Bissell 3574 инструкция обслуживания

USER’S GUIDE 3574/3576 SERIES Safety Instructions 3 Product View 4 Assembly Instructions 5-6 Operation / Special T ools 6-8 Maintenance 8-12 T roubleshooting 12-13 Warranty 16 Replacement Parts 14 Consumer Services 15 CleanView ® II BAGLESS DJ68-00280A REV(0.1) ug603-2559_3574-3576_1005.indd 1 ug603-2559_3574-3576_1005.indd 1 1/4/06 9:45:49 AM 1[...]

2 Thanks For Buying A BISSELL CleanV iew ® II We’ re glad you purchased a BISSELL CleanView II Vacuum. Everything we know about floor care went into the design and construction of this complete , high-tech home vacuuming system. Y our BISSELL CleanView II is well made, and we back it with a limited comprehensive one-year warr anty . W e also sta[...]

3 IMPOR T ANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should be observed, inc luding the following: READ ALL INSTRUCTIONS BEFORE USING Y OUR UPRIGHT V ACUUM. Always connect to a polarized outlet (left slot is wider than right). Unplug from outlet when not in use and before conducting maintenance. W ARNING: T o redu[...]

4 C AUTION: Do not plug in your vacuum cleaner until you are familiar with all instructions and operating pr ocedures. Power Switch Carrying Handle Crevice T ool Post-Motor Filter Quick Reach ® Handle Handle Quick Release Cord Wrap Handle Release Pedal Powerfoot Stretch Hose Extension W and Power Cord Furniture Protection Guard Height Adjustment K[...]

The only tool you’ll need to assemble your vacuum cleaner is a screwdriver . Locate the vacuum Handle and remove the screw packet taped to the base of the Handle. Stand the vacuum upright and slide the base of the Handle firmly into the grooves at the top of the vacuum body . Check to be sure the Handle is fitted to the vacuum body . If there is [...]

Press the Handle Release Pedal with your foot to place your vacuum in one of three cleaning positions. Upright- For storage and above floor c leaning with tools. Normal Cleaning- Press Handle Release Pedal once. Use for most household floor cleaning tasks. Low Cleaning- With the vacuum in normal c leaning posi- tion, press Handle Release Pedal agai[...]

Y our BISSELL CleanView II is not only a pow- erful carpet and rug vacuum cleaner , it’ s also a versatile above floor vacuum cleaner when you select one of the special tools. Raise Handle to Upright Position. Grasp the Quick Reach Handle and lift Hose Wand to separate from suction intake opening. Attach tools by firmly pushing onto Vacuum Hose o[...]

T o maintain maximum cleaning performance, the following maintenance steps must be performed: Empty the Dirt Container when the dirt reaches the “Full” line on the side. Check the Inner and Outer Circular Filters and the Pre-Motor Filter at least once a month and clean or replace as needed. Replace the Post-Motor F ilter every three to six mont[...]

Separate the Outer foam and Inner pleated Circular Filters. Wash each individually by hand in warm water . Mild detergent may be used if desired. Rinse well, then air dry thoroughly before putting them back together and replacing in Filter Cup. The Filter Cup may be washed in warm water with a mild detergent. Make sure it is completely dry before r[...]

For standard models , remove the four screws as shown with a Phillips Head Screwdriver . Lift the Brush Cover off. For wide cleaning path models , Lift tab 1 and release the three latches in order 2-4 as marked. Lift the Brush Cover off. Grasp Rotating Floor Brush at both ends and lift. Clean strings, hair and other debris from Rotating Floor Brush[...]

Determine the light bulb type of your vacuum: Standard Bulb (#203-1297) – approximately 1” long, flat end Large Bulb (#203-1007) – approximately 2” long, round end Standard Bulb – remove the bulb from the socket by grasping bulb and pulling straight out. Install the new bulb by pushing it gently into the socket until the bulb snaps into p[...]

12 T roubleshooting Vacuum c leaner won’t run P ossible Causes Remedies P ower cord not plugged in Check electrical plug Blown fuse/tripped breaker Check/Replace fuse or reset breaker Vacuum c leaner won’t pick up dirt P ossible Causes Remedies Incorrect Height Adjustment Adjust Powerfoot to correct height setting Hose not attached to suction o[...]

Vacuum c leaner won’t pick up dirt continued P ossible Causes Remedies Dirt Container not installed properly Position correctly and lock in place F ilters are dirty Check and clean Inner and Outer Circular Filters, Pre-Motor and Post-Motor Filters Louvers missing or installed incorrectly Check for a clog in the tube in the center of the Dirt Cont[...]

14 Replacement P arts – BISSELL Cleanview II Series 1 2/3 4 5 6 8/9 10 11 12 14 15 16 17 13 7 Y ou may purchase replacement parts from your retailer , by calling BISSELL Consumer Services or by visiting our website. T o loca te a retailer near you, or to place an order using Visa, MasterCard, Discover or American Express, call BISSELL Consumer Se[...]

BISSELL Consumer Services For information about repairs or replacement parts, or questions about your warranty , call: BISSELL Consumer Services 1-800-237-7691 Monday - Friday 8 a.m. — 10 p.m. ET Saturday 9 a.m. — 8 p.m. ET Or write: BISSELL Homecare Inc . PO Box 3606 Grand Rapids , MI 49501 A TTN: Consumer Services Or visit the BISSELL website[...]

Warranty 16 This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state. If you need additional instruction regarding this warranty or have questions regarding what it may cover , please contact BISSELL Consumer Services by E-mail, telephone, or regular mail as described below. Limited One Y [...]