Bertazzoni PM60 4 0 X инструкция обслуживания

INSTRUCTIONS FOR THE INSTALLATION, MAINTENANCE AND USE OF FIXED HOBS WI TH GAS OR MIXED SUPPLY DIMENSIONS: (605 mm) (W) x (520 mm) (D) M o d e l s PM6030X (TYPE PM6V) ‘A’ M o d e l s PM6040X (TYPE PM6V) ‘B’ 310733[...]

2 Read this instruction bookl et before installing and using the applia nce. The manufacturer will not be res ponsible for any damage to property or to persons caused by incorrect installation or improper use of the appliance. The manufacturer reserves the rig ht to make changes to its products when co nsider ed ne cessary and useful, without affec[...]

3 DO NOT MODIFY THIS APPLIANCE. Descriptions DESCRIPTIVE CAPTION FOR HOB DESCRIPTION OF HOBS 1. Dual burner Model ‘A’ Fig. 11 2. Rapid burner Model ‘B’ Fig. 12 3. Medium burner 4. Small Burner 5. Dual in burner control knob 6. Dual out burner control knob 7. Rapid burner control kno b 8. Medium burner control knob 9. Small burner control kn[...]

4 L7 925 B3 (*) 60 L8 40 B4 (*) 152 L9 172 (*) Note: -B1 is the min. clearance between the front edge of the applia nce and the front edge of the cabinet. -B2 and B4 are the min. cl earance between the l eft/right side edge of the applianc e and the side wall (if present). -B3 is the min. clearance between the b ack edge of the appliance and the ba[...]

5 CONNECTING THE APPLIAN C E TO THE GAS SUPPLY Before connecting the appliance to the ga s supply you first need to remov e the plastic protective plug for the gas supply which is inserted und er pressure in the gas inlet connection. To remove the plug simply unscrew it. Then make sure that the details sho wn on the label on the lower part of the c[...]

6 CAUTION: save the orifices remov ed from the appliance for future use Regulation of burners Regulation of the "MINIMUM" on the burners To regulate the minimum on the burners carry out the following proce dure indicated below: 1) Turn on the burner and put the knob onto position MINIMUM ( small flame ). 2) Remove the knob ( Fig. 10) of t[...]

7 BEFORE LEAVING When the installation is co mplete, always check for gas leak s using a soapy solution. Never use a flame to make this check. Ignite all burners on high flame to ensure correct opera tion of gas valves, burne rs and ignition. Turn gas taps to low flame position and observe each burne r to ensure t hey ignite completely at all ports[...]

8 Tips for using burners correctly : WARNING: During use of ea ch gas burner(s) adjust the bu rner flame size properly so it does not extend beyond the edge of the cook ing utensil. This is an instruct ion based on safety considerations - Use suitable pots for each burner (see Fig. 14 and Table B) - When the liquid is boiling, turn down the knob to[...]

9 Cleaning the burner caps: Lift the burn er caps from the burner heads and wash them in soapy water and dry thoroughly. Before replacement on the burne r head en sure that the holes are not clogged. SERVICE & MAINTENANCE INSTRUCTIONS Service and maintenance only to be carried out by an authori sed person Routine maintenance Have the condition [...]

10 After-sales technical service and spare parts Before leaving the factory, this appliance wa s tested and adjusted by spe cialist skilled staff to give the best operating results. Any subsequent necessary rep airs or adjustments must be carried out with the greatest care and attention by auth orised personnel. For th is reason, we strongly advise[...]

11 Fig 1 Fig 2 Fig.3 Fig. 3A Fig. 3B[...]

12 Fig.4 Fig.5A Fig.5B Fig.6 Fig.7 Fig.8 Fig.9 Fig.10[...]

13 Fig.11 Fig.12 Fig.13 Fig.14 Fig.15[...]

14 Fig.16[...]