Cresta DTX600 инструкция обслуживания

DTX600 WEA THERST A TION USER MANUAL Thank you for purchasing this device, Please read the operating instructions carefully to familarize yourself with the features and modes of operation before using the instrument. Package Contents Carefully unpack and remove the contents: • 1x weather station main unit • 1x stainless steel mast • 1x thermo[...]

• Batter ies : 2 x AA, LR 06 1.5V Installation • Installing the Batteries • Open the main unit battery cover located at the back of the unit and insert 2XAA batteries into the battery compartment and close the battery cover . • Pull away the shower proof casing of the thermo-hrgro sensor to reveal the 2 sockets.( for the wind sensor and rai[...]

• First insert the batteries of main unit, then insert the batteries of the outdoor sensor in 3 minutes after the main unit is powered on, to assure of the sensor data received well. In case of the outdoor sensor data received failure, pls press ALARM key for more than 3 seconds to synchronize the RF signal. • Every time the batteries are repla[...]

3. Mounting the rain sensor to the second plastic bracket: there are vertical engraved lines at the bottom edge of the round cover and the sensor part, you only need adjust the two line into one position, then turn clockwise, the rain sensor part will be connected well, then fix them with 4 screws onto the plastic bracket ( don’t use only 2 screw[...]

Note : please don’t put in or take off the plug very of fen,or put the plug outside in the air so long time to avoid any damage of the plug , if so, there will be bad connection. 5. Mounting all the sensors onto the stainless steel mast and fix the whole parts at outdoor open area :(note: please make sure all the cables are connected well into th[...]

LCD overview 1. Weather Forecast 2. Living space humidity 3. Indoor humidity trend 4. Indoor low battery 5. Rainfall 6. Air Pressure 7. Wind direction 8. Date 9. Wind speed 10. Month 1 1. Day of week 12. Moon Phase 13. Dual alarm 14. Time 15. RCC symbol 16. Summer time 17. Outdoor low battery 18. Outdoor humidity 19. Outdoor humidity trend 20. Indo[...]

23. RF symbol 24. Indoor temperature alert 25. Outdoor temperature trend 26. Indoor temperature 27. Indoor temperature trend A=MODE B= + C=- D= ALARM E= ALERT F=SNOOZE/LIGHT Initial Operation • After inserting the batteries, the main unit will connect with the outdoor sensor by RF signal. The RF signal symbol at the out area will flash. • This [...]

• The clock automatically changes from set-up mode to time display mode if no keys are pressed for 20 seconds. • Explanation for the time zone display: Y ou can manually adjust the clock to the time zone of a country (up to 1500km distance to Frankfurt/Main) where the clock receives the DCF signal but where the actual time differs from the time[...]

• Press “ALERT” for more than 3 seconds, the upper limit of inside temperature is flashing, use “ + “ and “ - “ to set the maximum alert temperature. • Press “ALERT “ , the lower limit of inside temperature is flashing, use “ + “ and “ - “ to set the minimum alert temperature. • Press “ALERT” , the upper limit of o[...]

Illumination • Press the key “ SNOOZE/LIGHT “ to activate the display illumination for 8 seconds. Moon phase display The weather station uses saved data to show the moon phase A B C D E F G H A: New moon B: increasing cr escent C: First half D: increasing 3/4 E: Full moon F: decr easing 3/4 G: Last half H: decreasing cr escent Living space hu[...]

• Press “ + “ , “ - “ for more than 3 seconds to enter or quit the Radio controlled signal reception • The clock synchronizes with the DCF radio signal automatically and daily from AM 1:00 to 3:00 to correct potential time deviations each hour . If the synchronization is unsuccessful (“radio tower“ symbol disappears), a further sync[...]