Bulldog Security 1402 инструкция обслуживания

    INSTALLATION GUIDE  OWNER'S GUIDE Keyless Entry and Alarm System Model 1402 BULLDOG SECURITY Creating A Higher Standard Thank you for purchasing an American made product by Bulldog Security . To order additional transmitters or other accessories, visit our website at www.directwholesale.net or call 1-800-659-0764 FOR TECHNIC[...]

    CONTENTS 3 System Features ...............................................4 - 5 System Components .............................................6 Required Tools .....................................................6 Technical Assistance .............................................6 Before You Begin ..................................[...]

    5 SYSTEM FEATURES CONT. On-Board Built-in relay provides a positive (+) Parking parking light output. No relay needed. Light Relay On-Board Door Built-in relay for Type A, Type B and Lock Relay Type C door locks. Plug In Six A visual theft deterrent that flashes when Function LED the system is armed. Lets you know Status Indicator w[...]

    7 BEFORE YOU BEGIN CONT. PRECAUTIONS This system will add remote keyless entry features to any vehicle with power door locks. This will also work as a replacement system for the factory installed keyless entry system. Use masking tape to indicate the preferred mounting locations of interior components, LED and override switch. Disco[...]

    9 6. Use electrical tape to wrap. Be sure to cover the wire about two inches on either side of the connection. First pull the wire that you have just connected along side the wire you connected to, tape and wire tie them together. Use this method for all connections. CAUTION: All wires must be wrapped with tape and wire tied. 5. Wra[...]

    11 LOCATING & MAKING CONNECTIONS CONT. 3. Turn the ignition ON. Probe for a wire that shows 12 volts only when the ignition is on. Confirm this by turning the ignition on and off while probing each wire. 4. Mark this wire with its function Ignition Power. 5. If these wires cannot be located, please call our technical suppo[...]

    13 LOCATING & MAKING CONNECTIONS CONT. CONNECTING THE MAIN WIRING HARNESS TO THE MODULE Carefully plug the main harness into the 1402 module. DO NOT plug the harnesses into the control module until all connections have been made. Be careful to line up the pins on the unit with the wiring harness plug (lip up - Red wire to the ri[...]

    CONNECTING THE CAR HORN WIRE You must use optional part #775. MOUNTING AND CONNECTING THE OPTIONAL SIREN Select a location under the hood for the siren. For best results, the location should meet the following conditions: The mounting location should be solid and have no moving parts nearby. For the loudest sound, the siren sh[...]

    18 TESTING: Door Locks  There are four basic types: Type A Door Lock Test (Most GMs and some Chryslers) Probe both of your door lock wires going to the door lock switch usually located in the drivers kick panel. Attach the clip end of your test light to a good chassis ground. Using the vehicles door lock controls, act[...]

    19 TESTING DOOR LOCKS CONT. wires tests (+) positive when lock is pressed and the other tests (+) positive when they are unlocked, your vehicle has a Type A door locking system. Make sure to mark which wire is lock and unlock. Proceed to Connecting Door Locks, Connecting Door Locks. NOTE: Type A and Type C locks wi[...]

    22 HOW TO USE YOUR REMOTE TRANSMITTER BUTTON #2 OPTION #2 BUTTON #4 BUTTON #1 ARM/DISARM BUTTON #3 OPTION #3 KEYLESS ENTRY FUNCTIONS LOCKING DOORS Press transmitter Button #1 to lock the doors. The parking lights will flash once and the horn or siren will sound acknowledging the unit received the signal. UNLOCKING DOORS Pressing tra[...]

    24 HOW TO USE YOUR REMOTE TRANSMITTER CONT. VALET MODE To activate Valet Mode, first disarm the system. Hold Button #4 for ten (10) seconds and the system will chirp once. Press Button #4 again within two (2) seconds and the system will chirp once again. The LED will remain on when in valet mode. To deactivate the valet mode, repeat[...]

    26 KEEP THIS MANUAL IN YOUR GLOVEBOX TO USE AS A REFERENCE. CLEARING THE E-PROM MEMORY Take the BLACK wire with the green tag and attach it to a chassis ground (shock or microwave sensor input) white plug with the override switch. Then cycle the ignition key from off to run six times within five seconds. The YELLOW WITH [...]

    JBS Technologies, LLC 225 Technology Way Steubenville, OH 43952 Toll Free: 800.878.8007 Fax: 740.282.1201 www.bulldogsecurity.com email: techsupp@bulldogsecurity.com JBS T echnologies produces the world's most innov ative and reliable car alarms, remote starters, keyless entry systems and starter immobilizers. JBS T echnologies[...]