D-Link IEEE802.3af инструкция обслуживания

D-Link DES-1008PA 8-Port 10/100Mbps IEEE802.3af Switch User’s Guide[...]

FCC Warning This equipment has been tested and fou nd to comply with the regulations f or a Class B digit al device, purs uant to Part 15 of the FCC Rules. These limits are designed to provide reasonable p rotection against harmful interference when the equipment is operated in a commercial environm ent. This eq uipment ge nerates, us es, and can r[...]

UL Warning a) Elevated Operating Ambient Temp erature- If installed in a closed or multi-unit rack assembly, the operating ambient temperatu re of the rack environment may be greater th an room ambient. Therefore, consideration should be given to installing the equipmen t in an environm ent compatibl e with the manufacturer' s maxi mum rated a[...]

TABLE OF CONTENTS About This Guide ................................................................................. 1 Purpose ............................................................................................ 1 Terms/Usage .................................................................................... 1 Introduction ................[...]

ABOUT THIS GUIDE Congratulations on you r purchase of the D-Link DES-1008 PA, an 8- Port 10/100Mbps Fast Ethernet Sw itch with 4-Port PoE. This Switch integrates 100M bps Fast Ethernet and 10Mbps Ethern et network capabilities in a highly flexible pa ckage. Port-1 to Port-4 on th e switch support Power over Ethernet (PoE ), meaning it will automati[...]

INTRODUCTION This chapter describes the features of the D-Link DES-1008P A Fast Ethernet PoE Switch and some backgr ound information abou t Ethernet/Fast Ethernet, Switching an d Power over Ether net technology. Fast Ethernet Technology The growing importance of LANs and the increasing complexity o f desktop com puting a pplications are fueling the[...]

Switching Technology Another a pproach to p ushing beyond the l imits of Ethernet t echnology is the devel opment of s witching technology . A swit ch bridges Ethernet packet s at the MAC address level of the Ethernet protocol transmitting a mong connect ed Ethernet or Fast Et hernet LAN segments. Switching is a cost-effective way of increasing the[...]

Power over Ethernet (PoE) Power over Ethernet (PoE) integrates power and data onto one single cabling infrastructure, elim inating the need to have AC power available at all locations. Power and Data is integrated on to the same cable, supporting category 5/5e up to 100 Meters. PoE will provide power to PoE compatible devices, such as IP telephones[...]

UNPACKING AND INSTALLATION This chapter provides unpack ing and installation info rmation for the Switch. Unpacking Open the shippi ng cartons of th e Switch and carefully unpack its contents. The carton should co ntain the following items: One DES-1008PA One AC power adapter Four rubbe r feet to be used fo r shock cus hioning User’s Guide If any[...]

Connecting Network Cable The Switch s upport 8 10/ 100Mbps Ethernet po rts and Port 1 ~ port 4 are PoE Enabled ports, these PoE port will automatically activate when a compatible terminal is identified. The Switch will supply power throu gh the Ethernet port t o the connect ed PoE powered de vice (PD). For legacy devices that are not co mpatible, t[...]

IDENTIFYING EXTERNAL COMP ONENTS This chapter describes th e front panel, rear panel, and LED ind icators of the Switch. Front Panel The figure below shows the fron t panels of the Switch. Figure 1. Front panel LED Indicator: Comprehensive LED indicators display th e status of the switch and the network (see the L ED Indicators chapter below). Rear[...]

These ports support network speed s of either 10Mbps or 100Mbps, and can operate in half- and full- duplex transfer modes. These ports also support automatic MDI/MDIX crossover det ection, whi ch gives the Switch true, “plug and play” capabilities. Just connect any n etwork cable between the Switch and the device, and The Switch will automatica[...]

UNDERSTANDING LED INDICATORS The front panel LEDs provide s instant status feedback , and helps monitor an d troubl eshoot wh en needed. Figure 3. LED indicators of the Sw itch System LED PWR: (Powe r Indicator ) On : Power On Off : Power Off PoE status LEDs (Port 1 ~ Port 4) PoE Status: Green : When the PoE powered device (PD) is connected and the[...]

PoE MAX Green When the power output to PDs is over 42W. No additional PDs can be powered. Off When the system is using less than 42W Blinking Green After the power output to PDs has reached or exceeded the maximum power budget, if the user unplugged certain PDs and made the system power left over 10W, the PoE MAX will blink 2 minutes. Ethernet port[...]

For example: There are POE PDs c onnected to the POE Switch a nd the total power consumption is 48 watts. The system will reserve 4 watts for a buffer and the POE MAX LED will light up. Once there is another POE PD inserted, the system will not provide power to the additional POE PD. Priority: This fu nction will help protect the system when the sy[...]

TECHNICAL SPECIFICATIONS General Standards IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3x Full Duplex Flow Control IEEE 802.3af Power over Ethernet Protocol CSMA/CD Data Transfer Rate Ethernet: 10Mbps (half duplex), 20Mbps (full-duplex) Fast Ethernet: 100Mbps (hal f duplex), 200Mbps (full-duplex) Topology Star Network[...]

Performance RAM Buffer: 96K bytes per device Filtering Address Table: 1K entries per device Packet Filtering/Forward ing Rate: 10Mbps Ethernet: 14,880/pps 100Mbps Fast Ethernet: 148,800/pps MAC Address Learning : Automatic update Transmits Method: Store-and-forwa rd 13[...]