Alpha Vision Tech MPS48-7M инструкция обслуживания

Alpha T echnologies T echnical Manual MPS48-7M Effective: August 2007[...]

Power Alpha T echnologies ®[...]

MPS48-7M T echnical Manual 021-51 1-B4-002, Rev . B Ef fective Date: August 2007 Copyright© 2007 Alpha T echnologies, Inc. member of The Group TM Notice of FCC Compliance Per FCC 47 CFR 15.21: Changes or modi fi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Per F[...]

4 021-51 1-B4-002, Rev . B Contents Safety Notes .................................................................................................................. ........ 6 1.0 Introduction .............................................................................................................. .1 0 2.0 Theory of Operation ..................[...]

5 021-51 1-B4-002, Rev . B List of Figures and T ables Fig. 1-1, MPS48-7M Overview ............................................................................................ 10 Fig. 3-1, MPS48-7M Enclosure Dimensions........................................................................ 13 Fig. 4-1, AC Connections................................[...]

6 021-51 1-B4-002, Rev . B Safety Notes Review the drawings and illustrations in this manual before proceeding. If there are any questions regarding the safe installation or operation of this product, contact Alpha T echnologies or the nearest Alpha representative. Save this document for future reference. T o reduce the risk of injury or death, and[...]

7 021-51 1-B4-002, Rev . B General Safety Precautions T o avoid injury: • This enclosure and its hardware must only be serviced by authorized personnel. • The enclosure must remain locked at all times, except when authorized service personnel are present. • Remove all conductive jewelry or personal equipment prior to servicing equipment, part[...]

8 021-51 1-B4-002, Rev . B Lead-acid batteries contain dangerous voltages, currents, and corrosive material. Battery installation, maintenance, service, and replacement must be performed only by authorized personnel. Battery Safety Notes W ARNING! Chemical Hazards Any gelled or liquid emissions from a valve-regulated lead-acid (VRLA) battery contai[...]

9 021-51 1-B4-002, Rev . B Battery Maintenance Guidelines The battery maintenance instructions listed below are for reference only . Battery manufacturer ’ s instructions for transportation, installation, storage or maintenance take precedence over these instructions. • Inspect batteries every 6 months for: Signs of battery cracking, leaking or[...]

10 021-51 1-B4-002, Rev . B 1.0 Introduction Alpha’s FlexNet MPS48-7M multipurpose power supply provides primary and standby power to Wi-Fi radios in wall-mount and pole-mount applications. The MPS48-7M interface module includes connections for radio, Ethernet backhaul, local Craft port, and 48Vdc auxiliary connection. The MPS48-7M is supported b[...]

11 021-51 1-B4-002, Rev . B 2.0 Theory of Operation The FlexNet MPS48-7M multipurpose power supply provides fi ltered 50W output power for a typical 48V telecom bus during normal line operation. During line disruptions, the MPS48-7M supplies uninterrupted output power of 50W directly from a string of four 12V batteries. Metal oxide varistor (MOV) [...]

12 021-51 1-B4-002, Rev . B Input V oltage Range (switch selectable) 90-132V ac (low range) or 180-264V ac (high range), 250 to 347V ac with optional step-down transformer Frequency 47Hz or 63Hz Surge Protection ANSI/IEEE Std. C62.41 to Category A, B, or C requirements, using a “Ring W ave” or “Combination” waveform, at a level of 6kV Outpu[...]

13 021-51 1-B4-002, Rev . B Fig. 3-1, MPS48-7M Enclosure Dimensions Spare Parts and Options Part Number Product Name 189-078-20 Battery Heater for the MPS48-7M, 240V ac 189-078-21 Battery Heater for the MPS48-7M, 120V ac 745-866-20 Mounting Bracket with Hardware (included) 745-863-20 AC Line Cord, 5-15P , 8' 745-850-22 T ransformer Kit, 277V a[...]

14 021-51 1-B4-002, Rev . B 4.0 Installation 4.1 Unpacking the MPS48-7M Remove the mounting bracket and enclosure from the shipping carton. Inspect the MPS48-7M for shipping damage. V erify each carton contains: • MPS48-7M enclosure • Mounting bracket and hardware • 3/4" 3-hole strain relief fi tting • 1/2" strain relief fi ttin[...]

15 021-51 1-B4-002, Rev . B 4.0 Installation, continued 4.2 Enclosure Installation, Wall-mount or W ooden Pole Mount, continued 4. Hang the enclosure on the bracket. 5. Secure the enclosure to the bracket using the four self-tapping screws with washers (supplied). Proceed to Section 4.4.[...]

16 021-51 1-B4-002, Rev . B 4.0 Installation, continued 4.3 Enclosure Installation, Steel or Concrete Pole T o mount the MPS48-7M on concrete or steel poles, two user-supplied mounting straps are required (straps must be stainless, galvanized, or equivalent). Most codes require the base of the enclosure to be located a minimum height from the groun[...]

17 021-51 1-B4-002, Rev . B 1. V erify utility power is OFF . T ag and lock utility power switch. 2. Remove the 1/2" EMT knockout (7/8" dia.) and the 3/4" EMT knockout (1 1/8" dia.), located in the center bottom of the enclosure. For alternate installation, remove knockouts from the right side, left side, or back left of the enc[...]

18 021-51 1-B4-002, Rev . B 4.0 Installation, continued 4.5 AC Connection with High V oltage T ransformer The transformer converts high voltage to 240V ac. The transformer is required for powering the MPS48-7M from high voltage light pole applications. Use the following connection procedures for installing the transformer kit. Required T ools and M[...]

19 021-51 1-B4-002, Rev . B 4.0 Installation, continued 4.5 AC Connection with High V oltage T ransformer , continued 4.5.2 Installing the Streetlight AC Power T ap Cable 1. Remove the 1/2" EMT knockout (7/8" dia.) and the 3/4" EMT knockout (1 1/8" dia.), located in the center bottom of the enclosure. For alternate installation,[...]

20 021-51 1-B4-002, Rev . B 4.0 Installation, continued 4.6 Network Cable Connection Procedure Required T ools and Materials: Channellock pliers 1. Remove the white seal from the 3-hole strain relief fi tting, and install the base of the fi tting into the 3/4" knockout. Secure the top inside nut. 2. Route the customer-supplied connection cab[...]

21 021-51 1-B4-002, Rev . B 4.0 Installation, continued 4.7 Battery Connection Procedure Required T ools and Materials: • #2 fl athead screwdriver • Electrical tape 1. Loosen the retaining screw on the battery retaining bracket and move the bracket clear of the battery shelf. 2. If using the battery heater mat option, verify the input voltage [...]

22 021-51 1-B4-002, Rev . B 5.0 Operation 5.1 Start-up 1. V erify the input voltage select switch on the power module is set for the correct input voltage. The factory default setting is 240V ac. 2. V erify customer-end connections and apply AC power to the unit. 3. Connect the battery terminal left unplugged in Section 4.7. 5.2 Normal Operation Th[...]

23 021-51 1-B4-002, Rev . B 5.0 Operation 5.3 Battery Backup Mode In the event of an AC power outage, the MPS48-7M switches to battery backup mode to power the load. The green status LED begins to blink, indicating the load is being powered from the battery string. The MPS48-7M runs in battery backup mode until AC power is restored, or until the ba[...]

24 021-51 1-B4-002, Rev . B 6.0 T roubleshooting 6.1 T roubleshooting T able T roubleshooting T able Fault Corrective Action Green LED is blinking after initial startup V erify AC power is ON. Check voltage at AC input block. Check AC input connector on power module. Red LED is ON solid Replace batteries. Red LED is blinking If no batteries are mis[...]

25 021-51 1-B4-002, Rev . B 7.0 Maintenance 7.1 Battery Replacement The MPS48-7M batteries are hot-swappable. There is no need to power down the unit when replacing the batteries. Required T ools and Materials: #2 fl athead screwdriver 1. Unplug the battery connections. 2. Loosen the retaining screw on the battery retaining bracket and move the br[...]

26 021-51 1-B4-002, Rev . B 7.0 Maintenance, continued 7.3 Battery Management Batteries have limited shelf life and must be put into service in a timely manner . The chart below provides general storage guidelines and illustrates the relationship between capacity retention and storage temperature over time. Consult battery documentation for product[...]

Due to continuing product improvements, Alpha reserves the right to change speci fi cations without notice. Copyright © 2007 Alpha T echnologies, Inc. All rights reserved. Alpha is a registered trademark of Alpha T echnologies. 021-51 1-B4-002, Rev . B. Power Alpha T echnologies ® Alpha T echnologies 3767 Alpha W ay Bellingham, WA 98226 USA T el[...]