Aquapro Fish Feeders ADF-150DX инструкция обслуживания

Model# AdF-150dX Product Informa tIon GuIde 40 Gallon DIRECTIONAL fIsh fEEDER sYs TEM[...]

INCLUDED P ARTS 1) Hopper Assembly including Lid (3 Pieces) Poly Barrel Lid Poly Barrel Upper Poly Barrel Funnel 2) Directional Pow er Control Unit - assembly and programming instructions for this unit are contained within its box (1 piece) 3) Leg Kit (15 pieces) Poly Barrel Leg/ Hardw are/Bolt Kit Silicone Rubber Gasket (1 piece) P AGE 2[...]

1) Pliers 2) 1⁄4” Wrench 3) 5/32” Wrench 4) #8 Nut Driver (Hand held or for Cordless Drill) 5) Cordless Drill – If Necessar y 5/32” W asher (7 pieces) REQUIRED TOOLS P AGE 3 Latch and striker Hinge with pole and cotter pin 1⁄4” x 1” Bolt (10 pieces) 1⁄4” W asher (10 pieces) 1⁄4” Nylon Lock Nut (10 pieces) 5/32”x15/32” Bo[...]

ASSEMBL Y INSTRUCTIONS 1 V erify the contents of the package against the included par ts list. If you are missing any par ts from the list, please contact BA Products immediately at the toll-free number provided. 2 Fir st, remo ve the lid and two hopper assembly pieces and then place the three pieces on the ground. 3 Second, remove both the pow er [...]

7 Locate the hinge and install it with the rounded loops facing aw ay from the feeder . Use the 5/32” x 15/32” Bolts and 5/32” W ashers. Place the bolt head on top and the thread por tion toward the bottom on the inside of the hopper . Install the 5/32” Nylon Lock Nuts and tighten securely (Illustration C). 8 Place the lid on top of the hop[...]

P AGE 6 (Illustration F) (Illustration G) 9 Close the lid and then locate the latch and striker . Fir st, take the strik er por tion and install it onto the lid with the j-lip facing upward. These holes are already in place on the lid so install the 5/32” x 15/32” Bolts and the 5/32” W ashers with the heads on the outside of the hopper and th[...]

10 Once the hopper is assembled, make sure that the latch is closed and lay the hopper on its side. Next, locate the square tubing stub leg kit (3 pieces) and unwrap. T ake one stub leg and locate the recessed cavities on the funnel portion of the hopper . Place the stub leg into any ca vity so as it fits snug. Make sure that the stub leg is angle[...]

14 With the hopper lying on its side, take one full extension leg section and slide it into the square stub leg that you have already installed on the hopper (Illustration J). 15 Repeat step #14 for the remaining two extension leg sections. 16 Once all extension leg sections are installed into the stub legs, locate a second per son to help raise th[...]

P AGE 9 Once a suitable, level location for the feeder is identified and the unit is properly erected, open lid and fill container with feed/seed to desired capacity , ne ver to exceed 150 lbs. Once done, close the lid and lock the latch securely to insure it does not come off in the event of high winds, etc. This unit is designed to be used prim[...]

BA Products is not responsible for damage, expense or injur y caused by the unauthorized use of, alterations to, improper connection of and abuse or neglect of the BA Products’ feeder system. Never lean a ladder against the feeder when filling. Y ou must alwa ys use an alternative method to fill your feeder . The use of a ladder , or some other[...]

P AGE 11 The AquaPro ® Model #ADF-150 is loaded with features that you can not find anywhere else, such as a domed lid to effectively shed water , a built-in funnel to more efficiently focus feed to the power control unit, a unique low-profile design to protect against the feeder being top-heavy once filled, Polyprop ylene enforced constr ucti[...]

BA P roduct s 602 Fou nta in Par kw ay , Gr and Pr air ie, T exas 75 050 T el epho ne: (800) 8 47 - 826 9. F a x: (972) 352- 66 33 www .aquaprofishfeeder s.com[...]