Bogen CSUB инструкция обслуживания

© 2008 Bogen Communications, Inc. All rights reserved. Specifications subject to change without notice. 54-2 1 7 1 -0 1 B0 8 1 0 Ceiling Subwoofer Model CSUB Inst allation and Use Manual[...]

2 Pr oduct Description Thank you f or choosing Bogen’ s CSUB Ceiling Subwoof er . Please familiarize yourself with the product b y r eading and re vie wing the descriptions and diagrams in this manual. Bogen’ s CSUB delivers unsurpassed perf ormance and value. This subw oofer can be installed either in suspended ceiling structures or har d surf[...]

Pr oduct Diagrams Fr ont Drawing (grille removed) 1 . Driver Assembly (internal) 2. Bass T uning V ent 3. Grille Retention Groo ve 4. 24 " Ceiling Tile Guide Arro ws (×2) 5. P ow er T ap Selection Switch 6. 1 4- 1 /2 " Joist Space Guide Arr ows (×2) 7. Mounting Clamp Scre ws (×4) Side Drawing 8. Metal Back Can 9. Snap-Lock Input Connec[...]

4 Speak er Placement The low fr equency capability of the CSUB allows gr eat flexibility in its placement. While full-range speak ers will typically be installed thr oughout the ceiling in an evenl y spread pattern, the CSUB can be placed where ver it is most con venient. This usually means where the subw oofers best meet the needs of the overall s[...]

5 IMPOR T ANT There m ust be a minimum of 11 " of v er tical clearance ( 1 2- 1 /4" if using the CK 1 0 Safety Cable Kit) betw een the fr ont of the mounting surface and any other structure in the ceiling f or the speak er to fit. Before cutting the full hole, inves- tigate for depth and clearance by cutting a small hole, or removing the [...]

6 Installation (cont.) SUSPENDED CEILINGS: 1 . Remov e the ceiling tile fr om the ceiling grid. Cut a 1 4- 1 /4" circular hole in the ceil- ing tile. Use the included template as a guide. 2. Put the CSUB face down on a w orkbench or on the floor without grille installed . 3. Place the ceiling tile ov er the CSUB, making sure the ceiling tile i[...]

7 Installation (cont.) DR YW ALL OR O THER HARD SURF A CES: 1 Be sure y ou know the location of the ceiling joists before cutting the speak er open- ing. Cut a 1 4- 1 /4" cir cular hole where the CSUB will be installed. Use the includ- ed template as a guide. 2. Mak e electrical connections to the snap-lock input connector and then plug it int[...]

8 Speak er Wiring All wiring should be done prior to installation and then plugged into the rear of the speak er . Wiring is terminated at a snap-lock input connector . There are tw o positive and two negativ e terminals to accommodate daisy-chaining of speak ers in a sys- tem. Daisy-Chaining The snap-lock input connector allows f or easy daisy-cha[...]

9 Selecting P o wer Le v els The front-mounted selector s witch is used to set the appr opriate power lev el or impedance for your system. Using your f ingers or a flat-blade scre wdriver , turn the knob until the arr ow points to the power le vel you requir e . 70V Systems A pow er setting scale for 70V systems is labeled on the switch. Six settin[...]

10 Specifications * Half-space response (ceiling-mounted), 8-ohm input † Front panel, switch-selected Accessories CK 1 0 ( 1 0-Ft. Safety Cable Kit) The CK 1 0 is a 1 0-foot cable with one looped end and an adjustable cable clamp . It is suitable for use as a safety cable. On the CSUB Ceiling Subwoofer , the CK 1 0 attaches to the safety tether p[...]

11 The Bogen Ceiling Subwoofer , model CSUB, is warranted to be free from defects in material or workmanship for three (3) years from the date of sale to the original purchas- er . Any part of the product covered by this warranty that, with normal installation and use, becomes defective will be repaired or replaced by Bogen, at our option, provided[...]

50 S pring S treet, Ramsey , NJ 07446, U.S.A. T el. 201-934-8500, Fax: 201-934-9832, www .bogen.com[...]