Bryant PSPHA732 инструкция обслуживания

SMAR T TEMP ® ELECTRONIC THERMOST A T INST ALLA TION AND OPERA TING INSTRUCTIONS Mt. Laurel, New Jersey 08054, USA ● www .luxproproducts.com PSPHA732 52091 HEAT OFF COOL SET SUNDAY WEEKDAY PROGRAM SET DAY/TIME PM Choose Heat or Cool Set Day & Time Installs Easily Easy as 1–2–3 • Please read all instructions carefully before beginning i[...]

5:36 72 T U 1. COMP A TIBILITY Y our PSPHA732 is compatible with Heat Pumps Up to 3 Stages of Heat and 2 Stages of Cooling. This includes Auxiliary and Emergency Heat. It cannot be used with 120 volt heating systems or 3 wire zone valves. Ask your dealer for other LUXPRO thermostats to control those systems. 2. FEA TURES • Heating and Cooling •[...]

C A U T I O N: Y our thermostat is protected against normal static electric discharges. T o minimize the risk of damaging the unit in extremely dry weather , touch a grounded metal object before touching your thermostat. 4. INST ALLATION 4.1 TOOLS REQUIRED • #1 Phillips screwdriver (small) • Drill with 3/16-in. (4.8mm) bit • Wire stripper/cut[...]

C A U T I O N: • Be careful not to drop the unit or disturb electronic parts. • Leave the door closed while the body is being removed from the base. 9. Route the wires through the open areas in the base plate above the terminals. Hold the base against the wall, with the wires coming through. Position the base for the best appearance (to hide an[...]

NOTE: If you have an electric system and the blower does not operate after installation, verify that the electric/gas option in installer set up is set to Electric, see SETUP OPTIONS. 18. Y our installation is now complete. 5. OPERA TING BASICS 5.1 UP/DOWN CHANGE KEYS • These are the two upper keys, just right of the units display . They are used[...]

• If a second stage of heat is called for , the flashing rate of HEA T increases • If the 3rd stage of heat activates, the display will also flash "AUX " in addition to HEA T flashing. 5.7 COOL • Use COOL mode to control your air conditioner , cooling your home. • In COOL mode, COOL is displayed right of the set temperature. • C[...]

5.12.3 CLEAN CYCLE ® • LUX’ s Clean Cycle ® allows you to program a forced air system to flow air through your system’ s filter , cleaning the air in your home, even when heating or cooling is not being utilized. In CLEAN mode the fan maintains the programmed minimum run time; it may run additional time as required to maintain temperature c[...]

to accept the displayed start time and advance to the HEA T SET TEMPERATURE, it will flash to show that it may be edited. • The HEA T SET TEMPERATURE will be displayed on the right side of the display with the HEA T indicator visible. • Edit the HEA T SET TEMPERATURE, then press NEXT to accept and advance to the COOL SET TEMPERA TURE, it will f[...]

0 to 60 minutes in increments of 3 minutes. Set 0 MIN/HR to allow AUTO control for particular periods while CLEAN is used in others. Set the fan duration to 60 MIN/HR to run the fan continuously for this period. • Press NEXT to advance to the next period. After the four program periods of day have been programmed, pressing NEXT will advance to th[...]

• Use UP/DOWN keys to adjust the filter limit in 10-hour increments to the recommended value. • Rotate the dial to RUN to finish this setting. 7.3 ENERGY USAGE Y our thermostat records the total number of hours the thermostat has activated heating and cooling with six separate timers. They measure: • T oday’ s cumulative heating time. • Y[...]

11 3 to 6 times per hour . A smaller swing number increases the number of cycles, so room temperature is more constant. A larger swing number decreases the number of cycles, saving energy in most cases. 7.6.1 SWING 1 – 1st ST AGE This setting controls when the first stage of heating or cooling turns on and off. • In HEA T , Swing 1 sets the tem[...]

12 board. For reference, there are a table of settings and jumper positions printed there as well. They are described here from J3, the rightmost jumper , to J7, the leftmost jumper . 8.1 MINIMUM RUN TIME – J3 • The position of J3 sets the minimum length of time that the thermostat must remain with HEA T or COOL either on or off before it will [...]

13 9.1 BA TTERY INST ALLA TION 1. Remove fresh batteries from their carton. 2. Remove body of thermostat from the wall as described in installation. 3. Remove the used batteries if present and replace them within 90 seconds to avoid having to reset the day and time. 4. Install two new "AA" size Energizer ® or Duracell ® Alkaline batteri[...]

14 12. WIRING DIAGRAMS WIRING DIAGRAM NOTES 1. Dashed wires are optional. 2. If an "E" wire was connected to your old thermostat, it should be re-connected to the "E" terminal on the new thermostat, and the optional jumper between "W" and "E" should not be used. Install this optional jumper if you would like [...]

15 HEA T PUMP SYSTEM NEW THERMOST A T AND T APE OFF WITH COMMON TERMINAL CORRESPONDING TERMINALS NOT USED EG YY 2 R OW 1 W 2 B C L AMANA G Y1 RC-RH W1 W2 X1 AMANA PHD-2,-3,-4,or -5 G R W W1 C ARCO / Friedrich X2 G Y RC W2 C L ARCO / Snyder General E G Y R O W1 C X BARD E G Y1 R W2 B X L BARD, HP , WH, MHP , HPQ E G Y R W2 W1 X L BDP / BRY ANT E G Y[...]

16 DA Y MON MORN DA Y EVE NIGHT MORN DA Y EVE NIGHT MORN DA Y EVE NIGHT TUES WED PERIOD HEA T TIME TEMP . TIME TEMP . COOL DA Y THURS MORN DA Y EVE NIGHT MORN DA Y EVE NIGHT MORN DA Y EVE NIGHT MORN DA Y EVE NIGHT FRI SA T SUN PERIOD HEA T TIME TEMP . TIME TEMP . COOL 14. USER PROGRAM T ABLE Before hitting the software reset button, record your the[...]