fl[...]

iv Contents This page intentionally b lank.[...]

1 Introduction This guide provides step-by-step instructions to use Wyse USB Firmware T ool to convert the following Wyse D class thin clients to WES7: • D10D (with minimum 2 GB RAM) • D50D (with minimum 2 GB RAM) • D90DW (with minimum 4 GB RAM) CAUTION : WES7 firmware r equires D class thin clients to have a minimum of 8 GB Flash and 4 GB RA[...]

2 Chapter 1 Kit Warranty The warranty on the hardware component of this kit assumes the remaining months of warranty of the thin client in which it is installed, or for 90 days, whichever is greater . Installation of this kit will not void the factory warranty, however the user will be responsible for damage due to improper installation. Overview T[...]

2 Installing D Class Flash This chapter contains information for users of Wyse D class thin clients who must install new flash. Requirements • Small Phillips screwdriver WARNING : Flash modules may be susceptible to damage by Electro- Static Discharge (ESD). All industry-standard cautions should be followed to avoid ESD . Before you remove or ins[...]

4 Chapter 2 4. Place your thumbs on the top surface of the opposite end where the three screws were removed. With a continuous motion, push firmly downward and towards the back panel (pushing down unlatches the hooks under the cover). The cover will shift approximate 1/4 inch to hang over the back panel. (a) Grasp the overhanging cover edge and rai[...]

Installing D Class Flash 5 Figure 5 Main board and Flash module 7. Remove the existing flash module. Locate the flash module and use the Phillips Screwdriver to remove its retaining scr ew as shown in Figure 6. Lift the flash module out of the socket. Figure 6 Removing the existing flash module 8. Install the new flash module in the reverse order o[...]

6 Chapter 2 This page intentionally b lank.[...]

3 Installing WES7 Firmware This chapter includes the requirements and procedur es you need to install and use Wyse USB Firmware T ool to update your thin client to WES7 firmware. TIP : The purpose of the USB Firmware T ool is to configure a bootable USB key f or device firmware. In the following procedures, you will cr eate a configured USB key con[...]

8 Chapter 3 Procedures IMPORT ANT : Complete the following procedures as an administrator (administrator privileges are required). Step 1: Copy the D Class WES7 Conversion Image Folder (on the DVD- ROM) to Y our Local Hard Drive Navigate to the D Class WES7 Conversion Image folder (contained on the Conversion Software Assembly DVD- ROM) and copy it[...]

Installing WES7 Firmware 9 Figure 8 Configuration options 3. Select the Configure the USB key to Copy/Pull or to Update/Push firmware option, and then click Next to open the Select the Configuration dialog box. Figure 9 Update firmware options - Windows Embedded Standard 7 4. Select the Windows Embedded Standard 7 operating system (OS) type option.[...]

10 Chapter 3 Figure 10 Browse for image file 8. Click Browse . Figure 11 Browse to select commandsXml.xml 9. Navigate to the D Class WES7 Conversion Image folder (on your hard drive) that contains the commandsXml.xml file (this is the location you selected in "Step 1: Copy the D Class WES7 Conversion Image Folder (on the DVD- ROM) to Y our Loc[...]

Installing WES7 Firmware 11 11 . Select the USB key onto which you want the configurations (you can use Refresh as needed to recognize an inserted USB key), and then click Next . The pr ogress bars show the overall (formatting and configuration) progress and task progr ess. CAUTION : DO NO T interrupt the formatting and configuration process. All p[...]

12 Chapter 3 Step 5: V erifying Thin Client Operation After the thin client displays the WES7 desktop, you can verify the V ersion and that your general client information is correct. 1. On the General tab of the Wyse Client Information window ( Start > All Programs > Wyse Client Information ), verify the following: • V ersion is 9. 05 Buil[...]

Installing WES7 Firmware 13 Step 7: Obtain a Firmware Update After converting your thin clients, obtain any available firmware update at http://www. wyse.com/serviceandsupport/support/downloads.asp . WARNING : Use of the Software on more than one device requires that you first purchase from Dell additional copies of, or licenses to, the Softwar e. [...]

Installation Guide Dell ® Wyse D Class Conversion to WES7 Issue: 040914 Written and published by: Dell Inc., April 2014 Created using FrameMaker ® and Acr obat ®[...]