Casablanca Fan Company 38DHxxT инструкция обслуживания

1 INTR ODUCTION 1 MOUNTING RECOMMEND A TIONS 2 F AN INST ALLA TION 3 CONTR OL FEA TURES: INTELI•T OUCH OPERA TION 9 INTELI•T OUCH TR OUBLESHOO TING 12 PR ODUCT SPECIFIC A TIONS 13 CIRCUIT BREAKER (TRIP BREAKER FOR THE CIRCUIT YOU WILL BE WORKING ON) FUSE BOX (REMOVE FUSE FOR THE CIRCUIT YOU WILL BE WORKING ON) 18 84 ″ 70 ″ • The blades in[...]

2 Calculation of 32° Use the tear-off Ceiling Angle T emplate card inserted in th e back of this manu al, it provi des you with a simple ‘go’ or ‘no-g o’ for in stalling your f an on a sloped ceiling. SLOPED CEILING INST ALLA TIONS MOUNTING RECOMMEND A TIONS 7 ′ MINIMUM P ole Length 6 ″ 12 ″ 12 ″ 18 ″ 24 ″ 36 ″ 48 ″ Ceiling[...]

3 INST ALLA TION INSTRUCTIONS Unpacking: Befor e assembling and installin g your ceiling f an, remove all parts from th e shipping cartons an d check th em against th e parts listed her e . Befor e discarding pack aging materi al, be certain that all parts have been rem oved. F AN PREP ARA TION GETTING ST ARTED Installing a New Ceiling Fixtur e Out[...]

4 CROSSB AR MOUNTING BRACKET INST ALLA TION JOIST CEILING WIRING CROSSBAR MOUNTING BRACKET FLA T W ASHER GREEN GROUND WIRE CEILING F AN APPROVED WIRING BOX RIDGE SIDE DOWN APPROVED OUTLET BOX HARDW ARE Note: After removing the old fixture , check the outlet box to insure that it is supported by a joist or beam across its upper surface . If not, a [...]

5 CANOPY INST ALLA TION Step 4. A ttach the can opy to the cr ossbar moun ting br acket with three o f the 8-32 x 2 1 / 2 ” long canopy screws and lock washers provid ed with your Casablanca f an. Han d tigh ten until sn ug against the ceilin g. CANOPY SCREW CANOPY LOCK W ASHER FEED OUTLET BOX WIRES THROUGH CANOPY OPENING Note: On sloped ceilings[...]

6 INST ALLING THE UPPER GLASS SHADE UPPER GLASS SHADE BRACKET NOTE: Make a note of the Fan Serial Number and Model Type before install- ing the top cover . Step 5. Car efully place the upper glass shade on the foam covered brack ets. Assure the glass sits evenly on the bracets and is center ed. Step 6. T ake the three upper glass shade brackets and[...]

7 TIL T THE F AN TO INST ALL LAST CANOPY SCREW Step 11. Tu c k t he w i r e s i n t o t h e canopy with the wire nuts pointed upwar ds, so that the WHITE and BLACK wires are on opposite sid es of the canopy and all wires are clear of the canopy openin g. Step 13. Strai ghten the fan, then check to ensure that there is no movem ent between the canop[...]

8 BLADE SCREW (4 PER BLADE) FLA T W ASHER (4 PER BLADE) INST ALLING THE GLASS SHADE INST ALLING THE HALOGEN BULB Step 15. Screw the 100 Watt Halog en bulb into the socket. Do not touch the glass bulb with your fingers–it is extr emely important that the glass be clean. If it is tou ched, or dirty , clean carefully with a tissue . A dirty glass b[...]

9 The wall control installs in the same mann er as an ordinary ligh t switch, using an existin g junction box and wiring. This contr oller is d esign ed to si gnal the f an mi crocomputer as well as perf orm n ormal switchin g oper ations . For this r eason the followin g precauti ons m ust be observed: 1. Use only th e Casablanca W-32 wall con tro[...]

10 Inteli•T ouch ® The PO WE button is n ormally left in the on position. Always turn the power off durin g cleaning or servicing the fan and during thund erstorms. It is also used to exit or en ter additi onal pr ogram s. PO WER must be left on to retain a previously set fan speed or light lev el. Ther e are six individ ual speed settings for t[...]

11 The Light-Min der program automatically turns OFF the fan mounted lights after two hours . T o enter the Light-Minder Program: 1. T urn the PO WER OFF for at least thr ee seconds. 2. T urn the on. 3. Immedi ately operate th e buttons in th e followin g sequence: + + + 4. A series o f tones in dicates this comm and has been accepted . The fan and[...]

12 Before Requesting Service: Please follow this tr oubleshooting guide be- fore contacting your dealer for assistance. Caring for Finishes : For cleaning, a soft brush or lint-free cloth should be used to preven t scratchin g the finish. A vacuum cleaner brush nozzle can rem ove heavier dust. Surface smu dges or an ac- cumulati on of dirt and d u[...]

13 PRODUCT SPECIFICA TIONS Model Name: Bel Air ® Halo Model Number: 38DHxxT Dimensions: A = 13.25" B = 18.5" C = 3" D = 15.5" E = 5.6" Weight: 32 lbs. Motor: XLP-2000 ® Blade Span With: 55" Blade Pitch: 14° No. of Blades: 5 T echnology: Inteli•T ouch ® W-32 Lightbulbs:  100-watthalogen(1)  60-watti[...]