BLACKHAWK! PORTO-POWER B65114 инструкция обслуживания

Model Number B65 114 B65 115 Capacity 4 Ton 10 Ton Porto-Power Kit Operating Instructions & Parts Manual - Before using this product, read this manual and follow all its Safety Rules and Operating Instructions SFA Companies 10939 N. Pomona Ave. Kansas Cit y , MO 64153 816-891-6390 sales@blackhawk-automotive.com Made in China B65 114-M0 rev 11/0[...]

2 ONE YEAR LIMITED WA RRANTY For a period of one (1) year from date of purchase, S FA Companies will repair or replace, at its option, without charge, any of its products which fails due to a defect in material or workmanship under normal usage. This limited warranty is a consumer's exclusive remed y. Performance of any obligation under this w[...]

3 SA VE THESE INSTRUCTIONS For your safet y , read and understand the information contained within. The owner and operator shall have an under- standing of this product and safe operating procedures before attempting to use this product. Instructions and Safety information shall be conveyed in the operator's native language before use of this [...]

GENERAL SAFETY INFORM ATION 1. Ensure that attachments are fully engaged before applying load. 2. Ensure that load is centrally applied to attachment or ram saddle. Do not load off cente r. 3. Always monitor the force applied to workpiece by using a load cell and indicator or you may monitor pressure developed in the ram by using an inline pressure[...]

! Hydraulic Hoses and Fluid Transmission Lines • Avoid short runs of straight line tubing. S traight line runs do not provide for expansion and contraction due to pressure and/or temperature changes. • Reduce stress in tube lines. Long tubing runs should be supported by brackets or clips. Before operating the pump, all hose connections must be [...]

OPER ATION Note: Inspect before each use for evidence of fluid leaks, damaged hydraulic fittings, bent or broken attachments and missing parts. 1. Locate and close release valve by turning it clockwise until firmly closed. (Do not over tighten) 2. Operate by pumping handle. This will send fluid from the pump reservoir into the high pressure hose as[...]

B. Clamp & Pull C. Spread (i) Vertical Spread (ii) Horizontal Spread (iii) Hydraulic Spreader Ram Toe Ram Extension Tube Flat Base Ram Toe Ram Plunger T oe Hydraulic Spreader Chain (i) Clamp with Pull Ram (ii) Pull with Chain Chain Pull Plate Saddle Ram Lifting T oe Pull Ram Plunger Base 7 Basic Setup The capacity of the Porto-Power Kit can be [...]

8 How to bleed air from system 1. Bleed air from ram : Place pump at a higher elevation than the hose and ram (refer to figure 4). The objective is to "float the air bubbles up hill and back to the reservoir where they belong. Close valve and extend ram as fast as possible. Open valve fully allowing oil and air to return to reservoi r. Repeat [...]

9 Figure 5 - Replacement Parts Illustration for B65 114 Replacement Parts for Model B65 114 It em # Pa rt # De scription Qty. 1 B65161 Extension Tube (19-1 /2") 1 2 B65160 Extension Tube (16-1 /2") 1 3 B65159 Extension Tube (8-1 /2") 1 4 B65158 Extension Tube (6-1 /8") 1 5 B65157 Extension Tube (3 ") 1 6 B65177 Male connect[...]

Figure 6 - Replacement Parts Illustration for Model B65 115 Replacement Parts for Model B65 115 10 It em# Pa rt# De scription Qty. 1 B65162 Ext en si on Tube (27 ") 1 2 B65163 Ext en si on Tube (18 ") 1 3 B65164 Ext en si on Tube (10 ") 1 4 B65165 Ext en si on Tube (4 ") 1 5 B65179 Male Conne ct or 1 6 B65166 Wedge Head (offset)[...]

Load - Pressure Correlation For Model B65 114 & B65 115 Always monitor the force applied to workpiece by using a load cell and indicator or you may monitor pressure developed in the ram by using an inline pressure gauge, then calculate the applied force using the formula: F = P x A For model B65 114, A = 0.998 in² ; For model B65 115, A = 2.4 [...]

memo.[...]