Cable Electronics CELABS HSW88C инструкция обслуживания

INSTRUCTION MANUAL 8x8 HDMI over CAT5 Matrix with IR Pass-through HSW88C CE labs can support many areas of your audio and video distribution needs. W e manufacture: • Digital Signage software and Media Players • HD Matrix Switchers • RF amplifiers • HDMI and Component HD distribution amplifiers • CA T 5 Signal Extenders • VGA Extenders [...]

SAFETEY NOTICE 1. If the DVI or HDMI device requires the EDID information, please use EDID Reader/Writer to retrieve and pr ovide DVI/HDMI EDID infor mation. 2. All HDMI over CA T5 transmission distances are measured using Belden 1583A CA T5e 125MHz LAN cable and ASTRODESIGN Video Signal Generator VG-859C. 3. The transmission length is largely affe[...]

The HSW88C 8x8 HDMI over CAT5 Matrix Switch with IR Pass-through provides the most flexible and cost effective solution in the market to route high definition video sources plus multi-channel (up to 7.1-channel) digital audio from any of the eight HDMI source devices to the remote displays at the same time. Through low cost Cat-5/5e/6 LAN cables, n[...]

• State-of-the-art Silicon Image (Founder of HDMI) chipset embedded for upmost compatibility and reliability • HDMI 1.3c compliant • HDCP compliant • Allows any source to be displayed on multiple displays at the same time • Allows any HDMI display to view any HDMI source at any time • Supports 7.1 channel digital audio • Supports defa[...]

Method C: Software Control Through RS-232 or USB Software Control Menu 1. S can button: Serial Port Scan: Press Scan button, the computer will scan the all com port and display them. Select the RS232 serial port connected to the Matrix switch. And set device ID 255 is for all device. Only the same device id or 255 can get the command you send. Pres[...]

Method A: Push button for switching input channels Press the INPUT SELECT push button to switch the input source on the respective output port connected to the matrix receiver in sequential order . The selected input source will be displayed on the LED of INPUT CHANNEL. Method B1: IR remote control for switching input channels Please press F1 to F6[...]

Method A: Push Button 1. Use the switch button on output port to select which port to be changed. (+) increase (–) decrease 2. Push the switch button on Input channel. The source will be sequentially changed. After few seconds, the setting will be active. Method B: IR Remote Control a. Please press F1 to F8 Enter IR control mode and decide which [...]

HARDWARE INSTALLATION HSW88C as Master 1. Connect all sources to HDMI Inputs on the 8x8 HDMI over CA T5 matrix master HSW88C 2. Connect each DDC output port on the HSW88C to respective DDC port on the remote receiver HSMR 3. Connect each TMDS output port on the HSW88C to respective TMDS input on the remote receiver HSMR 4. Connect IR blaster to the[...]

DIP SWITCH Definition of IR Earphone Jack Supported IR Data Format Data Format Suitable Not Recommended NEC RC5 TOSHIBA MICOM CODE GRUNDIG CODE SONY 12 BIT CODE SONY 15 BIT CODE SONY 20 BIT CODE RCA CODE RCM CODE MA TSUSHIT A CODE MITSUBISHI CODE ZENITH CODE JVC CODE M50560-001P MN6125H MN6125L MN6014_C5D7 MN6014-C6D6 MC14457P LC7464(AHEA) GEMINI_C[...]

IR CONTROL PATH SW Main for firmware update (for technical support only) Note 6. Factory default for SW Main is pin#1-OFF[ ], pin#2-OFF[ ], pin#3- OFF[ ], & pin#4-OFF[ ]. PLEASE MAINT AIN THIS SETTING A T ANYTIME FOR REGULAR USE VIA RS-232 CONTROL! 7. Factory default for SW Main is pin#1-OFF[ ], pin#2-OFF[ ] , pin#3- OFF[ ], & pin#4- ON[ ].[...]