Zenoah BC2310DL manual

GB-1 G B BC2310DL BC2310DL G B OWNER’S MANUAL BRUSHCUTTERS 848J9893A1 (708)[...]

GB-2 BC2310DL EXPLANA TION OF SYMBOLS AND SAFETY W ARNINGS 22.5 cm 3 SOUND LEVEL VIBRA TION LEVEL ISO 22868 : 2005 LwA measured 107.9 dB(A) guaranteed 110 dB(A) ISO 22867 : 2004 idling 3.5 m/s 2 racing 5.3 m/s 2 MODEL LpA EN27917 97.3 dB(A) BC2310DL APPROV AL NUMBER OF CE EXHAUST EMISSION REGULA TION DIRECTIVE 97/68/EC AMENDED 2002/88/EC e13*97/68S[...]

GB-3 G B BC2310DL SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury , and for this reason you are requested to read all such instructions carefully and follow them without fail. W ARNINGS IN THE MANUAL W ARN[...]

GB-4 BC2310DL 5 14 3 1 2 4 12 11 13 9 10 8 7 6 1. Par ts location (1) Primer pump (2) Air cleaner cover (3) Choke lever (4) Fuel tank (5) Starter knob (6) Line head (7) Gear case (8) Cutting attachment guard (9) Loop handle (10) Shaft tube (11) Suspention point (12) Throttle trigger (13) Stop switch (14) Throttle cable 2. Specification Overall size[...]

GB-5 G B BC2310DL 3. W ar ning labels on the machine 4. Symbols on the machine For safe operation and maintenance, symbols are carved in r elief on the machine. According to these indications, please be careful not to make a mistake. The port to refuel the “MIX GASOLINE” Position: FUEL T ANK CAP The direction to close the choke Position: AIR CL[...]

GB-6 BC2310DL b. At night, at times of heavy fog, or at any other times when your field of vision might be limited and it would be diffi- cult to gain a clear view of the working area. c . During rain storms, during lightning storms, at times of strong or gale-for ce winds, or at any other times when weather conditions might make it unsafe to use t[...]

GB-7 G B BC2310DL BEFORE ST ARTING THE ENGINE 1 . The area within a perimeter of 15 m of the person using the product should be consider ed a hazardous ar ea into which no one should enter . If necessary , yellow warning rope, warning signs should be placed around the pe- rimeter of the area. When work is to be perfor med simultaneously by two or m[...]

GB-8 BC2310DL 5. For safe operation HANDLING FUEL 1. The engine of the ZENOAH prod- uct is designed to run on a mixed fuel, which contains highly flam- mable gasoline. Never store cans of fuel or refill the tank of the unit in any place where ther e is a boiler , stove, wood fir e, electrical sparks, welding sparks, or any other source of heat or f[...]

GB-9 G B BC2310DL 6. Set up INST ALLING HANDLE • Mount the handle to the shaft tube and clamp it at a location that is comfortable to you. (1) INST ALLING CUTTING A TT ACHMENT GUARD • Attach the cutting attachiment guar d with the bolts provided while inserting the spacer between the guard and the pipe. • Attach the guard skirt on the guard. [...]

GB-10 BC2310DL ■ RECOMMENDED MIXING RA TIO GASOLINE 50 : OIL 1 <when using ZENOAH genuine oil> • Exhaust emission are controlled by the funda- mental engine parameters and components (eq., carburation, ignition timing and port timing) with- out addition of any major hardware or the intro- duction of an inert material during combustion. ?[...]

GB-11 G B BC2310DL 8. Operation ST A R T Stop Start 3. Ignition switch 1 2 S T A R T Stop Start Ignition switch WARNING The product is equipped with a centrifugal clutch mechanism, so the cutting attachment begins to ro- tate as soon as the engine is started by putting the throttle into the start position. When starting the en- gine, place the prod[...]

GB-12 BC2310DL 8. Operation .04 in (1 ~ 2 mm) TRIMMING GRASS AND WEEDS • Always r emember that the TIP of the line does cut- ting. Y ou will achieve better r esults by not crowding the line into the cutting area. Allow the unit to trim at its own pace. 1. Hold the unit so the head is off the gr ound and is tilted about 20 degrees towar d the swee[...]

GB-13 G B BC2310DL Every Every Every 25 50 100 System/components Procedure Before hours hours hours Note use after after after fuel leaks, fuel spillage wipe out ✔ fuel tank, air filter , fuel filter inspect/clean ✔✔ replace, if necessary see adjusting replace carbur etor idle adjusting screw idling speed ✔ if necessary clean and readjust G[...]

GB-14 BC2310DL GEAR CASE • The reduction gears ar e lubricated by multipurpose, lithium-based gr ease in the gear case. Supply new grease every 25 hours of use or mor e often depend- ing on the job condition. • Remove the bolt opposit to the grease nipple befor e installing new grease to arrange for old gr ease to exit. INT AKE AIR COOLING VENT[...]

GB-15 G B BC2310DL PROCEDURES TO BE PERFORMED AFTER EVER Y 100 HOURS OF USE 1. Remove the muffler , insert a screwdriver into the vent, and wipe away any carbon buildup. Wipe away any carbon buildup on the muffler exhaust vent and cylin- der exhaust port at the same time. 2. Tighten all screws, bolts, and fittings. 3. Check to see if any oil or gre[...]

GB-16 BC2310DL Limited warranty Should any failure occur on the pr oduct under nor mal oper - ating conditions within the applicable warranty period, the failed part will be replaced or repair ed free of charge by a ZENOAH authorized dealer . W ARRANTY PERIOD: 1 year (6 months if used profession- ally , and 30 days if used for rental purpose) fr om[...]