DCS Flat Panel TV инструкция обслуживания

Installation Guide Fly your Flat P anel TV Mount Cantilever Series Every effort has been made to provide accurate and error-free assembly and installation. DCS Mount disclaims liability for any difficulties arising from the interpretation of information contained in these instructions. If DCS Mount products are used for purposes other than their or[...]

Illustration for hardware kit LP -80 Flat P anel Cantilever Mount Installation Instructions z 80 lb. Maximum weight capacity z VESA 75/100 compliant z Cantilever arm mount for large LCD and small plasma panels z Allows maximum flexibility for insta lling and viewin g displays. z Cantilever arm provides full extension and 180 ¡ of la[...]

This flat panel can tilever will hold larger LCD monitor 30 in ches and over . It will also hold smaller plasma monitors up to 32 inches. First deter mine if your mo nitor is VESA sta ndard co mpliant, refer to th e monitor’s users manual. VESA is a standard mounting hole patter n (see image 1). The LP-80 Flat P anel Cantilever c an attac h direc[...]

5. All o f the screws are pro perly torqued to specifica tion when the unit is assembled at the factor y and should not need an fur ther initial a djustments. Ho wever , due to the v ariety in size of differen t monitors, MI NOR adjustmen t may be required to optimize th e tension n eeded for ease of mo vement. Be sure that your monitor is suppor t[...]

Mounting the W all Plate Mounting to W ooden Stud 1. Deter mine the location wher e you want t he display mounted on the wall. 2. USE stud finder to l ocate an d mark the c enter of the two studs. 3. R emove P -150 from box. R emove the P A -4260 Adaptor plate from the Mounting Head, an d set the four 3/ 8-16 bu tton head screws asi de for later . [...]

Mounting Cantilever Assembly 1. Impor tant: for the display to be centered over the wall plat e when the cantilever ar m is folded, t he ar m will need to be offset by approximately 4”(10.1c m) from the desired center positio n of the screen. T o do this, fir st not whe re the de sired cent er of scree n position i nterse cts the wall plate , and[...]

Configuring the P A -4260 adaptor plate (Install ation instructi ons) P A-4260 Universal Plasma TV Adaptor Installation Instructions z F ully adjustable design fits most l arge flat panel displays z Includes complete hardware kit z Quick mount capability with P -150 z Durable grey or black powder coat finish Check the Hare W are Kit aft[...]

Set P A-4260 width The P A -4260 is capable of handling a wide ran ge of landed inser t widths. Me asure the hor izontal dist ance betw een mounti ng lands on your display , and set the w idth of the Mounting Rails as shown, Standard R ange: 38 1/2”(98 cm) to 15 3/4”(40 cm) Standard Confi guration F or standard ra nge co nfiguratio ns, loo sen [...]

Mount P A-4260 to Display Hardware Selection a. Cons ult the suppl ied Hardware Cross R eference list. b. Select the mo unting ha rdware for you r display . Attach P A-4260 to Display a. P osition th e P A -4260 over back o f display . b. Thread moun ting screws thro ugh sq uare washers and spacers (i f required), as shown. c. Thread mounting screw[...]

Mounting the display 1. Locate th e set of four 3/8”-16 bu tton head c ap screws remov ed at the beginning of the installat ion. 2. Thread two of th e screws appro ximately a 1/4”(0.6cm) into th e upper set of PEM nuts on t he adaptor plat e, as shown 3. With the help of an assi stant, carefully lif t the display and hang i t onto the P -150 by[...]

V er tica l Tilt Fu n c t io n – raising and lowerin g the screen edge to improve v iewing angle/picture quali ty . Operation – Loos en tilt tension screws with suppl ied 3/16” Hex wrenc h as shown. Adjust display for desired t ilt angle. Re-tighte n tension scre ws. CAUTION : It is important to try to maintain even torque on each of the 4 sc[...]

HARDWARE CROSS REFERENCE LIST 3DJH Manufacturer Model Spacer Part ID Fastener dia x length Part ID AKIRA EPM 420A/B NONE N/A 5mm x 15 J AKIRA EPM 600 NONE N/A 8mm x 20* N AKAI PDP4290 NONE N/A M8 x 35 P B & Q BEOVISION 4 3/4 x 3/8 D 8mm x 35 P BENQ PDP46W1 NONE N/A 6mm x 35 L DAWOO DP425M NONE N/A 5mm x 15 J DAWOO DSP4210 NONE N/A 5mm [...]

HARDWARE CROSS REFERENCE LIST 3DJH Manufacturer Model Spacer Part ID Fastener dia x length Part ID HITACHI 50HDT50 NONE N/A 6mm x 16 L HITACHI 50HDT55 NONE N/A 6mm x 16 L HITACHI CMP4201 NONE N/A 6mm x 16 L HITACHI CMP4202 NONE N/A 6mm x 16 L HITACHI CMP5000WXV NONE N/A 6mm x 16 L HITACHI 32HDT20 NONE N/A 6mm x 16 L HITACHI 42HDT20 NONE N/[...]

HARDWARE CROSS REFERENCE LIST 3DJH Manufacturer Model Spacer Part ID Fastener dia x length Part ID NEC 42MP3 NONE N/A 5mm x 15 J NEC 42MP4 NONE N/A 5mm x 15 J NEC 42VP4A NONE N/A 5mm x 15 J NEC 42VP4D NONE N/A 5mm x 15 J NEC 50XM3A NONE N/A 5mm x 15 J NEC 50MP2 NONE N/A 5mm x 15 J NEC 61MP1 5mm x 15 J NEC PD-42XM1 NONE N/A 5mm x 15 J NEC P[...]

HARDWARE CROSS REFERENCE LIST 3DJH Manufacturer Model Spacer Part ID Fastener dia x length Part ID PIONEER PRO800 NONE N/A 8mm x 20* N PIONEER PDP-433CMX NONE N/A 8mm x 20* N PIONEER PDP-4330HD NONE N/A 8mm x 20* N PIONEER PRO1000 NONE N/A 8mm x 20* N PIONEER PDP-502MX NONE N/A 8mm x 20* N PIONEER PDP-5030HD NONE N/A 8mm x 20* N PIONEER PD[...]

HARDWARE CROSS REFERENCE LIST 3DJH Manufacturer Model Spacer Part ID Fastener dia x length Part ID SAMSUNG HPN6339 3/4 x 3/8 D 8mm x 35 P SAMSUNG HPM6315 8mm x 35 P SAMSUNG PPM42S3 3/4 x 3/8 D 8mm x 35 P SAMSUNG PPM50H3 3/4 x 3/8 D 8mm x 35 P SAMSUNG PPM63H3 8mm x 35 P SAMSUNG SPL-4225K 3/4 x 3/8 D 8mm x 35 P SAMSUNG SPN-4235 3/4 x 3/8 D 8[...]

HARDWARE CROSS REFERENCE LIST 3DJH Manufacturer Model Spacer Part ID Fastener dia x length Part ID YAMAHA PDM-1 3/4 x 3/8 D 8mm x 35 P ZENITH P40B24 NONE N/A 5mm x 15 J ZENITH P42W22B NONE N/A 5mm x 15 J ZENITH P42W26 NONE N/A 5mm x 15 J ZENITH P42W22BH NONE N/A 5mm x 15 J ZENITH P60W26 NONE N/A 8mm x 20 N ZENITH P60W26H 8mm x 20 N ZENITH [...]