Amplifier Tech AT1202 инструкция обслуживания

A T602 AND A T1 202 2-CHANNEL POWER AMPLIFIER OWNER’S GUIDE TRANSL A TING TECHNOL OG Y[...]

Safe ty Ins tructions W ARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. Read all the safety and operating instructions befor e connecting or using this unit. All warnings on the unit and in this operating manual should be adhered to. All operating and use instructions should be follo wed. Do not us[...]

T able of Contents Please Read First ............................................................ Pag e 2 Safe ty Instr uctions ........................................................ Page 2 T able of Contents .......................................................... Pag e 3 Introduction ...........................................................[...]

Pa ge 4 F A C Fuse Y our amplifier is supplied with a rear panel mounted main A C fuse. This main fuse may need replacement if the unit will not turn on. Nev er replace the the main fuse with other than the one indicated. W ARNING: Always turn off the amplif ier and unplug t he power cord befor e making any electrical connections. G AC Input Use th[...]

Connecting Y our Amplif ier When making connections between any source components and the amplifier , or when making connections to any speaker , be cer tain that both the input devices and the amplifier are turned off. T o assure that there will be no unwanted signal transients that can damage equipment or speakers, it is always best to unplug all[...]

Pa ge 6 Making Rear P anel Connections When connecting the amplif ier to y our source equipment, match the output channel designations on the rear of your source equipment to the input jacks on the rear panel of y our amplifier that have the same channel name. Correct polar ity connections are important to maintain proper speaker phasing. When maki[...]

Pa ge 7 Left Speaker essor Shown as a Typical Exam ple e, The Amplier Is or a 2nd Zone[...]

Power Contr ol Connections Y our amplifier featur es a built-in remo te tur n-on system that will automatically switch the amplifier on when another device in the system is switched on. Remote Turn-On Using Products Equipped With a Low V oltag e Trigger Jack Press the front panel pow er switch on the amplifier so that it is in the ON position. Then[...]

Problem Solutions Amplif ier will not turn on Master Po wer Switch tuned of f (No pow er light LED). Turn on Master Po wer Switch. Amplif ier will not turn of f. Remo te tr igger cable not proper ly connected. V erify connection of trigger cable at both ends. Amplif ier tur ns on, but no audio from one or more channels. Input plugs not connected to[...]

Pa ge 10 Suggestion #3: Ground loop problems may also be caused by poor g rounding of the electr ical system in your home, par ticularly when there are multiple components with three prong, grounded, pow er cords. Try unplugging these components one at a time, and see if one or all of them is causing the problem. The ultimate solution to this type [...]

Pa ge 11 Series AT602 A T1202 Number of Channels 22 EIA 1kHz Output Power at 8 Ohms* 75 watts 1 40 watts EIA 1kHz Output Power at 4 Ohms* 1 1 0 watts 220 watts FTC Full Bandwidth Output P ower at 8 Ohms** 60 watts 1 20 watts FTC Full Bandwidth Output P ower at 4 Ohms** 90 watts 1 80 watts Input Sensitivity for Full Rated Power 0.9 V olts 1 .3 V olt[...]

90-Day Limited Warranty T erms and Conditions (7-Y ear Optional Extended W ar ranty) This ATI product is warranted against defects in materials and w orkmanship for 90 days from the date of purchase by t he original owner . The date of purchase shall be established by the or iginal owner presenting to the ATI Customer Ser vice F acility the origina[...]