Asus PR-DLS533 инструкция обслуживания

Motherboard PR-DLS533 User Guide[...]

ii Checklist Copyright © 2003 ASUST eK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes[...]

iii Features Contents Notices ........................................................................................... vi Safety information ......................................................................... vii About this guide ............................................................................ viii How this guide is organized .[...]

iv Safeguards Contents 2.6 Expansion slots ................................................................. 2-1 1 2.6.1 Installing an expansion card ................................. 2-1 1 2.6.2 Configuring an expansion card ............................. 2-1 1 2.6.3 PCI slots .............................................................. 2-13 2.7 [...]

v Contents Chapter 5: OS Installation 5.1 Support CD contents .......................................................... 5-1 5.1.1 Drivers ................................................................... 5-1 5.1.2 Management Sofware ............................................ 5-1 5.1.3 Utilities .................................................[...]

vi Notices Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tes[...]

vii Safety information Electrical safety • T o prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect al[...]

viii About this guide This user guide contains the information you need when installing the ASUS PR-DLS533 motherboard. How this guide is organized This manual contains the following parts: • Chapter 1: Product introduction This chapter describes the features of the PR-DLS533 motherboard. It includes brief descriptions of the special attributes o[...]

ix Conventions used in this guide T o make sure that you perform certain tasks properly , take note of the following symbols used throughout this manual. Where to find more information Refer to the following sources for additional information and for product and software updates. 1. ASUS W ebsites The ASUS websites worldwide provide updated informa[...]

x ASUS contact infor mation ASUST eK COMPUTER INC. (Asia-Pacific) Address: 150 Li-T e Road, Peitou, T aipei, T aiwan 1 12 General T el: +886-2-2894-3447 General Fax: +886-2-2894-3449 General Email: info@asus.com.tw T echnical Support MB/Others (T el): +886-2-2890-7121 (English) Notebook (T el): +886-2-2890-7122 (English) Desktop/Server (T el): +886[...]

xi PR-DL S533 specif ications summar y CPU Chipsets Front Side Bus (FSB) Memory Onboard LAN Onboard SCSI Onboard VGA Expansion slots Rear panel I/O Internal connectors BIOS features Support for Intel ® Xeon ™ processor On-die 512KB L2 cache RCC Grand Champion LE Server (GCLE) RCC Champion South Bridge 5.0 (CSB5) RCC Champion I/O Bridge 2.0 (CIOB[...]

xii PR-DL S533 specifications summar y Extended A TX form factor: 12 in x 13 in (30.5 cm x 33 cm) Device drivers Management software Utilities Contact information Form Factor Support CD contents * Specifications are subject to change without notice.[...]

Chapter 1 This chapter describes the features of the PR-DLS533 motherboard. It includes brief explanations of the special attributes of the motherboard and the new technology it supports. Product introduction[...]

ASUS PR-DLS533 motherboard Chapter summar y 1.1 W elcome! ........................................................ 1-1 1.2 Package contents .......................................... 1-1 1.3 Special features ............................................. 1-2 1.4 Motherboard overview ................................... 1-6[...]

ASUS PR-DLS533 motherboard user guide 1-1 1 . 1 Welcome! Thank you for buying the ASUS ® PR-DLS533 motherboard! The ASUS PR-DLS533 motherboard delivers a host of new features and latest technologies making it another standout in the long line of ASUS quality server motherboards! The PR-DLS533 incorporates dual Intel ® Xeon ™ processors in 603/ [...]

1-2 Chapter 1: Product introduction 1 .3 Special features 1.3.1 Product highlights Latest processor technology The PR-DLS533 motherboard supports the Intel ® Xeon p rocessor via d u al 603/604- pin surface mount ZIF sockets . The processor features the Intel ® NetBurst ™ micro-architecture that includes hyper-pipelined technology , a rapid exec[...]

ASUS PR-DLS533 motherboard user guide 1-3 Onboard LAN The motherboard comes with the Intel ® 82540EM 32-bit PCI Gigabit Ethernet controller and the Intel ® 82544GC 64-bit PCI-X Gigabit Ethernet controller to support the latest LAN technologies. The Intel ® 82551QM Fast Ethernet controller is an option. Onboard VGA The A TI Rage-XL PCI-based VGA [...]

1-4 Chapter 1: Product introduction 1.3.2 V alue-added solutions T emperature, fan, and voltage monitoring The CPU temperature is monitored by the ASUS ASIC to prevent overheating and damage. The system fan rotations per minute (RPM) is monitored for timely failure detection. The system voltage levels are monitored to ensure stable supply of curren[...]

ASUS PR-DLS533 motherboard user guide 1-5 Auto fan off The system fans power of f automatically when the system is in sleep mode. This feature reduces both power consumption and system noise. Chassis intrusion detection The motherboard supports chassis intrusion monitoring through the ASUS ASIC. A chassis intrusion event is retained in the system m[...]

1-6 Chapter 1: Product introduction 1 .4 Motherboard over view Before you install the PR-DLS533 motherboard, familiarize yourself with its physical configuration and available features to facilitate the motherboard installation and future upgrades. A sufficient knowledge of the motherboard specifications will also help you avoid mistakes that may d[...]

ASUS PR-DLS533 motherboard user guide 1-7 9 16 1 2 4 3 6 7 10 11 12 13 8 14 15 17 18 5 20 19 21 22 27 26 23 25 24[...]

1-8 Chapter 1: Product introduction DDR DIMM sockets. These six 184-pin DIMM sockets support up to 12GB system memory using registered ECC PC2100/1600 DDR DIMMs. 8-pin 12V SSI power connector . This power connector is for an A TX power supply . 24/20-pin A TX power connector . This power connector is for an A TX power supply . ServerW orks ® Grand[...]

ASUS PR-DLS533 motherboard user guide 1-9 Ultra320 SCSI connectors. These dual-channel 68-pin Ultra320 SCSI connectors support up to 30 SCSI devices, and data transfers of 320Mbps. LSI ® Ultra320 SCSI controller . The LSI 53C1030 SCSI controller supports up to 30 SCSI devices through the onboard dual-channel SCSI connectors. Flash ROM. This 4Mb fl[...]

1-10 Chapter 1: Product introduction LPC super I/O controller . This Low Pin Count (LPC) interface provides the commonly used Super I/O functionality . The chipset supports UART compatible serial ports, one parallel port with EPP and ECP capabilities, a floppy drive, and PS/2 keyboard and mouse. ServerW orks ® 64-bit I/O Bridge (CIOB-X2). (See des[...]

Chapter 2 Hardware information This chapter describes the hardware setup procedures that you have to perform when installing system components. It includes details on the switches, jumpers, and connectors on the motherboard.[...]

ASUS PR-DLS533 motherboard Chapter summar y 2.1 Motherboard installation ............................... 2-1 2.2 Motherboard layout ....................................... 2-2 2.3 Before you proceed ....................................... 2-3 2.4 Central Processing Unit (CPU) ..................... 2-3 2.5 System memory .............................[...]

ASUS PR-DLS533 motherboard user guide 2-1 2. 1 Motherboard ins tallation Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. The PR-DLS533 uses the extended A TX form factor that measures 12 inches x 13 inches (30.5 x 33 cm). Do not overtighten the screws! Doing so may damage the [...]

2-2 Chapter 2: Hardware information 2.2 Motherboard layout Primary IDE FLOPPY ASUS ASIC with Hardware Monitor CHASSIS 4Mbit Flash BIOS WOL_CON PCI-X2 (64-bit, 133MHz 3V) A TX_POWER Intel 32bit PCI LAN Controller AT I RAGE XL VGA Controller USB2 WOR SCSI-B PCI6 (32-bit, 33MHz 5V) SCSI_EN BUZZER ERMC ServerWorks CMIC-LE North Bridge ® ServerWorks RC[...]

ASUS PR-DLS533 motherboard user guide 2-3 2.3 Before you proceed T ake note of the following precautions before you install motherboard components or change any motherboard settings. 1. Unplug the power cord from the wall socket before touching any component. 2. Use a grounded wrist strap or touch a safely grounded object or to a metal object, such[...]

2-4 Chapter 2: Hardware information Note in the illustration that the CPU has a gold triangular mark on one corner . This mark indicates the processor Pin 1 that should match a specific corner of the CPU socket. Incorrect installation of the CPU into the socket may bend the pins and severely damage the CPU! 1. The motherboard supports either one or[...]

ASUS PR-DLS533 motherboard user guide 2-5 Follow these steps to install a CPU. 1. Locate the 603/604-pin ZIF sockets on the motherboard. Unlock the socket by pressing the lever sideways, then lift it up to at least 1 15 ° angle. 2. Position the CPU above the socket as shown. 3. Carefully insert the CPU into the socket until it fits in place. Make [...]

2-6 Chapter 2: Hardware information The Intel ® Xeon ™ processors require specially designed heatsink and fan assembly to ensure optimum thermal condition and performance. Follow these steps to install the CPU heatsink and fan. 2.4.3 Installing the CPU heatsink and fan 1. Place the heatsink and fan assembly on top of the installed CPU, making su[...]

ASUS PR-DLS533 motherboard user guide 2-7 3. Use a small flat screw driver to attach the other end of the bracket, while firmly holding down the heatsink and fan assembly . The middle hook of the bracket snaps in place if you properly attached the two ends. 4. As shown, the middle hook of the bracket snaps in place if you properly attached the two [...]

2-8 Chapter 2: Hardware information 2.5 System memor y 2.5.1 Overview The motherboard comes with six Double Data Rate (DDR) Dual Inline Memory Module (DIMM) sockets. These sockets support up to 12GB system memory using 184-pin registered PC2100/1600 DIMMs with Serial Presence Detect (SPD) and Error Check and Correction (ECC). A DDR DIMM is keyed wi[...]

ASUS PR-DLS533 motherboard user guide 2-9 2.5.2 Memory Configurations The motherboard supports system memory of up to 12GB in a two-way interleaved configuration. As a rule, this configuration requires that you install identical DDR DIMMs (exactly the same type and size) in pairs. For example, if you installed a 512MB module into DDRA1, you must in[...]

2-10 Chapter 2: Hardware information 2.5.3 Installing a DIMM Make sure to unplug the power supply before adding or removing DIMMs or other system components. Failure to do so may cause severe damage to both the motherboard and the components. Follow these steps to install a DIMM. 1. Unlock a DIMM socket by pressing the retaining clips outward. 2. A[...]

ASUS PR-DLS533 motherboard user guide 2-11 2.6 Expansion slots In the future, you may need to install expansion cards. The following sub- sections describe the slots and the expansion cards that they support. 2.6.1 Installing an expansion card Follow these steps to install an expansion card. 1. Before installing the expansion card, read the documen[...]

2-12 Chapter 2: Hardware information Standard Interrupt Assignments IRQ Priority Standard Function 0 1 System T imer 1 2 Keyboard Controller 2 N/A Programmable Interrupt 3* 1 1 Communications Port (COM2) 4* 12 Communications Port (COM1) 5* 13 Sound Card (sometimes LPT2) 6 14 Floppy Disk Controller 7* 15 Printer Port (LPT1) 8 3 System CMOS/Real T im[...]

ASUS PR-DLS533 motherboard user guide 2-13 2.6.3 PCI slots This motherboard implements the PCI-X (Peripheral Component Interconnect Extended) bus technology to support up to 133MHz data transfers, or about 1.06GB/s. This bus technology is primarily designed for servers to increase the performance of high bandwidth devices such as Gigabit Ethernet c[...]

2-14 Chapter 2: Hardware information 2.7 Switches and jumpers 2.7.1 Switches The following figure shows the location and default settings of the DIP switches on the motherboard. Keep the default settings for stable system operation. PR-DLS533 ON OFF ON OFF PR-DLS533 DIP Switches CLKSW ON 12345 (Default) CONFIG_SW ON 12345678 1. CPU external frequen[...]

ASUS PR-DLS533 motherboard user guide 2-15 2.7.2 Jumpers 1. CPU clock setting (3-pin CLKSEL) This jumper allows you to select the CPU frequency . Set to Auto (pins 1-2) to allow automatic frequency selection depending on the type of the installed CPU. Set to pins 2-3 if you installed a Foster 100MHz CPU. Remove the jumper cap to manually select the[...]

2-16 Chapter 2: Hardware information 2. 32-bit PCI Ethernet controller setting (3-pin LAN_SW) Set this jumper to pins 1-2 to enable the onboard Intel 82540EM 32-bit Gigabit Ethernet controller to support 10/100/1000 Mbps networking, or the Intel 82551QM Fast Ethernet controller to support 10BASE-T/ 100BASE-TX networking. Set to pins 2-3 to disable [...]

ASUS PR-DLS533 motherboard user guide 2-17 5. Clear RTC RAM (R452) These solder pads allow you to clear the Real T ime Clock (R TC) RAM in CMOS. Y ou can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The RAM data in CMOS, that include system setup information such as system passwords, is powered [...]

2-18 Chapter 2: Hardware information 2.8 Connectors This section describes and illustrates the internal connectors on the motherboard. Always connect ribbon cables with the red stripe to Pin 1 on the connectors. Pin 1 is usually on the side closest to the power connector on hard drives and CD-ROM drives, but may be on the opposite side on floppy di[...]

ASUS PR-DLS533 motherboard user guide 2-19 3. IDE connectors (two 40-1 pin PRI_IDE/SEC_IDE) This connector supports the provided UltraDMA/100/66 IDE hard disk ribbon cable. Connect the cable’s blue connector to the primary (recommended) or secondary IDE connector , then connect the gray connector to the UltraDMA/100/66 slave device (hard disk dri[...]

2-20 Chapter 2: Hardware information 4. Chassis alarm lead (4-1 pin CHASSIS) This lead is for a chassis designed with intrusion detection feature. This requires an external detection mechanism such as a chassis intrusion sensor or microswitch. When you remove any chassis component, the sensor triggers and sends a high-level signal to this lead to r[...]

ASUS PR-DLS533 motherboard user guide 2-21 6. A TX power connectors (24/20-pin A TXPWR, 8-pin A TX12V) These connectors connect to an A TX 12V power supply . The plugs from the power supply are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. In addition [...]

2-22 Chapter 2: Hardware information 7. CPU, Chassis, and Power Fan Connectors (3-pin CPUF AN1, CPUF AN2, SYSF AN1, SYSF AN2, SYSF AN3) The fan connectors support cooling fans of 350mA~740mA (8.88W max.) or a total of 1A~2.22A (26.64W max.) at +12V . Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of[...]

ASUS PR-DLS533 motherboard user guide 2-23 9. Zero Channel RAID slot (PCI-X5) The 64-bit/100MHz PCI-X slot (colored green) supports the LSI MegaRAID 320-0 or the Intel SRC ZCR (Zero-Channel RAID) card to provide advanced RAID functionality . The card supports RAID levels 0, 1, 5, multilevel 0/1 and 0/5, cache memory modules with ECC, and predictive[...]

2-24 Chapter 2: Hardware information 12. W ake-On-LAN Connector (3-pin WOL_CON) This connector supports a LAN card with a W ake-On-LAN output. The connector powers up the system when a wakeup packet or signal is received through the LAN card. 1 1. IPMI connector (4-pin IPMI) The Intelligent Platform Management Interface (IPMI) connector is for the [...]

ASUS PR-DLS533 motherboard user guide 2-25 13. T wo 68-pin Ultra320 SCSI Connectors (SCSI-A, SCSI-B) This motherboard has two 68-Pin Ultra320 SCSI connectors; one for each of the two channels. Each channel can support a maximum of 15 devices as specified by Ultra320 standards. SCSI Connection Notes This motherboard has two 68-Pin Ultra320 SCSI conn[...]

2-26 Chapter 2: Hardware information 14. W ake-On-Ring Connector (2-pin WOR) This connector connects to internal modem cards with a W ake-On- Ring output. The connector powers up the system when a ringup packet or signal is received through the internal modem card. For external modems, W ake-On-Ring is detected through the COM port. PR-DLS533 PR-DL[...]

ASUS PR-DLS533 motherboard user guide 2-27 • System Power LED Lead (3-1 pin PLED) This 3-1 pin connector connects to the system power LED. The LED lights up when you turn on the system power , and blinks when the system is in sleep mode. • System Message LED Lead (2-pin MLED) This 2-pin connector is for the system message LED that indicates rec[...]

2-28 Chapter 2: Hardware information[...]

Chapter 3 Powering up This chapter describes the power up sequence and gives information on the BIOS beep codes.[...]

ASUS PR-DLS533 motherboard Chapter summar y 3.1 Starting up for the first time .......................... 3-1 3.2 Powering off the computer ........................... 3-2[...]

ASUS PR-DLS533 motherboard user guide 3-1 3. 1 St ar ting up for t he firs t time 1. After making all the connections, replace the system case cover . 2. Be sure that all switches are off. 3. Connect the power cord to the power connector at the back of the system chassis. 4. Connect the power cord to a power outlet that is equipped with a surge pro[...]

3-2 Chapter 3: Powering up 3.2 Powering of f the com puter Y ou must first exit the operating system and shut down the system before switching off the power . For A TX power supplies, you can press the A TX power switch after exiting or shutting down the operating system. If you use Windows 95/98/2000/XP , click the Start button, click Shut Down, t[...]

Chapter 4 BIOS setup This chapter tells how to change system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.[...]

ASUS PR-DLS533 motherboard Chapter summar y 4.1 Managing and updating your BIOS .............. 4-1 4.2 BIOS Setup program ...................................... 4-5 4.3 Main Menu ...................................................... 4-8 4.4 Advanced Menu ........................................... 4-15 4.5 Power Menu ..............................[...]

ASUS PR-DLS533 motherboard user guide 4-1 4.1.1 Creating a bootable disk AFLASH.EXE is a Flash Memory W riter utility that updates the BIOS by uploading a new BIOS file to the programmable flash ROM on the motherboard. This file works only in DOS mode. T o determine the BIOS version of your motherboard, check the last four numbers of the code displ[...]

4-2 Chapter 4: BIOS Setup 5. Select 1. Save Current BIOS to File from the Main menu and press <Enter>. The Save Current BIOS T o File screen appears. 6. T ype a filename and the path, for example, A:XXX-XX.XXX, then press <Enter>.[...]

ASUS PR-DLS533 motherboard user guide 4-3 1. Download an updated ASUS BIOS file from the Internet (WWW or FTP) (see ASUS CONT ACT INFORMA TION on page x for details) and save to the boot floppy disk you created earlier . 2. Boot from the floppy disk. 3. At the “ A: ” prompt, type AFLASH and then press <Enter>. 4. At the Main Menu, type 2[...]

4-4 Chapter 4: BIOS Setup 7. The utility starts to program the new BIOS information into the Flash ROM. The boot block is updated automatically only when necessary . This minimizes the possibility of boot problems in case of update failures. When the programming is done, the message “Flashed Successfully” appears. 8. Follow the onscreen instruc[...]

ASUS PR-DLS533 motherboard user guide 4-5 4.2 BIOS Setup progr am This motherboard supports a programmable Flash ROM that you can update using the provided utility described in section “ 4.1 Managing and updating your BIOS. ” Use the BIOS Setup program when you are installing a motherboard, reconfiguring your system, or prompted to “ Run Setu[...]

4-6 Chapter 4: BIOS Setup 4.2.1 BIOS menu bar The top of the screen has a menu bar with the following selections: MAIN Use this menu to make changes to the basic system configuration. ADV ANCED Use this menu to enable and make changes to the advanced features. POWER Use this menu to configure power management features. BOOT Use this menu to configu[...]

ASUS PR-DLS533 motherboard user guide 4-7 General help In addition to the Item Specific Help window , the BIOS setup program also provides a General Help screen. Y ou may launch this screen from any menu by simply pressing <F1> or the <Alt> + <H> combination. The General Help screen lists the legend keys and their corresponding fu[...]

4-8 Chapter 4: BIOS Setup System Time [XX:XX:XX] Sets the system to the time that you specify (usually the current time). The format is hour , minute, second. V alid values for hour , minute and second are Hour: (00 to 23), Minute: (00 to 59), Second: (00 to 59). Use the <T ab> or <Shift> + <T ab> keys to move between the hour , m[...]

ASUS PR-DLS533 motherboard user guide 4-9 Supervisor Password [Disabled] / User Password [Disabled] These fields allow you to set passwords. T o set a password, highlight the appropriate field and press <Enter>. T ype in a password then press <Enter>. Y ou can type up to eight alphanumeric characters. Symbols and other characters are ig[...]

4-10 Chapter 4: BIOS Setup 4.3.1 Primary and Secondary Master/Slave T ype [Auto] Select [Auto] to automatically detect an IDE hard disk drive. If automatic detection is successful, Setup automatically fills in the correct values for the remaining fields on this sub-menu. If automatic detection fails, this may be because the hard disk drive is too o[...]

ASUS PR-DLS533 motherboard user guide 4-11 If no drive is installed or if you are removing a drive and not replacing it, select [None]. Other options for the T ype field are: [CD-ROM] - for IDE CD-ROM drives [LS-120] - for LS-120 compatible floppy disk drives [ZIP] - for ZIP-compatible disk drives [MO] - for IDE magneto optical disk drives [Other A[...]

4-12 Chapter 4: BIOS Setup T ranslation Method [LBA] Select the hard disk drive type in this field. When Logical Block Addressing (LBA) is enabled, the 28-bit addressing of the hard drive is used without regard for cylinders, heads, or sectors. Note that LBA Mode is necessary for drives with more than 504MB storage capacity . Configuration options:[...]

ASUS PR-DLS533 motherboard user guide 4-13 SMART Monitoring [Disabled] This field allows you to enable or disable the S.M.A.R.T . (Self-Monitoring, Analysis and Reporting T echnology) system that utilizes internal hard disk drive monitoring technology . This parameter is normally disabled because the resources used in the SMART monitoring feature m[...]

4-14 Chapter 4: BIOS Setup 4.3.2 Keyboard Features Boot Up NumLock Status [On] This field enables users to activate the Number Lock function upon system boot. Configuration options: [Off] [On] Keyboard Auto-Repeat Rate [6/Sec] This controls the speed at which the system registers repeated keystrokes. Options range from 6 to 30 characters per second[...]

ASUS PR-DLS533 motherboard user guide 4-15 4.4 Advanced Menu CPU Speed [Manual] This field displays the auto-detected CPU speed. CPU Level 1 Cache, CPU Level 2 Cache [Enabled] These fields allow you to choose from the default [Enabled] or choose [Disabled] to turn on or of f the CPU Level 1 and Level 2 built-in cache. Configuration options: [Disabl[...]

4-16 Chapter 4: BIOS Setup OS/2 Onboard Memory > 64M [Disabled] When using OS/2 operating systems with installed DRAM of greater than 64MB, you need to set this option to [Enabled]. Otherwise, leave to the default setting [Disabled]. Configuration options: [Disabled] [Enabled] USB Legacy Support [Auto] This motherboard supports Universal Serial [...]

ASUS PR-DLS533 motherboard user guide 4-17 4.4.1 Chip Configuration V ideo Memory Cache Mode [UC] USWC (uncacheable, speculative write combining) is a new cache technology for the video memory of the processor . It can greatly improve the display speed by caching the display data. Y ou must set this to UC (uncacheable) if your display card cannot s[...]

4-18 Chapter 4: BIOS Setup 4.4.2 I/O Device Configuration Floppy Disk Access Control [R/W] When set to [Read Only], this parameter protects files from being copied to floppy disks by allowing reads from, but not writes to, the floppy disk drive. The default setting [R/W] allows both reads and writes. Configuration options: [R/W] [Read Only] Onboard[...]

ASUS PR-DLS533 motherboard user guide 4-19 Parallel Port Mode [ECP+EPP] This field allows you to set the operation mode of the parallel port. [Normal] allows normal-speed operation but in one direction only; [EPP] allows bidirectional parallel port operation; [ECP] allows the parallel port to operate in bidirectional DMA mode; [ECP+EPP] allows norm[...]

4-20 Chapter 4: BIOS Setup 4.4.3 PCI Configuration Slot 1, Slot 2, Slot 3, Slot 4, Slot 5, Slot 6 IRQ [Auto] These fields set how IRQ use is determined for each PCI slot. The default setting for each field is [Auto], which utilizes auto-routing to determine IRQ use. Configuration options: [Auto] [NA] [3] [4] [5] [7] [9] [10] [1 1] [12] [14] [15] PC[...]

ASUS PR-DLS533 motherboard user guide 4-21 Onboard SCSI BIOS [Auto] [Auto] allows the motherboard BIOS to detect whether you have a Adaptec SCSI controller . If the SCSI controller is detected, the SCSI BIOS will be enabled. If no SCSI controller is detected, the onboard SCSI BIOS will be disabled. Setting to [Disabled] deactivates the onboard SCSI[...]

4-22 Chapter 4: BIOS Setup 4.5 Power Menu The Power menu allows you to reduce power consumption. This feature turns of f the video display and shuts down the hard disk after a period of inactivity . Power Management [User Defined] This field allows you to activate or deactivate the automatic power saving features. When set to [Disabled], the power [...]

ASUS PR-DLS533 motherboard user guide 4-23 V ideo Off Option [Suspend -> Off ] This field determines when to activate the video off feature for monitor power management. Configuration options: [Always On] [Suspend -> Off] V ideo Off Method [DPMS OFF] This field defines the video of f features. The Display Power Management System (DPMS) featur[...]

4-24 Chapter 4: BIOS Setup 4.5.1 Power Up Control AC PWR Loss Restart [Disabled] This allows you to set whether or not to reboot the system after power interruptions. [Disabled] leaves your system off while [Enabled] reboots the system. [Previous State] sets the system back to the state it was before the power interruption. Configuration options: [[...]

ASUS PR-DLS533 motherboard user guide 4-25 Power On By PS/2 Keyboard [Disabled] This parameter allows you to use specific keys on the keyboard to turn on the system. This feature requires an A TX power supply that provides at least 1A on the +5VSB lead. Configuration options: [Disabled] [Space Bar] [Ctrl-Esc] [Power Key] Automatic Power Up [Disable[...]

4-26 Chapter 4: BIOS Setup 4.5.2 Hardware Monitor MB Temperature [xxxC/xxxF] CPU1 Temperature [xxxC/xxxF] CPU2 Temperature [xxxC/xxxF] The onboard hardware monitor is able to detect the MB (motherboard) and CPU temperatures. Set to [Ignore] only if necessary . CPU1 Fan Speed [xxxxRPM] CPU2 Fan Speed [xxxxRPM] The onboard hardware monitor is able to[...]

ASUS PR-DLS533 motherboard user guide 4-27 4.6 Boot Menu The motherboard BIOS supports the BIOS Boot Specification (BBS) version 1.01. BBS is an intelligent mechanism that provides flexible ways to set boot sequence for Initial Program Load (IPL) devices such as CD-ROMs, network remote boot ROM, and SCSI or RAID controllers on PnP cards. The IPL de[...]

4-28 Chapter 4: BIOS Setup The BCV devices present in the system will appear as options for this field. The field shows [None] if no BCV device is installed. 3rd Boot : (BEV) [<0> Intel Corporation] This field allows you to select a Bootstrap Entry V ector (BCV) device to boot from. BEV devices include network controllers or cards. The BEV de[...]

ASUS PR-DLS533 motherboard user guide 4-29 Init Slot 1, 2, 3, 4, 5, 6 IRQ [Normal] This field allows you to set the priority level for each expansion slot in order to determine expansion card initialization order . Configuration options: [High] [Normal] [Low] [Skip] 4.6.1 Boot Configuration MPS 1.4 Support [Enabled] This field allows you to enable [...]

4-30 Chapter 4: BIOS Setup DRAM Hot Spare Memory [Disabled] This field allows you to allocate rows of SDRAM for hot spare. Configuration options: [Disabled] [1 row] [2 rows] [3 rows] Remote Console [Disabled] This field allows the text mode VGA display to be sent out to VT100 terminal through COM1. This function is ef fective at BIOS POST and DOS e[...]

ASUS PR-DLS533 motherboard user guide 4-31 4.8 Exit Menu When you have made all of your selections from the various menus in the Setup program, save your changes and exit Setup. Select Exit from the menu bar to display the following menu. Exit Saving Changes Once you are finished making your selections, choose this option from the Exit menu to ensu[...]

4-32 Chapter 4: BIOS Setup Load Setup Defaults This option allows you to load the default values for each of the parameters on the Setup menus. When you select this option or if you press <F5>, a confirmation window appears. Select [Y es] to load default values. Select Exit Saving Changes or make other changes before saving the values to the [...]

Chapter 5 Driver installation This chapter tells how to install SCSI, LAN, and VGA drivers under various operating systems.[...]

ASUS PR-DLS533 motherboard Chapter summar y 5.1 Support CD contents ..................................... 5-1 5.2 Microsoft Windows NT Server 4.0 ................ 5-3 5.3 Microsoft Windows 2000 Server ................. 5-13 5.4 Microsoft Windows XP Professional .......... 5-25 5.5 Novell NetW are Server ................................. 5-31 5.6 SC[...]

ASUS PR-DLS533 motherboard user guide 5-1 5. 1 Suppor t CD contents The support CD that came with the motherboard contains useful software and several utility drivers that enhance the motherboard features. T o begin using the support CD, simply insert the CD into your CD-ROM drive. The CD automatically displays the welcome screen and the installati[...]

5-2 Chapter 5: Driver installation 5.1.3 Utilities This screen displays the available system utilities that you can install. 5.1.4 Contact This screen displays the ASUS worldwide contact information.[...]

ASUS PR-DLS533 motherboard user guide 5-3 5.2 Microsof t ® Windows ® NT Ser ver 4.0 5.2.1 LSI ® SCSI Driver Installation Windows NT 4.0 does not have drivers for the new SCSI controllers, you must load the driver manually prior to Windows NT 4.0 installation. A. Preparing an LSI Driver Disk From the support CD, locate the LSI drivers in the foll[...]

5-4 Chapter 5: Driver installation B1. CD-ROM Installation 1. Have the driver diskette available for inserting into the A: drive when prompted. Depending upon the media used to distribute the drivers (web or CDROM), you will create a driver diskette. IMPOR T ANT : Read Steps 2 and 3 before performing the instructions contained within these steps. 2[...]

ASUS PR-DLS533 motherboard user guide 5-5 B2. Boot Floppy Disk Installation 1. Have the driver diskette available for inserting into the A: drive when prompted. Depending upon the media used to distribute drivers (web or CDROM), you will create a driver diskette. IMPOR T ANT : Read Step 2 before performing the instructions contained within this ste[...]

5-6 Chapter 5: Driver installation C. Existing System Installation T o install the SYMMPI.SYS miniport driver , follow these steps: 1. Boot Windows NT 4.0 and log on as Administrator . 2. Click on the Start button. Move to Settings-->Control Panel and click. 3. Double click on SCSI Adapters. 4. Click on the Drivers tab. 5. Click Add. A list of i[...]

ASUS PR-DLS533 motherboard user guide 5-7 5.2.2 Intel ® LAN Driver Installation A. Preparing the Intel LAN Driver Disk Windows NT 4.0 does not have the drivers for the Intel 82551QM/ 82540EM/82544GC LAN controllers. Before installing Windows NT 4.0, copy the LAN drivers from the support CD into a floppy disk. Prepare one blank formatted high densi[...]

5-8 Chapter 5: Driver installation B. New System Installation 1. Double-click the Network icon in the Control Panel to display the Network Setup Wizard. 2. When the Installing Windows NT Networking screen appears, press Next to display the following screen. 5. Insert the floppy disk into the floppy disk drive when prompted. 6. Follow the screen ins[...]

ASUS PR-DLS533 motherboard user guide 5-9 3. Check the Wired to the Network box, then click Next . 4. On the screen that appears, click the button Select from list... to display the Select Network Adapter window . 5. Insert the LAN driver disk that you created, then click Have Disk... 6. T ype A: in the dialog box that appears, then click OK. The [...]

5-10 Chapter 5: Driver installation 9. Click Select from list... , then click Have Disk... 10. T ype A: in the dialog box, then click OK. 1 1. In the following screen, select Intel(R) PRO/1000 Family Adapter , then click OK. Follow the succeeding screen instructions. 12. When done, the following screen appears showing the Intel(R) PRO/1000 Family [...]

ASUS PR-DLS533 motherboard user guide 5-11 C. Existing System Installation 1. Double-click the Network icon in the Control Panel. 2. Select the Adapter tab, then click Add . A list of adapters appears. 4. Do not select an adapter from the list. Instead, insert the LAN driver disk that you created from the support CD. Refer to the section “A. Prep[...]

5-12 Chapter 5: Driver installation 5.2.3 A TI ® Rage XL Display Driver Installation 1. Insert the support CD into your CD-ROM drive. 2. If Autorun in enabled in your computer , the following screen appears. Click on A TI Rage XL Display Driver to install the driver . If Autorun is disabled, install the display driver from the following path: Dri[...]

ASUS PR-DLS533 motherboard user guide 5-13 5.3 Microsof t ® Windows ® 2000 Ser ver 5.3.1 LSI ® SCSI Driver Installation Windows 2000 Server does not have drivers for the new SCSI controllers, you must load the driver manually prior to Windows 2000 Server installation. A. Preparing an LSI Driver Disk From the support CD, locate the LSI drivers in[...]

5-14 Chapter 5: Driver installation B1. CD-ROM Installation 1. Have the driver diskette available for inserting into the A: drive when prompted. Depending upon the media used to distribute the drivers (web or CDROM), you will create a driver diskette. IMPOR T ANT : Read Steps 2 and 3 before performing the instructions contained within these steps. [...]

ASUS PR-DLS533 motherboard user guide 5-15 B2. Boot Floppy Disk Installation 1. Have the driver diskette available for inserting into the A: drive when prompted. Depending upon the media used to distribute drivers (web or CDROM), you will create a driver diskette. IMPOR T ANT : Read Step 2 before performing the instructions contained within this st[...]

5-16 Chapter 5: Driver installation C. Existing System Installation T o install the SYMMPI.SYS miniport driver , follow these steps: 1. Boot Windows 2000 Server and log on as Administrator . 2. Click on the Start button. Move to Settings and click on Control Panel. 3. Double click on SCSI an RAID controllers to display the following window . 4. Cli[...]

ASUS PR-DLS533 motherboard user guide 5-17 14. After rebooting, check the installed SCSI driver from the Computer Management window . 15. Highlight the LSI Logic 1020/1030 Ultra320 SCSI Adapter , click the right mouse button, and select Properties to display the following.[...]

5-18 Chapter 5: Driver installation 16. Click Driver Details to display a list of files related to the SCSI driver .[...]

ASUS PR-DLS533 motherboard user guide 5-19 5.3.2 Intel ® LAN Driver Installation Y ou may install the Intel 82551QM/82540EM/82544GC LAN drivers directly from the support CD. Proceed to the section “B. Update LAN Driver on an Existing System Installation.” If you wish to create a LAN driver disk, proceed to the section “A. Preparing the Intel[...]

5-20 Chapter 5: Driver installation B. Update Driver on an Existing System Installation Y ou may update the LAN driver directly from the support CD. 1. Insert the support CD into the CD-ROM drive. On the screen that appears, click on Intel PRO/100 LAN Driver , then on the item Install Base Driver . 2. Follow the screen instructions to complete the [...]

ASUS PR-DLS533 motherboard user guide 5-21 When done, your Computer Management window shows the installed LAN adapters. 3. Highlight the Intel(R) 82540EM-based Network Connection , click the right mouse button, and select Properties to display the following. 4. Click Driver Details to display a list of the files related to the Intel 82540EM LAN dri[...]

5-22 Chapter 5: Driver installation 5. Highlight the Intel(R) 82544GC-based Network Connection , click the right mouse button, and select Properties to display the following.[...]

ASUS PR-DLS533 motherboard user guide 5-23 Y ou may also update the LAN drivers from the LAN Driver Disk if you created one. Follow these steps to update from the LAN driver disk. 1. Boot Windows 2000 system and log on as Administrator . 2. Click on the Start button. Select Settings , then Control Panel . 3. Double-click the System icon in the Cont[...]

5-24 Chapter 5: Driver installation 5.3.4 Enabling A T A100 Feature in Windows ® 2000 T o enable the A T A100 feature under Windows 2000, you need to upgrade to Windows 2000 Service Pack 2 or later . 5.3.3 A TI ® Rage XL Display Driver Installation Windows 2000 system can automatically recognize the A TI RAGE XL PCI driver during system installat[...]

ASUS PR-DLS533 motherboard user guide 5-25 5.4 Microsof t ® Windows ® XP Pr ofessional 5.4.1 LSI ® SCSI Driver Installation Windows XP Professional does not have drivers for the new SCSI controllers. Y ou must load the driver manually prior to Windows XP installation. A. Preparing an LSI Driver Disk From the support CD, locate the LSI drivers in[...]

5-26 Chapter 5: Driver installation B1. CD-ROM Installation 1. Start the Windows XP installation by booting from the Windows XP CD-ROM. The system BIOS must support booting from a CD-ROM. BIOS settings may need to be changed to allow CD-ROM booting. 2. Press the F6 key to install the SYMMPI.SYS driver when the screen displays “ Windows Setup. ”[...]

ASUS PR-DLS533 motherboard user guide 5-27 C. Existing System Installation This procedure installs or upgrades the SYMMPI.SYS drivers onto an existing Windows XP system. NOTE: When a LSI Logic SCSI or Fibre Channel adapter is added to an existing system installation, the new adapter is automatically detected at the next reboot. When the Device Driv[...]

5-28 Chapter 5: Driver installation 13. Click STOP Installation to cancel the installation if a nonsigned driver is not desired. - or - Click Continue Anyway to continue the installation. The system will load the driver from the Windows XP driver diskette. A message box may display indicating that the target (existing) driver is newer than the sour[...]

ASUS PR-DLS533 motherboard user guide 5-29 For Windows XP Professional users, we recommended that you use the Intel 82551QM/82540EM/82544GC driver from the support CD. A. Preparing the Intel LAN Driver Disk 1. Insert the support CD into the CD-ROM drive. 2. Run the utility from the following path: DriversLANMAKEDISKdcreate.exe 3. In the followi[...]

5-30 Chapter 5: Driver installation 5. Follow the succeeding installation instructions. 6. When done, the following screen appears. Click Finish to complete the installation.[...]

ASUS PR-DLS533 motherboard user guide 5-31 5.5 Novell ® NetWare ® Ser ver 5.5.1 LSI ® SCSI Driver Installation A single driver (*HAM) is provided for the Novell NetW are 5.1/6.0 environments. This document explains how to install and use the SDMS NWP A SCSI Host Adapter Module (HAM) driver for NetW are. A. Preparing an LSI Driver Disk From the s[...]

5-32 Chapter 5: Driver installation 3. Next the system prompts the user with the available command line options to load the driver . A description of each option appears in the box at the bottom of the installation screen. A more detailed description is given in the section titled Command Line Options. Modify any option values as needed. 4. Load a [...]

ASUS PR-DLS533 motherboard user guide 5-33 5.5.2 Intel ® LAN Driver Installation Y ou may install the Intel 82551QM/82540EM/82544GC LAN drivers directly from the support CD. Proceed to the section “B. Update LAN Driver on an Existing System Installation.” If you wish to create a LAN driver disk, proceed to the section “A. Preparing the Intel[...]

5-34 Chapter 5: Driver installation B. NetW are 5.1/6.0 Installations 1. From the NetW are console, type NWCONFIG or Load Install and press <Enter>. 2. From the Configuration Options screen, choose Driver options and press <Enter>. 3. Choose Configure network drivers and press <Enter>. If any drivers are already loaded, a list of [...]

ASUS PR-DLS533 motherboard user guide 5-35 5.5.3 A TI ® Rage XL Display Driver Installation Y ou can select the “ Super VGA ” for the X Server on NetW are 5 server system. The other NetW are system didn ’ t support X Server and you didn ’ t need the VGA driver support. 7. The driver name is displayed: Intel(R) PRO PCI adapter . Press <E[...]

5-36 Chapter 5: Driver installation 5.6 SCO OpenSer ver 5.0.6a 5.6.1 LSI ® SCSI Driver Installation A. Building the SCO OpenServer BTLD Diskette T o create a BTLD diskette for SCO OpenServer system, copy the raw dd image file onto a 1.44MB floppy disk. This process is dependent upon the operating system that you are using to create this diskette. [...]

ASUS PR-DLS533 motherboard user guide 5-37 B. New System Installation This procedure installs SCO UNIX onto a hard disk drive. This installation is necessary to build a new UNIX kernel that includes your SDMS driver . During installation, you are given the option of retaining current partitions on the root hard disk. For instance, you could have a [...]

5-38 Chapter 5: Driver installation C. Existing System Installation This procedure assumes SCO UNIX is already installed on a hard disk drive. This installation is necessary to build a new UNIX kernel that includes the proper LSI host adapter driver . The basic steps for accomplishing this are outlined below . For more details on UNIX installation,[...]

ASUS PR-DLS533 motherboard user guide 5-39 7. T o activate the new kernel, you must reboot the system. At the command prompt, type: reboot Press Enter . C2. Adding a SCSI Disk Drive NOTE: If you are not adding a SCSI or Fibre Channel disk drive to this system, go to step 4. 1. At the command prompt, type: mkdev hd Press Enter . 2. The system prompt[...]

5-40 Chapter 5: Driver installation 7. The system prompts you to update the Configuration file. T ype y and press Enter if the displayed values are correct. T ype n if the values are incorrect, and retry from step 3d. 8. A prompt appears to create a new kernel. T ype y if this is the last device to be added, or type n if additional devices are to b[...]

ASUS PR-DLS533 motherboard user guide 5-41 7. With SCO OpenServer 5.0.6a, the system prompts for the bus number of the tape drive. Since LSI Logic host adapters support only one bus per adapter , press Enter to get the default of zero, or type 0 (zero) and press Enter . 8. The system prompts for the ID of the tape drive. T ype the ID number of the [...]

5-42 Chapter 5: Driver installation 5. The system prompts for the host adapter that supports the CD-ROM drive. T ype the correct host adapter number and press Enter . If an additional LSI Logic host adapter is being added to the SCO UNIX kernel, the system may prompt if you want to update the link-kit (add another host adapter). T ype y and press E[...]

ASUS PR-DLS533 motherboard user guide 5-43 C5. Rebuilding the Kernel 1. T o rebuild the kernel, type: /etc/conf/cf.d/link_unix 2. The system displays will prompt for responses to these messages: a. Do you want this kernel to boot by default (y/n)? T ype: y Press Enter . The system backs up the old kernel. b. Do you want the kernel environment r ebu[...]

5-44 Chapter 5: Driver installation 5.7 SCO UnixW are Ser ver 5.7.1 LSI ® SCSI Driver Installation A. Building the LSI Logic Fusion-MPT ™ mpt Driver HBA Diskette This is the guide to create an HBA driver diskette for the the Caldera UnixW are 7 and Open Unix 8 Operating Systems. Both of these operating systems will hereafter be referred to as ?[...]

ASUS PR-DLS533 motherboard user guide 5-45 2. The dd image is located in the zipped file you downloaded from the LSI Logic web site. 3. RA WRITE3.COM is included within the zipped file you downloaded from the LSI Logic web site. After the image has been copied to a 3.5 diskette, use this HBA diskette for UnixW are installations as instructed. B. Ne[...]

5-46 Chapter 5: Driver installation 5. Select the mpt package. The mpt driver on this diskette is then loaded onto the system. The system will again prompt you to load a driver even if loading was successful. 6. T ype q (quit) and press Enter . 7. V erify that the driver is now loaded successfully by typing: pkginfo mpt 8. The package information s[...]

ASUS PR-DLS533 motherboard user guide 5-47 5.7.2 Intel ® LAN Driver Installation SCO UnixW are 7.1.1 system can correctly recognize Intel 82551QM/ 82540EM/82544GC network controller during installation. Y ou don ’ t need to load or modify the network driver for the onboard LAN device. Locate the Intel 82551QM/82540EM/82544GC network driver from [...]

5-48 Chapter 5: Driver installation 5.8 Linux RedHat 7 .3/8.0 5.8.1 LSI ® SCSI Driver Installation The The Fusion-MPT driver is a bundled boot controller for RedHat 7.3/ 8.0. Y ou may install to a disk attached to the controller with no additional media. For more information on the LSI 53C1030 SCSI controller , refer to the following path in the s[...]