Audio Analogue SRL AUDIO ANALOGUE INTEGRATED AMPLIFIER инструкция обслуживания

AUDIO ANALOGUE INTEGRATED AMPLIFIER OWNER’S MANUAL MANUALE D’ISTRUZIONI[...]

2 INTRODUCTION AUDIO ANALOGUE does not take any responsibilities in the following cases: Whenever the operational procedures related to the use and the maintenance of the equipment, as described in this manual, are n ot respected. Whenever damages to the equipment occur because of fixing or modi fications m ade from non-authorized staff or because [...]

3 PREMESSA AUDIO ANALOGUE non accetta responsabilità nei casi in cui: Le procedure operative di utilizzo e manutenzione de ll’apparato descritte nel manu ale non siano rispettate. I danni si verifichino in seguito a riparazioni o modifiche dell’apparato eseguite da personale non autorizzato o a seguito di normale deterioramento dell’apparato[...]

4 Dear Audiophile , congratulations and thank you for choosing the Audio Analogue Class A integrated amplifier. You’re now the owner of a unit that establishes a new reference in the category of high-quality and high-versatility stereophonic products. The Class A , a dual-mono design, provides circuital solutions with no compromises and features [...]

5 Front panel • SELECT ( 1 ) . Inputs selector. It allows selecting the desired source. The selected input is shown in the central display. • VOLUME ( 2 ) . Volume control. Rotate it clockwise to increase t he volume; counterclockwise to decrease it. The volum e level is shown in the central display. The maximum level is 48. • STAND-BY BUTT O[...]

6 Back panel • RIGHT SPEAKER OUT : Right speaker out connector. • LEFT SPEAKER OUT : Left speaker out connector. • TAPE OUT : Tape output. • INPUT 1,2,3,4,5 : Unbalanced line inputs. • BALANCED INPUT 6 : Balanced line input. • AC MAINS : Connect here the provided power cord. • FUSE : If necessary, replace it with an other of the same [...]

7[...]

8 Remote control • STBY. Standby. Activates/deactivates standby mode. • VOL+/VOL-. Volume setting. • MUTE. Activates/deactivates muting. When muting is activated, volume level is reduced to zero level. When deactivated the volume level is increased, in some seconds, to t he level set before the muting • IN+/IN-. Allows source selection and [...]

9 Unpacking and checking Class A package Carefully open the package to avoid damaging the content. The package should contain: • 1 Class A integrated amplifier. • 1 remote control. • 1 power cord. • 2 AAA batteries (already placed in the remote control). • 1 instruction manual. If one of the items listed above is missing, please contact y[...]

10 Powering up Class A When you set the rear switch of Class A in the position “1”, the unit turns on in th e STANDBY mode. When the front button is ke pt pressed for at least three seconds or when the “STBY” button on the remote control is pressed, the amplifier turns on. The ampl ifier will powers up about in ten seconds. During power up [...]

11 Set-up Class A is provided with a set-up function for activating/deactivating the line 5 by-pass and to change the balance between rig ht and left channel. Set-up is easy to configure. When you press the “SET ” button on the remote control, you enter in a menu that you can roll pressing the “IN+/IN-“ button on the remote control. To make[...]

12 Specifiche Tecniche Parametro Condizioni di misura Valore Numero di canali: - 2 Potenza: 8 Ω @ 1%THD 4 Ω @ 1%THD 2 Ω @ 1%THD 50W 100W 200W Distorsione armonica totale: 1W, 8 Ω 0,02% Sensibilità: Per 50W @ 8 Ω - Volume = 48 Ingresso sbilanciato Ingresso bilanciato 0.5 V rms 1 V rms Tempo di salita: A piena potenza 2.2 µs Slew rate Lim[...]

13 Ricerca Guasti Sintomo Causa Rimedio Cavo di alimentazione non inserito correttamente Controllare che il cavo di alimentazione di rete sia ben inserito nell’amplificatore e nella presa di rete Fusibile bruciato Controllare i fusibili nel portafusibili (dopo aver staccato il cavo di alimentazione dalla presa di rete) sopra la presa IEC ed event[...]