Craftsman 315.11196 инструкция обслуживания

Owner's Manual CRAFTSMAN + Variable Speed / Reversible 318 in. CORDLESS DRILL-DRIVER Model No. 315.111960 Save this manual for future reference -A CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product. Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA ® 972000-493 12-97[...]

• Warranty ......................................................................................................................................................... 2 • Introduction and Product Specifications ......................................................................................................... 2 • Rules For Safe Operation [...]

The purpose of safety symbols Is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they g!ve are not substitutes for proper accident prevention measures. SYMBO[...]

RULES FOR SAFE OPERATION (Continued) • NEVER USE IN AN EXPLOSIVE ATMO- SPHERE. Normal sparking of the motor could ignite flammable liquids, gases, or fumes. KEEP HANDLES DRY, CLEAN, AND FREE • FROM OIL AND GREASE. Always use a clean cloth when cleaning. Never use brake fluids, • gasoline, petroleum-based products or any strong solvents to cle[...]

RULES FORSAFE OPERATION (Contlnued). An extension cord should not be used Unless, absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure: a. That pins on plug of extension cord are the same number, size and shape as those of plug on charger. b. That extension[...]

The following recommended accessories are currently available at Sears Retail Stores. • 6-Pc. Extra Length Magnite Power Bit Set • 30-Pc. Power Scrawddver/Nutddver Set and Case • 17-Pc. Power Screwddver/Nutddver Set and Case • High Speed Bits ...... 3/8 inch Max. • Keylese Chuck (Item No. 20988) ,_ WARNING:. The use of attachments or acce[...]

WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. ,_ WARNING: Do not allow familiarity with your drill-driver to make you careless. Remember that a careless fraction of a second is sufficient to inf[...]

SWITCH See Figure 2. To tum your drill ON, depress the switch tdgger. To tum it OFF, release the switch trigger. CENTER POSmON (LOCK) SELECTOR SWITCH TRIGGER Fig. 2 VARIABLE SPEED This tool has a variable speed switch that delivers higher speed and torque with increased trigger pressure. Speed is controlled by the amount of switch trigger depressio[...]

TO INSTALL BATTERY PACK • Lock switch trigger on your drill by placing the direction of rotation selector in center position. See Figure 3. • Place battery pack in your drill. Align raised rib inside drill with groove on battery pack. See Figure 4. BATI'ERY t PACK TO REMOVE BATTERY PACK • Lock switch trigger on your drill by placing the [...]

INSTALLING BITS See Figure 6. Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 3. Open or close chuck jaws to a point where the opening is slightly larger than the bit size you intend to use. Also, raise the front of your drill slightly to keep the bit from falling out of the chuck jaws. • Inser[...]

BIT STORAGE See Figure 8. When not in use, bits provided with your drill can be placed in the storage area located on the bottom of your ddll as shown in figure 8. LEVEL DRILLING See Figure 10. A convenient new feature provided with your drill is a level, It is recessed in the motor housing on top of your ddlL It can be used to keep ddll bits level[...]

_1= WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. DRILLING See Figure 11. When ddlling hard smooth surfaces use a center punch to mark desired hole location. This will prevent the ddll bit from [...]

CHUCK REMOVAL(co_Inued) • Open chuck jaws and remove allen wrench. Remove the chuck screw by turning it in a clock- wise direction. See Figure 13. Note: The screw has left hand threads. Fig. 13 • Insert allen wrench in chuck and tighten chuck jaws securely. Tap sharply with a mallet in a countemlockwise direction. This will loosen chuck on the [...]

BA'n'ERIES " Your drill's battery pack is equipped with 6 nickel- cadmium rechargeable batteries. Length of service from each charging will depend on the type of work you are doing. The batteries in this tool have been designed to provide maximum trouble free life. However, like all batteries, they will eventually wear out. Do n[...]

CRAFTSMAN 3/8 in. CORDLESS DRILL-DRIVER MODEL NO. 315.111960 _-- I The model number will be found on a plate attached to the motor housing. Always mention the | I model number in all correspondence regarding your 3/8 in. CORDLESS DRILL-DRIVER or when I ordering repair parts. SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS 1 2 3 4 5 6 7 S 11 KEY PART [...]

For the repair or replacement parts you need delivered directly to your home Call 7 am - 7 pro, 7 days a week 1-800-366-PART (1-800-366-7278) For repairservice Call24 hours a day, 7 days a week 1-800-4-REPAIR (1-800-473-7247) For the location of a Sears Parts and Repair Center in your area Call 24 hours a day, 7 days a week 1-800-488-1 222 mmmmmm T[...]