Craftsman 247.797853 инструкция обслуживания

I MODELNOS. 247.797852 247.797853 Caution: Readand Follow All SafetyRules and instructions Before Operating This Equipment 5 HORSEPOWER 3 CUTTUNG STAGE MULCHUNG AND BAGGING CHBPPER-SHREDDER Assembly Operation Maintenance Service and Adjustment Repair Parts SEARS, ROEBUCK ANDCO., Chicago, IL 60684 U.S.A.[...]

SAFETY RULES WARNING: TO REDUCE THE POTENTIAL FOR ANY INJURY, COMPLY WITH THE FOLLOWING SAFETY INSTRUCTIONS. FAILURE TO COMPLY WITH THE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. TRAINING e Read this owner's manual carefully in its entirety before attempting to assemble or operate this machine Be com- pletely familiar with the corrtrols and t[...]

CONGRATULATIONS on your purchase of a Sears Craftsman Chipper-Shredder It has been designed, engi- neered and manufactured to give you the best possible dependability and performance Should you experience any problem you cannot easily rem- edy, please contact your nearest Sears Service Center/ Department. We have competent, well4rained technicians [...]

TABLE OF CONTENTS SAFETY RULES .............................................................. 2 PRODUCT SPECIFICATIONS ............................................ 3 CUSTOMER RESPONSIBILITIES .................................. 3 WARRANTY .......................................................................... 3 INDEX .............................[...]

m r._i7 _=: FIGURE 1. ASSEMBLY INSTRUCTnONS Flat ---_/t_ Washer [ _ ) ] 5/16" I.D. HeX Lock ut 5/16-18 Thread Hex Bolt • ,,----5/16-18 x 8-3/8" Long IMPORTANT: This unit is shipped WITHOUT GASO- LINE or OIL After assembly, see operation section of this manual for proper fuel and engine oil recommen- dations. NOTE: To determine right and[...]

Hex Nut ,. Knob J FIGURE 2, Stop Washer / FIGURE 3. Hopper Pivot Door ASSEMBLE THIS TRUSS SCREW AND NUT FIRST Release" Bar FIGURE 4. FIGURE 5. Bolt Chute Deflector / / Release Bar 8-3/8" Long Flat Washer Hex Lock Nut Guide Assembly HOW TO SET-UP YOUR CHIPPER-SHREDDER MAKE CERTAIN THE SPARK PLUG] WIRE IS DISCONNECTED AND MOVED / AWAY F[...]

e To attach the bag, place the opening of the bag over the chute deflector so it completely covers the chute opening. Depress the plunger on the draw- string, and pull on the drawstring until the bag is tight around the chute opening Release plunger to lock it into position, See figure 5, OPERATION KNOW YOUR CHIPPER-SHREDDER READ THIS OWNER'S [...]

BEFORE STARTING GAS AND OIL FILL-UP NOTE: ENGINE IS SHIPPED WITHOUT OIL FILL CRANKCASE WITH OIL BEFORE STARTING. BE VERY CAREFUL NOT TO ALLOW DIRT TO ENTER THE ENGINE WHEN CHECKING OR ADDING OIL OR FUEL Recommended SAE Viscosity Grades <llllll' 00!1o'w -%l !, 'T,,t _I_L_I. !1[I -20 ° 0 ° 32 ° 60 ° 80 ° 100 ° TEMPERATURE RANG[...]

e Pull rope with a rapid, continuous, full arm stroke, Keep a firm grip on start handle Let rope rewind slowly Do not let starter handle snap back against starter e Repeat preceding two instructions until engine fires When engine starts, move choke lever on engine halfway between CHOKE and RUN NOTE: If engine does not fire after three attempts, mov[...]

No 1/2" Diameter FIGURE 12. e To lower the hopper assembly, use one hand to grasp the handle at the top of the hopper assembly and lift slightly, Pull up on the release bar, and lower the hopper assembly to the ground Release the bar'. See figure 13. Hopper Assembly e Bulky material, such as stalks or heavy branches, up to 3" in diam[...]

When engine is drained of all oil, replace drain plug securely_ e Refill with fresh oil Above 32 °, use oil labeled SAE 30 or 10W30 Below 32 °, use oil labeled 5W20 Capacity is approximately 1-1/4 pints Refer to "Gas and Oil Fill-Up" on page 8 e Replace dipstick. AIR CLEANER The air cleaner prevents damaging dirt, dust, etc, from enteri[...]

STORAGE NEVER STORE YOUR CHIPPER- _SHREDDER INDOORS OR IN AN EN- CLOSED, POORLY VENTILATED AREA IF GASOLINE REMAINS IN THE TANK. FUMES MAY REACH AN OPEN FLAME, SPARK OR PILOT' LIGHT FROM A FUR- NACE, WATER HEATER, CLOTHES DRYER, CIGARETTE, ETC. To prevent engine damage if chipper-shredder is not used for more than 30 days, follow the steps bel[...]

SERVKCE & ADJUSTMENT WARNING: ALWAYS STOP ENGINE AND DISCONNECT SPARK PLUG WIRE AND MOVE IT AWAY FROM SPARK I PLUG BEFORE PERFORMING ANY ADJUSTMENTS OR REPA RS. REMOVING THE FLAIL SCREEN If the discharge area becomes clogged, remove the flail screen and clean area as follows e Stop the engine, make certain the chipper-shredder has come to a com[...]

Pi Sharp of Torque Wrenctl Allen Screws e When reassembling the blade, tighten to between 550 and 650 inch pounds, or lacking torque wrench, tighten securely FLAILS The flails, located inside the housing, may be reversed when they become dull It is suggested that this procedure be performed by your nearest Sears Service Department CARBURETOR ADJUST[...]

• Test the engine by using the chipper-shredder If engine tends to stall or die out, it usually indicates that the mixture is slightly lean and it may be nec- essary to open ( _ ) the needle valve slightly to provide a richer mixture This richer mixture may cause a slight unevenness in idling Throttle Idle Speed Stop Adjusting Screw ENGINE SPEED [...]

TROUBLE SHOO'rING PROBLEM POSSIBLE CAUSE(S) CORRECTIVE ACTION Engine fails to start e Fuel tank empty, or stale fuel e • Spark plug wire disconnected e e Faulty spark plug e Loss of power; operation erratic Engine overheats Too much vibration Unit does not discharge Rate of discharge slows considerably or composition of discharged material c[...]

SEARS CRAFTSMAN 5 H.P. CHIPPER-SHREDDER MODEL NOS. 247.797852 Repair Parts 247.797853 57 11 7 Model 59 22 35 36 17[...]

SEARS CRAFTSMAN 5 H.R CHIPPER-SHREDDER MODEL NOS. 247.797852 Repair Parts 247.797853 KEY NO, 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 22 23 24 25 26 27 28 29 3O 31 32 33 34 35 36 PART NO, 13431 742-0571 710-0818 714-0114 736-0217 736-0247 11459B 711-0564 711-0833A 711-0834 715-0249 736-0192 781-0484 681-0002 781-0490 710-1054 712-0411 736-011[...]

BRIGGS AND STRATTON 5 H.P. ENGINE MODEL NO. 130212-3250-01 Repair Parts 26 337 7 36 741 35 16 615 230 219 46 220 SEE REPAIR INS'TRt_TION MANUAL (_22 19[...]

BRIGGS AND STRATTON 5 H.P. ENGINE MODEL NO. 130212-3250-01 Repair Parts 3o5__ 24 71 305 655 73 37 *REQUIRES SPECIAL TOOLS TO INSTALL. SEE REPAIR INSTRUCTION MANUAL= 2O[...]

BRIGGS AND STRATTON 5 H.P. ENGINE MODEL NO. 130212-3250-01 Repair Parts 127A 96G { 124 969 9 414 153 208 153 1012 190 392 435 191 725 _ 209 527 529 11 526 21[...]

BRIGGS AND STRATTON 5 H.P. ENGINE MODEL NO. 130212-3250-01 Repair Parts KEY NO, 3 5 7 8 9 10 11 12 13 14 15 16 18 19 20 21 22 23 24 25 26 27 28 29 30 31 PART NO_ 395990 297565 299819 211542 *272157 294178 *27549 93394i 665781 *270080 *270125 *270126 94221 93369 91249 492926 493916 297603 298504 66768 94607 297229 222698 298904 298905 298906 298907 [...]

BRIGGS AND STRATTON 5 H.P. ENGINE MODEL NO. 130212-3250-01 Repair Parts KEY NO 216 2t9 220 222 223 224 227 230 256 284 298 299 304 305 306 307 308 333 335 337 346 356 358 363 373 383 392 394 414 432 433 434 435 441 467 523 524 525 526 527 528 529 PART NO. 262359 391737 221551 490649 223455 93491 490374 222450 223813 94419 261409 393368 490169 94608[...]

OWNER'S MANUAL HOW TO ORDER REPAIR PARTS 5 HORSEPOWER 3 CUTTING STAGE MULCHING AND BAGGaNG CHBPPER-SHREDDER Each chipper-shredder has its own model number. Each engine has its own model number. The model number for your chipper-shredder will be found on a label attached to the frame_ The model number for the engine will be found on the blower [...]