Casablanca Fan Company 86UxxM инструкция обслуживания

1 FUSE BOX (REMOVE FUSE FOR THE CIRCUIT YOU WILL BE WORKING ON) 18 84 70 CONTENTS INTR ODUCTION 1 MOUNTING RECOMMEND A TIONS 2 F AN INST ALLA TION 3 OPTIONAL EXCLUSIVE LIGHT FIXTURE INST ALLA TION 9 CONTR OL FEA TURES:     TR OUBLESHOO TING 13 PN 8643520 A T1008 BEFORE Y OU ST AR T NO TES [...]

2 7 ′ MINIMUM P ole Length Standard Standard 6” 12” 12” 18” 24” 36” 48” Ceiling Height 8’ 8’ 6” 9’ 9’ 6” 10’ 11’ 12’ 13’ 14’ Suggested Extension Pole Lengths BLADES MUST BE A MINIMUM OF 7 ′ ABOVE THE FLOOR EXTENSION POLE MAXIMUM HANG-TRU® ANGLE 32º 32° MOUNTING RECOMMEND A TIONS SLOPED CEILING INST ALLA TI[...]

3 W i l d e r n e s s ™ IMPORT ANT S AFETY INFORMA TION! BEFORE ST ARTING THE INST ALLA TION OF YOUR CEILING F AN, INST ALL THE THREADED DOWNROD INT O THE MOT OR COUPLING AND LOCK THE ASSEMBL Y ALLEN SET SCREW 1 ⁄ 4 -20 x 1 ⁄ 4 ” (PRE-INST ALLED) 3mm ALLEN WRENCH 6” DOWNROD & BALL ASSEMBL Y MOT OR COVER Prepar e for fan installation a[...]

4 Installing a New Ceiling Fixtur e Outlet Box If you do n ot have an existin g fixture located where you wish to place your Casablanca fan, an approved ceiling fixture outlet box m ust be installed and wir ed. Using Existing Ceiling Fixtur e Outlet Box After turning the power OFF at its source (either circuit break er or fuse box), lower the old[...]

5 W i l d e r n e s s ™ CANOPY LOCK W ASHER (4) CANOPY SCREW (4) Step 3. Pass the lag screw through the center hole of the cr osbar moun ting br ack et an d scr ew in to gui d e hole . Tigh ten until outlet box is firmly mounted to beam. This box must be firmly secured to the ceiling. W e recommen d that the ceiling fixture outlet box be of su[...]

6 WIRE NUT WHITE WIRES (2) GREEN WIRES (3) Step 6. Attach the fan wires to the ceil - in g fix tur e outle t bo x wi rin g by twist in g the bar e ends of the wires togeth er an d then securin g with a wire nut. Connect in this or der:  GREEN leads from moun ting plate and fan to GROUND cond uctor of power source . Secure with wire nut. ?[...]

7 W i l d e r n e s s ™ Step 10. T o r each th e blade hold er m ountin g holes in th e f an motor th e switch housin g cap must be rem oved. T ake out th e two 8-32 X 3 / 8 ” screws securin g the switch housin g cap an d rem ove. Put the two (2) screws asid e for the momen t, th ey will be used in Step 15 to install the switch housing cap afte[...]

8 Step 12. U sing the blade holder screws(pack of 11) attach each blade/blad ehold er assembly to the m otor . Usin g the screwdriver , tighten securely by hand only . Step 14. Line up the two clear ance holes in th e cap with th e two thr eaded holes on the raised rim of the switch housing. Press the cap onto the switch h ousing to seat the gui de[...]

9 W i l d e r n e s s ™ Step 16. Unpack light fixture and make sure everything is accounted f or . Refer to the instru ction sh eet inclu ded with each fixture . Step 17. While holding the li gh t fixture up to the fan connect the wires from th e fixture to the wires fr om th e fan. Black to Blue and White to White by sn apping the conn ector[...]

10 Step 18. Lin e up the two clearance holes in the light fixtures with the two thread ed holes on the raised rim of the switch housin g. Step 19. Using the two 8/32 x 3/8” screws rem oved in step 10, install th e light fixtur e onto th e switch housing. ti gh ten securely by han d only . Step 20. Place a mica shade onto each fixture arm by pu[...]

11 W arning: T o reduce the risk of electrical shock, this fan must be installed with an isolating w all contr ol/switch. SCREW 6-32 X 1” (2) SCREW 6-32 X 3 / 8 ” (2) WOOD SCREW 1” (2) DRYW ALL ANCHOR 6-32 (2) 12V BA TTERY W-73 CONTROL HOLDER Standard Light Switch Step A. Remove the two screws holding the switch cover plate . Do not rem ove t[...]

12 SEND SIGNAL LED Fan Contr ol T o start the f an. Press the selected speed button to run th e fan at th e desired speed . 1=Low speed 2=Medium speed 3=High speed T o turn off th e fan. Pr ess the FAN OFF button. Airflow Dir ection T o r everse the airflow press the REVERSE button. Reverse operates at any speed whether fan is on or off. Th e fan[...]

13 V e r s a •T o u c h 2 ® Befor e Requesting Service: Please follow this tr oubleshooting guide befor e contacting your dealer f or assist ance . PROBLEM POSSIBLE REMEDIES PR OBLEM POSSIBLE REMEDIES .. F AN WILL NOT ST ART •Check m ain circuit fuses , circuit break ers, or wall switch positi on. Check all wire connecti ons, m aking sure th e[...]

14 PRODUCT SPECIFICA TIONS Model Name: W ilderness ™ Model Number: 86UxxM Dimensions: A =16" B = 17" C = 3" D = 11.8" E =5.6" W eight: 50 lbs. Motor: 188 x 20mm Direct Drive™ Blade Span: 54” Blade Iro n Pitch: 14° No . of Blades: 5 T echnolog y :  V ersa•T ouch2®W -73 Airflow: 6,772 cfm Electricit y Use*[...]