Apple WS 6150 инструкция обслуживания

Service Source K Po wer Macintosh 6100/ WS 6150 Power Macintosh 6100/60, 6100/60AV, 6100/66, 6100/66AV, 6100/DOS Compatible, and Workgroup Server 6150[...]

Service Source K Basics Po wer Macintosh 6100/WS 6150[...]

Basics Power Macintosh System Overview - 1 Power Macintosh System Overview PowerPC microprocessors are a family of processors built on reduced instruction-set computing (RISC) technology. RISC processors streamline the internal workings of computers. Whereas traditional (complex instruction-set computing, or CISC) processors contain a wide variety [...]

Basics Power Macintosh System Overview - 2 Previously, RISC technology had been used only in high-end workstations and commercial database servers. With the introduction of Macintosh PowerPC computers, Apple succeeded in bringing RISC technology to personal computing. K ey Points Three key points to remember about a PowerPC processor- based Macinto[...]

Basics Power Macintosh System Overview - 3 Compatibility is not limited just to applications. INITs, CDEVs, drivers, and other Macintosh utility software also work on PowerPC processor-based Macintosh systems. So do AppleTalk devices (such as printers), SCSI devices (such as hard drives and scanners), ADB devices (such as mice, trackballs, and keyb[...]

Basics Power Macintosh System Overview - 4 of the fastest 68040- and 80486-based personal computers, the real promise of PowerPC technology is that it enables Apple and other developers to deliver new software capabilities on Macintosh systems that were previously available only on high-end workstations. T r oubleshooting Tips When troubleshooting [...]

Basics Power Macintosh System Overview - 5 provided in the Symptom Charts section of the Troubleshooting chapter under the “System” topic heading. 3 If a Power Macintosh system has bad RAM SIMMs installed, you will not hear death chimes. Instead, a dialog box will appear alerting you to the fact that a bad RAM SIMM has been detected. Additional[...]

Basics Power Macintosh System Overview - 6 5 The Power Macintosh AV systems use the same logic board as the non-AV versions. The only difference is that the AV versions have the Power Macintosh AV Card installed in the PDS slot. The Power Macintosh 7100/66 and 8100/80 systems must have a video card installed in the PDS slot. The Power Macintosh 710[...]

Basics HDI-45 Pinouts - 7 HDI-45 Pinouts This section includes an illustration of the HDI-45 connector and a table containing the pinout descriptions. Figure: HDI-45 Connector on the Logic Board[...]

Basics HDI-45 Pinouts - 8 T ab le: HDI-45 Pinouts Pin Description 1 Analog audio ground 2 Audio input shield 3 Left channel audio input 4 Right channel audio input 5 Left channel audio output 6 Right channel audio output 7 Reserved 8 Monitor ID sense line 1 9 Monitor ID sense line 2 (continued)[...]

Basics HDI-45 Pinouts - 9 10 Green ground (shield) 1 1 Green video output (75Ω) 1 2 Video input power ground 13 Power for camera +5 V 1 4 Reserved 1 5 Reserved 1 6 Reserved 1 7 Reserved 18 Monitor ID sense line 3 19 S-video input shield 20 S-video input luminance (Y) Pin Description (continued)[...]

Basics HDI-45 Pinouts - 1 0 21 S-video input chroma (C) 2 2 Reserved 2 3 Reserved 2 4 Reserved 2 5 Reserved 26 Red ground (shield) 2 7 Red video output (75Ω) 28 I 2 C data signal 29 I 2 C clock signal 3 0 Reserved 31 Monitor ID Pin Description (continued)[...]

Basics HDI-45 Pinouts - 1 1 32 Monitor ID 33 Vertical sync signal 3 4 Composite sync signal 3 5 ADB power +5 V 3 6 ADB ground 3 7 ADB data 3 8 Keyboard switch 3 9 Reserved 4 0 Reserved 41 Monitor ID 42 Horizontal sync signal Pin Description (continued)[...]

Basics HDI-45 Pinouts - 1 2 4 3 Video sync ground 44 Blue ground (shield) 45 Blue video output (75Ω) Pin Description[...]

Basics Rear Panel Connectors - 1 3 Rear Panel Connectors The figure on the following page shows the rear panel of a Power Macintosh 6100/60AV computer. The Workgroup Server and other non-AV versions of this machine would not include the S-Video In, DB-15 Video, and S-Video Out ports, which are actually part of the AV Card.[...]

Basics Rear Panel Connectors - 1 4 P ower Macintosh 6100/60 A V Rear P anel S-Video In DB-15 Video S-Video Out Ethernet SCSI HDI-45 Video Printer Modem ADB Sound Out Sound In Reset/ Interrupt[...]

Basics Logic Board Connectors - 1 5 Logic Board Connectors The figure on the following page shows a Power Macintosh 6100 Series logic board.[...]

Basics Logic Board Connectors - 1 6 Sound In Sound Out ADB Serial Ports AV Display Connector SCSI Ethernet DRAM SIMMs Soldered DRAM 601 Chip ROM Cache 601 PDS[...]

Basics Apple RAID Software - 1 7 Apple RAID Software Apple RAID (Redundant Array of Independent Disks) software protects data from loss during a disk failure and enhances the speed of data storage and retrieval. It is available for all Power Macintosh Workgroup servers. Data protection is achieved through disk mirroring, a data storage scheme in wh[...]

Basics Apple RAID Software - 1 8 • If you wish to use your server's startup disk for Apple RAID, do not install the Apple RAID program on your startup disk until you have initialized and set up new volumes on that disk. Before you initialize the startup disk, back up all valuable data. • You must reinitialize all disks on which you will us[...]

Basics Apple RAID Software - 1 9 back up your system files now. Back them up in such a way that you can restore your system files separately from the nonsystem files on your disk. You will later restore your system files using the backup copy rather than the System Installer on the RAID CD, so that you preserve your system customizations.[...]

Service Source K Specifications Po wer Macintosh 6100/WS 6150[...]

Specifications Processor - 1 Processor CPU 6100/60 & 6150: 60 MHz PowerPC 601 RISC microprocessor Built-in MMU and FPU 32K of on-chip cache memory Requires system software version 7.1.2 or later 6100/66 & 6150/66: 66 MHz PowerPC 601 RISC microprocessor Built-in MMU and FPU 32K of on-chip cache memory Requires system software version 7.5 or [...]

Specifications Memory - 2 Memory RAM 6100/60 & 6150: 8 MB RAM soldered on board; expandable to 72 MB via 2 SIMM sockets on logic board (requires a pair of same size, 80 ns or faster, 72-pin, noncomposite SIMMs); 16 MB configuration has two 4 MB SIMMs installed 6150/66: 16 MB RAM standard (8 MB soldered on board and two 4 MB SIMMs); expandable t[...]

Specifications Memory - 3 RO M 4 MB installed on SIMM socket VRAM 6100/60, 6100/66, 6150 & 6150/66: None 6100/60A V & 6100/ 66A V : 2 MB on Power Macintosh AV Card Cache 6100/60 & 6150: 32K of on-chip cache; optional 256K level 2 cache available 6100/66: 32K of on-chip cache; 256K level 2 cache standard Clock/Calendar CMOS custom chip w[...]

Specifications Disk Storage - 4 Disk Storage Floppy Drive 1.4 MB Apple SuperDrive Manual Insert Hard Drive 6100/60: 160 MB or 250 MB hard drive 6100/66: 350 MB or 500 MB hard drive 6150/66: 700 MB hard drive[...]

Specifications Disk Storage - 5 CD-R OM Drive 6100/60: Optional internal CD-ROM drive 6100/60A V : Internal AppleCD 300 Plus CD-ROM drive 6100/66 & 6100/ 66A V : Internal AppleCD 300 Plus CD-ROM drive standard on some models and optional on others 6150/66: Internal AppleCD 600 CD-ROM drive standard[...]

Specifications I/O Interfaces - 6 I/O Interfaces SCSI One SCSI port; DB-25 connector Supports a maximum of six external SCSI devices (five when CD- ROM is installed) Serial Two RS-232/RS-422 LocalTalk/GeoPort serial ports; mini DIN- 9 connectors (backward compatible with mini DIN-8 connectors) A pple Desktop Bus One Apple Desktop Bus (ADB) port; mi[...]

Specifications I/O Interfaces - 7 Expansion Slot 6100/60, 6100/66, 6150 & 6150/66: Internal expansion slot supports either a processor-direct slot card or 7-in. NuBus card (with appropriate adapter) 6100/60A V & 6100/ 66A V : Units ship with Power Macintosh AV card installed in the internal expansion slot Ethernet One built-in AUUI-15 Ether[...]

Specifications I/O Interfaces - 8 Sound (continued) Bandwidth: 20 Hz–20 kHz (± 2 dB) at 44.100 kHz sample rate THD+N (total harmonic distortion plus noise): less than 0.05%, measured 20Hz–20kHz with a 1-Vrms sine wave input V ideo 6100/60, 6100/66, 6150 & 6150/66: One HDI-45 DRAM-based video port on logic board supports direct connection t[...]

Specifications I/O Interfaces - 9 V ideo (continued) 6100/60A V & 6100/ 66A V : One HDI-45 DRAM-based video port on logic board supports direct connection to Apple AudioVision monitors; and, with HDI-45 to DB-15 adapter (which is included), these computers support 12", 13", 14", 15" portrait, 16", and 17" monitors;[...]

Specifications I/O Devices - 1 0 I/O De vices K eyboard Standard, extended, or adjustable keyboard Keyboard draws 25–80 mA, depending on model of keyboard Mouse ADB Mouse II; Draws up to 10 mA Microphone 6100/60, 6150 & 6150/ 66: Optional Apple PlainTalk microphone; unidirectional and optimized for use with speech recognition 6100/60A V , 610[...]

Specifications Video Display - 1 1 V ideo Display V ideo Display All Power Macintosh 6100 series computers support monochrome, color, VGA, and SVGA formats on the HDI-45 connector, including: • Macintosh 12" Monochrome Display (640 x 480) • Macintosh 12" RGB Display (512 x 384) • AppleColor High-Res RGB 14" Monitor (640 x 480) [...]

Specifications Video Display - 1 2 V ideo Display (continued) In addition, the AV versions support (via the DB-15 connector) • Macintosh 19" Color Display (1024 x 768) • Apple Multiple Scan 20 Display (1152 x 870) • Macintosh 21" Color Display (1152 x 870) • NTSC (512 x 384 and 640 x 480) • PAL (640 x 480 and 768 x 576)[...]

Specifications Electrical - 13 Electrical A/C Line Input V oltage 100–240 VAC; RMS single phase, automatically configured Input Line Frequency 50–60 Hz Input Po wer 132 W maximum continuous, 201 W peak input (not including monitor power) Po wer Supply DC Output 86 W continuous output[...]

Specifications Physical - 14 Physical Dimensions Height: 3.4 in. (85 mm) Width: 16.3 in. (415 mm) Depth: 15.6 in. (399 mm) W eight 14.0 lb. (6.4 kg), weight varies depending on internal devices installed[...]

Specifications Environmental - 15 En vironmental Operating T emperatur e 10–40° C (50–104° F) Storage T emperatur e –40 to 47° C (–40 F to 116.6° F) Relative Humidity 5–95% (noncondensing) Altitude 0–3,048 m (0–10,000 ft.)[...]

Service Source K Troubleshooting Power Macintosh 6100/WS 6150[...]

Troubleshooting General - 1 General The Symptom Charts included in this chapter will help you diagnose specific symptoms related to your product. Because cures are listed on the charts in the order of most likely solution, try the first cure first. Verify whether or not the product continues to exhibit the symptom. If the symptom persists, try the [...]

Troubleshooting Symptom Charts/ Power Supply - 2 Symptom Charts Power Supply System does not power up 1 Reset logic board. (Refer to Additional Procedures.) 2 Reseat ROM SIMM and cache SIMM. 3 Replace power supply. 4 Replace logic board.[...]

Troubleshooting Symptom Charts/ System - 3 System System intermittently crashes or hangs 1 Verify that system software is version 7.1.2 or later (6100/60 & 6150) or 7.5 or later (6100/66 & 6150/66). 2 Verify SIMMs are noncomposite and installed in like pairs (same size/speed). 3 Verify that software is known-good. 4 Verify that software is [...]

Troubleshooting Symptom Charts/ Video - 4 Video Screen is dark, audio and at least one drive operate, fan is running, and LED is lit 1 Adjust brightness on monitor. 2 Replace video cable. 3 Replace monitor. Refer to appropriate monitor manual to troubleshoot defective monitor. 4 Replace logic board. Retain customer’s SIMMs. Screen is dark, audio [...]

Troubleshooting Symptom Charts/ Video (Continued) - 5 Video (Continued) Partial or whole screen is bright and audio is present, but no video information is visible 1 Replace video cable. 2 Replace monitor. Refer to appropriate monitor manual to troubleshoot defective monitor. 3 Replace logic board. Retain customer’s SIMMs. Screen is completely da[...]

Troubleshooting Symptom Charts/ Video (Continued) - 6 Video (Continued) Multiple Scan monitor attached to Power Macintosh 6100/60AV displays ghosting or video smearing Replace Power Macintosh AV Card.[...]

Troubleshooting Symptom Charts/ Floppy Drive - 7 Floppy Drive Audio and video are present, but internal floppy drive does not operate 1 Replace internal floppy drive cable. 2 Replace internal floppy drive. 3 Replace logic board. Retain customer’s SIMMs. Floppy disk ejects, and display shows Mac icon with blinking “X” 1 Try a different floppy [...]

Troubleshooting Symptom Charts/ Floppy Drive (Continued) - 8 Floppy Drive (Continued) Floppy drive attempts to eject disk but doesn’t 1 Push floppy disk completely in. 2 Eject floppy disk manually. 3 Replace floppy drive. 4 Reseat or replace top housing assembly.[...]

Troubleshooting Symptom Charts/ Hard Drive - 9 Hard Drive Internal hard drive runs continuously 1 Update driver software of hard drive using HD-SC Setup. (Note: Use Apple RAID to update driver on RAID WS 6150 drives.) 2 Reinstall system software. 3 Replace SCSI data cable. 4 Replace hard drive. (Note: If replacing an Apple WS 6150 RAID drive, you m[...]

Troubleshooting Symptom Charts/ CD-ROM Drive - 10 CD-ROM Drive CD-ROM drive does not accept a compact disc 1 Exchange disc (if disc is dirty or damaged). 2 Replace CD-ROM drive mechanism. 3 Replace SCSI data cable. Macintosh does not display CD-ROM drive icon 1 Verify that CD-ROM extension is in System Folder. 2 Replace CD-ROM drive mechanism. 3 Re[...]

Troubleshooting Symptom Charts/ CD-ROM Drive (Continued) - 1 1 CD-ROM Drive (Continued) Computer with 600i CD-ROM drive makes stuttering sounds when playing CD+ or CD-R formatted discs or CD-ROM disc won’t mount Replace CD-ROM drive.[...]

Troubleshooting Symptom Charts/ Peripheral - 1 2 Peripheral Works with internal or external SCSI device, but does not work with both 1 Replace external SCSI cables. 2 Verify that there is only one terminator on external devices. 3 Verify that SCSI select switch on any external device is set differently from any internal SCSI device. 4 Verify that h[...]

Troubleshooting Symptom Charts/ Peripheral (Continued) - 1 3 Peripheral (Continued) Cursor does not move 1 Reboot computer. 2 Verify that mouse is connected properly. 3 If mouse was connected to keyboard, connect mouse to computer ADB port instead. If mouse works, replace keyboard. 4 If mouse does not work in any ADB port on computer, replace mouse[...]

Troubleshooting Symptom Charts/ Peripheral (Continued) - 1 4 Peripheral (Continued) Double-click does not open application, disk, or server 1 Remove duplicate system files from hard drive. 2 Clear parameter RAM. Hold down <Command> <Option> <P> <R> during startup but before “Welcome to Macintosh” appears. 3 If mouse was [...]

Troubleshooting Symptom Charts/ Miscellaneous - 15 Miscellaneous About This Macintosh reports more memory than is installed 1 Verify that RAM SIMMs are installed in matching pairs (same size and speed). 2 Replace RAM SIMMs. About This Macintosh reports less memory than is installed 1 Verify that RAM SIMMs are installed in matching pairs (same size [...]

Troubleshooting Symptom Charts/ Miscellaneous (Continued) - 1 6 Miscellaneous (Continued) Stack Overflow Errors in DOS/ Windows Environment If you encounter intermittent manual overflow errors when using the DOS Compatibility card, remove the card and make sure the jumper is in the “SX” position (over the two right-most prongs). Screen at bootu[...]

Troubleshooting Symptom Charts/ Global Village Modem “Busy Serial Port” - 17 Global Village Modem “Busy Serial Port” Using modem gives message: “Can’t find or can’t access a modem to use for registration. Make sure you have Global Village software installed correctly, reboot your computer, and try again. If you want to use a specific [...]

Troubleshooting Symptom Charts/ Global Village Modem “Busy Serial Port” - 18 Global Village Modem “Busy Serial Port” Resetting modem in TelePort Control Panel gives message: “The current port is busy and cannot be opened. Quit any open communication application, or turn off AppleTalk in the Chooser (if the modem is connected to the Printe[...]

Service Source K T ake Apart Po wer Macintosh 6100/WS 6150[...]

Take Apart Top Housing - 1 Top Housing No preliminary steps are required before you begin this procedure. Top Housing[...]

Take Apart Top Housing - 2 1 Press up o n the tabs at the back of the top housing. 2 Tilt the back of the top housing and remove it from the bottom housing. Tabs[...]

Take Apart Power Supply - 3 Power Supply Before you begin, remove the top housing. Caution : Review the ESD precautions in Bulletins/ Safety. Power Supply[...]

Take Apart Power Supply - 4 1 Remove the screw that secures the power supply. Power Supply[...]

Take Apart Power Supply - 5 2 For e asier access to the power supply, release the tabs of the floppy drive and slide the floppy drive forward a few inches. Note: If a CD-ROM drive is present, remove the SCSI data cable and move the CD-ROM drive forward. Refer to the CD-ROM drive topic. Tab Floppy Drive[...]

Take Apart Power Supply - 6 3 Disconnect these power supply cables • Main power cable • Hard drive power cable • CD-ROM drive power cable (if installed) Main Power Cable CD-ROM Drive Power Cable Hard Drive Power Cable[...]

Take Apart Power Supply - 7 4 Slide the power supply forward slightly. Power Supply[...]

Take Apart Power Supply - 8 5 Tilt the front of the power supply and lift it ou t of the computer. Replacement Note: Move the floppy drive forward. Press the actuator toward the back of the computer to properly seat the power switch in the actuator. Power Switch[...]

Take Apart Logic Board - 9 Logic Board Before you begin, remove the following: • Top housing • Power supply (optional) Caution: Review the ESD precautions in Bulletins/ Safety. Note: If removing the logic board from a 6100/60AV, you must first remove the Power Macintosh AV Card. Refer to “Expansion Cards” in the Upgrades chapter for more in[...]

Take Apart Logic Board - 1 0 1 Disconnect these cables from the logic board: • SCSI data cable • Speaker cable • LED cable • CD-ROM audio cable (if present) • Floppy drive cable Note: Lift the front edge of the logic board to make removing the floppy drive easier. 2 Slide forward the hard drive and CD-ROM drive (if installed). Ê Floppy D[...]

Take Apart Logic Board - 1 1 3 Remove the customer’s RAM SIMMs and 256K cache SIMM before returning the logic board to Apple. Note: Grasp the cache SIMM by its corners and pull up firmly to remove it. Standoff with Internal Screw[...]

Take Apart Logic Board - 1 2 Note: The connectors for the cache and ROM SIMMs are functionally the same, and the ROM and 256K cache SIMMs may be installed in either connector. Be sure you remove the cache SIMM and not the ROM SIMM. The 256K cache SIMM has five chips on each side. 4 Using a long Phillips screwdriver, remove the screw from the center[...]

Take Apart Logic Board - 1 3 5 Remove the Phillips screw from the front edge of the logic board. 6 Slide the logic board toward the front of the computer. Logic Board[...]

Take Apart Logic Board - 1 4 7 Remove the logic board. Replacement Note: Slide the hard drive and optional CD-ROM drive forward. Connect the floppy drive cable before replacing the logic board. Logic Board[...]

Take Apart DOS Compatibility Card - 15 DOS Compatibility Card Before you begin, remove the top housing. Caution : Review the ESD precautions in Bulletins/ Safety. Note: The DOS Compatibility card is an optional upgrade for the Power Macintosh 6100 Series computers. DOS Compatibility Card[...]

Take Apart DOS Compatibility Card - 16 Note : You must remove the sound card (if present) before returning the DOS Compatibility card to Apple. DOS Compatibility Card[...]

Take Apart DOS Compatibility Card - 17 1 Remove the thumbscrews that secure the DOS Compatibility card to the computer’s rear panel. Rear Panel Thumbscrews[...]

Take Apart DOS Compatibility Card - 18 2 Lift straight up on the DOS Compatibility card to remove it from the expansion slot on the logic board. Adapter Card Tab Adapter Card Connector Bottom Case Slot Expansion Slot[...]

Take Apart DOS Compatibility Card - 19 3 I f a CD-ROM drive is present, unplug the CD audio cables from the Sound Out and CD In connectors on the DOS Compatibility card. Replacement Note: Connect the CD Audio cable that is plugged into the CD-ROM drive into the CD In connector on the DOS Compatibility card. Connect the CD Audio cable that is plugge[...]

Take Apart DOS Compatibility Card - 20 4 If no CD-ROM drive is present, unplug the CD audio c able from the Sound Out connector on the DOS Compatibility card. Replacement Note: The CD audio cable should connect from the CD audio connector on the logic board to the Sound Out connector on the DOS Compatibility card. DOS Compatibility Card Sound Out C[...]

Take Apart DOS Compatibility Card - 21 5 Remove the two screws that secure the sound card to the DOS Compatibility card. 6 Lift straight up on the sound card to remove it. Note: You must remove the sound card before returning the DOS Compatibility card to Apple. Sound Card Screws DOS Compatibility Card[...]

Take Apart DOS Compatibility Card - 22 Important: The jumper at location J10 on the DOS Compatibility card is mismarked. When installing a new DOS Compatibility card, make sure the jumper at J10 is in the “SX” position (over the two right-most prongs) or you may experience problems with the card. See the “Miscellaneous” topic in the Trouble[...]

Take Apart Floppy Drive - 23 Floppy Drive Before you begin, remove the top housing. Caution : Review the ESD precautions in Bulletins/ Safety. Floppy Drive[...]

Take Apart Floppy Drive - 24 1 Slide the drive forward a couple of inches. 2 Lift up and out on the EMI shield to remove it from the front of the floppy drive.[...]

Take Apart Floppy Drive - 25 3 Press the tabs outward and slide the floppy drive forward a few inches. Floppy Drive Tab Tab[...]

Take Apart Floppy Drive - 26 4 Disconnect the floppy drive cable. Note: You can easily reach the floppy drive cable connector when the floppy drive is forward. 5 Slide out the floppy drive. Floppy Drive Cable[...]

Take Apart Hard Drive - 27 Hard Drive Before you begin, remove the top housing. Caution : Review the ESD precautions in Bulletins/ Safety. Hard Drive[...]

Take Apart Hard Drive - 28 1 Disconnec t the SCSI data and hard drive power cables from the hard drive. SCSI Data Cable Hard Drive Power Cable[...]

Take Apart Hard Drive - 29 2 Remove the hard drive EMI shield. Hard Drive EMI Shield[...]

Take Apart Hard Drive - 30 3 Press d own on the tab and slide out the hard drive. Tab[...]

Take Apart CD-ROM Drive - 3 1 CD-ROM Drive Before you begin, remove the top housing. Caution : Review the ESD precautions in Bulletins/ Safety. CD-ROM Drive[...]

Take Apart CD-ROM Drive - 3 2 1 Disconnect the SCSI data cable and C D-ROM drive power cable from the CD-ROM drive. 2 Disconnect the CD-ROM audio cable. SCSI Data Cable CD-ROM Drive Power Cable[...]

Take Apart CD-ROM Drive - 3 3 3 Remove the CD-ROM drive EMI shield. Bottom Cover CD-ROM Drive EMI Shield[...]

Take Apart CD-ROM Drive - 3 4 4 Press up on the tab and slide out the CD-ROM drive. Replacement Note: Be sure to r emove the CD- ROM drive from the carrier prior to returning the drive to Apple. Tab[...]

Take Apart Bottom Housing Assy - 3 5 Bottom Housing Assy Before you begin, remove the following: • Top housing • Power supply • Floppy drive • Hard drive • CD-ROM drive (if installed) • Logic board Caution : Review the ESD precautions in Bulletins/ Safety. Bottom Housing Assy[...]

Take Apart Bottom Housing Assy - 3 6 Note: O nce you have removed all the parts listed on the previous page, the bottom housing assembly is what remains. It includes the floppy drive cable, LED cable, speaker, and internal chassis. Bottom Housing Assy[...]

Take Apart Speaker & Floppy Cable - 3 7 Speaker & Floppy Cable Before you begin, remove the following: • Top housing • Power supply • Floppy drive • Hard drive • CD-ROM drive (if installed) • Logic board Caution : Review the ESD precautions in Bulletins/ Safety. Ê Internal Chassis Floppy Cable Speaker[...]

Take Apart Speaker & Floppy Cable - 3 8 Note: The chassis is secured to the bottom cover by two tabs at the front of the unit, two rail and tab sets at the sides of the unit, support posts at the back of the chassis, and hidden brackets that slide into the bottom cover. 1 Press up on one of the front tabs while lifting the support post. 2 Repea[...]

Take Apart Speaker & Floppy Cable - 3 9 3 Press down and slide the chassis toward the back of the com puter. 4 Remove the chassis. Internal Chassis[...]

Take Apart Speaker & Floppy Cable - 4 0 Note: The LED cable, floppy drive cable and speaker are part of the internal chassis assembly. 5 Turn the chassis over. 6 Remove the floppy drive cable and the LED cable. Speaker and Cable Floppy Drive Cable LED Cable[...]

Take Apart Speaker & Floppy Cable - 4 1 7 Remove the two torx screws from the speaker. 8 Remove the speaker cable from its routing guides. 9 Lift out the speaker. Torx Screws[...]

Take Apart Speaker & Floppy Cable - 4 2 Replacement Note: To replace the chassis, carefully slide rails at the side of the chassis under the metal tabs. Bottom Cover Internal Chassis Metal Tab Rail[...]

Take Apart Speaker & Floppy Cable - 4 3 Replacement Note: After carefully aligning the side r a i ls, push down firmly on the chassis and slide it toward the front of the unit. The tabs will snap in place.[...]

Service Source K Additional Procedures Po wer Macintosh 6100/WS 6150[...]

Additional Procedures Battery Verification - 1 Battery Verification Before you begin, remove the top housing. W arning: If handled or discarded improperly, the lithium battery in the computer could explode. Review battery handling and disposal instructions in Bulletins/Safety. Caution : Review the ESD precautions in Bulletins/ Safety. Battery[...]

Additional Procedures Battery Verification - 2 1 Se t the voltmeter to the 10 volts DC scale. 2 Hold the positive probe of the voltmeter to the positive end of the battery (marked “+” on the logic board) and the negative probe to the negative end of the battery. 3 If the battery voltage is below 3.2 volts, replace the battery. Refer to “Batte[...]

Additional Procedures Battery Replacement - 3 Battery Replacement Before you begin, remove the top housing. W arning: If handled or discarded improperly, the lithium battery in the computer could explode. Review battery handling and disposal instructions in Bulletins/Safety. Caution : Review the ESD precautions in Bulletins/ Safety. Battery[...]

Additional Procedures Battery Replacement - 4 1 Using a small flat-blade screwdriver, pry open the latch at the end of the battery holder and lift off the cover.[...]

Additional Procedures Battery Replacement - 5 2 Grasp the battery and remove it from the holder. 3 Return the battery to Apple for proper disposal. For informa- tion on battery packaging and labeling, refer to the instructions in Bulletins/Safety.[...]

Additional Procedures Reset Logic Board - 6 Reset Logic Board Before you begin, remove the following: • Top housing • Power cord Note: Whenever you have a unit that fails to power up, follow this procedure to reset the logic board before replacing any modules. Battery[...]

Additional Procedures Reset Logic Board - 7 W arning: If handled or discarded improperly, the lithium battery in the computer could explode. Review battery handling and disposal instructions in Bulletins/Safety. Caution : Review the ESD precautions in Bulletins/ Safety. Battery[...]

Additional Procedures Reset Logic Board - 8 1 Unplug the computer first. 2 Using a small flat-blade screwdriver, pry open the latch at the end of the battery holder and lift off the cover.[...]

Additional Procedures Reset Logic Board - 9 3 Grasp the battery and remove i t from the holder.[...]

Additional Procedures Reset Logic Board - 1 0 4 Press the power on button. 5 Disconnect the power supply cable from the logic board. Wait 5–10 minutes and then • Replace the battery • Reconnect the power supply cable • Reassemble the computer Replacement Note: Make sure the battery is facing in the correct direction. Power On Button[...]

Additional Procedures Reset Logic Board - 1 1 Note: T his procedure resets PRAM. Be sure to check the computer’s time/date and other system parameter settings. Note: If this procedure resolves the problem, claim an adjustment on an SRO. If not, replace the defective component and do not claim the adjustment procedure. Power On Button[...]

Service Source K Upgrades Po wer Macintosh 6100/WS 6150[...]

Upgrades Expansion Cards - 1 Expansion Cards Before you begin, remove the following: • Top housing • SCSI hard drive cable Caution : Review the ESD precautions in Bulletins/ Safety. Note: The Power Macintosh 6100/60AV has an AV card in the PDS slot. You cannot install expansion cards in this machine. Expansion Card Slot[...]

Upgrades Expansion Cards - 2 1 Remove the expansion port cover from the rear panel. Expansion Port Cover[...]

Upgrades Expansion Cards - 3 2 Loos ely connect the expansion card connector to the adapter card connector. Note: Be sure to fit the adapter card pin into the expansion card hole. 3 Gently press the connectors together. Expansion Card Adapter Expansion Adapter Card Card Hole Card Pin[...]

Upgrades Expansion Cards - 4 4 Insert the connector on the bottom of the adapter card into the expansion slot. Note: Make sure that the tab on the side of the adapter card slides into the slot on the side of the bottom housing. Adapter Card Tab Adapter Card Connector Bottom Housing Slot Expansion Slot[...]

Upgrades Expansion Cards - 5 5 Attach the thumbscrews. 6 Reconnect the SCSI hard drive cable making sure you run the cable over the expansion card. Thumbscrews[...]

Upgrades CD-ROM Upgrade - 6 CD-ROM Upgrade Before you begin, remove the top housing. Caution : Review the ESD precautions in Bulletins/ Safety. CD-ROM Drive Bay[...]

Upgrades CD-ROM Upgrade - 7 1 Remove the blank CD- ROM drive b ezel from the top housing. 2 Install the slotted CD- ROM drive bezel in the top housing. Slotted CD-ROM Drive Bezel[...]

Upgrades CD-ROM Upgrade - 8 3 Pry off the metal 5.25" drive bay shield. 5.25'' Drive Bay Shield[...]

Upgrades CD-ROM Upgrade - 9 4 Attach the CD-ROM drive carrier to the CD-ROM drive with four Phillips screws. CD-ROM Drive Carrier CD-ROM Drive[...]

Upgrades CD-ROM Upgrade - 10 5 Push in the CD-ROM drive and carrier. CD-ROM Drive CD-ROM Drive Carrier[...]

Upgrades CD-ROM Upgrade - 11 6 Align the slots at the lower edge of th e C D - ROM shield with the tabs on the bottom housing. 7 Swing up the CD-ROM shield until it snaps securely onto the bottom housing. Bottom Cover Tabs Slots CD-ROM Shield[...]

Upgrades CD-ROM Upgrade - 12 8 Connect these cables from the power supply to the CD-ROM drive: • CD-ROM audio cable • SCSI data cable • CD-ROM drive power cable 9 Connect the other end of the CD-ROM audio cable to the logic board. CD-ROM Audio Cable SCSI Data Cable CD-ROM Drive Power Cable CD-ROM Audio Cable[...]

Upgrades DOS Compatibility Upgrade - 1 3 DOS Compatibility Upgrade Before you begin, remove the top housing. Caution : Review the ESD precautions in Bulletins/ Safety. Note: The Power Macintosh 6100/60AV has an AV card in the PDS slot. You cannot install the DOS Compati- bility card in this machine. Expansion Card Slot[...]

Upgrades DOS Compatibility Upgrade - 1 4 Note: The DOS Compati- bility Upgrade Kit comes with a DOS Compatibility card installed in a bracket adapter, a monitor cable with four connectors, a hard drive power extension cable, a monitor cable adapter, a CD-ROM audio cable, and two thumbscrews. Expansion Card Slot[...]

Upgrades DOS Compatibility Upgrade - 1 5 1 Remove the expansion port cover from the rear panel. Expansion Port Cover[...]

Upgrades DOS Compatibility Upgrade - 1 6 2 Un p lug the power cable from the hard drive. Hard Drive Hard Drive Power Cable[...]

Upgrades DOS Compatibility Upgrade - 1 7 3 Connect the power cable that you disconnected from the hard drive to one end of the hard drive power extension cable. 4 Route the extended hard drive power cable around the standoff. 5 Plug the cable into the hard drive. Hard Drive Standoff Hard Drive Power Extension Cable Hard Drive Power Cable[...]

Upgrades DOS Compatibility Upgrade - 1 8 Installation With CD-ROM Drive Present 6 Unplug the CD audio cable from the computer’s logic board. 7 Plug this end of the CD audio cable into the CD In connector on the DOS Compatibility card. Note: The CD Audio cable should now connect the CD-ROM drive to the DOS Compatibility card through the CD In Conn[...]

Upgrades DOS Compatibility Upgrade - 1 9 8 Plug one end of the CD audio cable that came with the upgrade kit into the Sound Out connector on the DOS Compatibility card. 9 Plug the other end of this cable into the CD audio connector on the computer’s logic board. DOS Compatibility Card Sound Out Connector CD Audio Cable CD Audio Connector on Logic[...]

Upgrades DOS Compatibility Upgrade - 2 0 Installation Without CD-ROM Drive 1 0 Plug on e end of the CD audio cable that came with the upgrade kit into the Sound Out connector on the DOS Compatibility card. 1 1 Plug the other end of this cable into the CD audio connector on the computer’s logic board. DOS Compatibility Card Sound Out Connector CD [...]

Upgrades DOS Compatibility Upgrade - 2 1 Important: The jumper at location J10 on the DOS Compatibility card is mismarked. When installing the card, make sure the jumper at J10 is in the “SX” position (over the two right-most prongs) or you may experience problems with the card. See the “Miscellaneous” topic in the Troubleshooting Chapter f[...]

Upgrades DOS Compatibility Upgrade - 2 2 Note: F old the SCSI ribbon cable back so that it doesn’t get caught under the DOS Compatibility card. The cable should fold over the top of the card. Note: Hold the hard drive power cable, which runs underneath the DOS Compatibility card, out of the way when installing the card. 1 2 Insert the connector o[...]

Upgrades DOS Compatibility Upgrade - 2 3 Note: Make sure that the tab on the side of the adapter card slides into the slot on the side of the bottom housing. Adapter Card Tab Adapter Card Connector Bottom Case Slot Expansion Slot[...]

Upgrades DOS Compatibility Upgrade - 2 4 1 3 Attach the thumbscrews that secure the DOS Compatibility card to the computer’s rear panel. Note: Fold the CD Audio cable inside the computer so it doesn’t get caught when you replace the cover. 1 4 Replace the top housing on the computer. Thumbscrews Rear Panel[...]

Upgrades DOS Compatibility Upgrade - 2 5 15 Plug the HDI-45 end of the monitor adapter cable into the monitor port on the back of the computer. 16 Plug the male DB-15 connector on the 4- headed monitor cable into the monitor adapter cable. 17 Plug the female DB-15 connector on the 4- headed monitor cable into the back of the monitor. DOS Compatibil[...]

Upgrades DOS Compatibility Upgrade - 2 6 1 8 Plug the 26-pin male connector on the 4- headed monitor cable into the DOS Compatibility card. DOS Compatibility Card Male 26-Pin Connector Joystick Connector Monitor Adapter Cable Male DB-15 Connector 4-Headed Monitor Cable Female DB-15 Connector[...]

Upgrades Power Macintosh Upgrade - 2 7 Power Macintosh Upgrade Before you begin, remove the following: • Top housing • Power supply • Logic board Caution : Review the ESD precautions in Bulletins/ Safety. Power Macintosh 6100/60 and WS 6150 Logic Board[...]

Upgrades Power Macintosh Upgrade - 2 8 Note: The Power Macintosh 6100/60 and WS 6150 upgrade kits contain a Power Macintosh logic board, insulator sheet I/O panel, rubber foot, SCSI cable, floppy drive EMI shield, CD gasket, and PowerPC or WS 6150 sticker. The Power Macintosh 6100/60AV upgrade also includes the Power Macintosh AV Card. Power Macint[...]

Upgrades Power Macintosh Upgrade - 2 9 1 Press the tabs outward and slide the floppy drive forward a few inches. Floppy Drive Tab Tab[...]

Upgrades Power Macintosh Upgrade - 3 0 2 Place the metal openings that are on the sides of the EMI shield (provided in the upgrade kit) over the screws that are on either side of the floppy drive. Note: The top of the EMI shield should rest on top of the floppy drive. Leave the floppy drive pushed out until you replace the power supply later in thi[...]

Upgrades Power Macintosh Upgrade - 3 1 3 Press up on the tab and slide out the CD-ROM drive. CD-ROM Drive[...]

Upgrades Power Macintosh Upgrade - 3 2 4 Remove the adhesive strip from the rubber EMI gasket. Note: The gasket should be placed in the middle of the opening for the CD- ROM drive. 5 Place the rubber gasket on the underneath side of the frame that houses the CD-ROM. Note: Replace the CD- ROM drive, but don’t push it all the way in until you repla[...]

Upgrades Power Macintosh Upgrade - 3 3 6 Using a flat-blade screwdriver, press down and release the four tabs that secure the rear panel to the chassis. 7 Remove the rear panel.[...]

Upgrades Power Macintosh Upgrade - 3 4 8 Remove the existing insulator sheet and replace it with the insulator sheet provided with the upgrade kit. Insulator Sheet[...]

Upgrades Power Macintosh Upgrade - 3 5 9 Line up the bottom tabs on the rear panel provided in the upgrade kit with the slots in the chassis. 10 Press in on the rear panel until the top tabs snap into place. 11 Affix the blank serial number label that came with the upgrade kit onto the new rear panel. 12 Copy the serial number from the old rear pan[...]

Upgrades Power Macintosh Upgrade - 3 6 Note: Connect the floppy drive cable before inserting the l o gic board. 13 Install the PowerPC logic board. 1 4 If the customer’s original logic board had DRAM SIMMs installed, remove them and install them on the upgraded logic board. Logic Board[...]

Upgrades Power Macintosh Upgrade - 3 7 Important: These upgraded units require that DRAM SIMMs be installed in matching pairs (that is, SIMMs of the same size and speed). The SIMMs must be 80 ns or faster, noncom- posite, 72-pin SIMMs. Replacement Note: Return all nonmatching DRAM SIMMs from the old logic board to the customer. Ê Logic Board[...]

Upgrades Power Macintosh Upgrade - 3 8 Note: The logic board is secured with two screws. 1 5 Replace the standoff and, using a long Phillips screwdriver, tighten the screw in the center of the standoff. 16 Replace the Phillips screw at the front edge of the logic board. Standoff with Internal Screw[...]

Upgrades Power Macintosh Upgrade - 3 9 1 7 Replace the SCSI data cable with the one provided in the upgrade kit. 1 8 Connect these cables to the logic board • Floppy drive cable • Speaker cable • LED cable • CD-ROM audio cable (if present) • SCSI data cable Floppy Drive Cable Speaker Cable LED Cable CD-ROM Audio Cable SCSI Data Cable[...]

Upgrades Power Macintosh Upgrade - 4 0 1 9 Reconnect these power supply cables • Main power cable • Hard drive power cable • CD-ROM drive power cable (if installed) Main Power Cable CD-ROM Drive Power Cable Hard Drive Power Cable[...]

Upgrades Power Macintosh Upgrade - 4 1 2 0 Re place the power supply. 2 1 Tighten the screw that secures the power supply to the chassis. 22 Push in the CD-ROM drive until you hear it click into place. Power Supply[...]

Upgrades Power Macintosh Upgrade - 4 2 2 3 Lift up on the top of the metal EMI shield and slide the floppy drive back into place. Note: The top of the metal EMI shield should rest of top of the chassis frame. 2 4 For the Power Macintosh 6100/60AV only, install the Power Macintosh AV Car d i n the expansion slot on the logic board. Refer to “Expan[...]

Upgrades Power Macintosh Upgrade - 4 3 25 Replace the top housing and turn the unit over. 2 6 Remove the adhesive strip from the rubber foot provided in the upgrade kit. 2 7 Press the rubber foot onto the bottom chassis towards the back of the unit and directly in front of the screw that secures the logic board to the chassis. Screw Foot[...]

Upgrades Power Macintosh Upgrade - 4 4 2 8 Adhere the 6100/60 or WS 6150 sticker to the front of the unit, directly over the current model name. Note: For the Power Macintosh 6100/60 upgrade, you must install the System 7.1.2 software that came with the upgrade kit. Refer to the user manual provided in the upgrade kit for installation instructions.[...]

Upgrades Power Macintosh Upgrade - 4 5 29 Run MacTest Pro in looping mode or other software in demo mode for 1 hour as a burn-in test. Note: Contact Finished Goods for an RMA number to return the old logic board.[...]

Service Source K Exploded V ie w Po wer Macintosh 6100/WS 6150[...]

Exploded View 1 Top Housing (PM) 922-0807 (WS) 922-0993 Blank Bezel 922-0358 Slotted CD Bezel w/ Caddy 922-0805 Slotted CD Bezel Caddiless Power Supply 661-1688 Floppy Drive Cable 922-0351 SCSI Cable 922-1207 Support Column 922-0356 Logic Board 661-0207 661-1022 Insulator Sheet 922-0808 Rear Housing Assy 922-0720 Expansion Plug 922-0902 Feet (4) 92[...]