Zanussi ZGF 982 manual

2 GAS HOB MODEL ZGF 982 INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance[...]

3 Important Safety Infor mation You MUST read hese warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 727727 Installation ● This hob must be installed by qualified personnel, according to the manufacturer ’ s instructions and to the relevant British Standards. ● Any gas[...]

4 This appliance complies with the following E.E.C. Dir ectives: * 73/23 - 90/683 (Low V oltageDirective); * 93/68 (General Directives); * 89/336 (Electromagnetical Compatibility Directive) ; * 90/396 (Gas Appliances) , and subsequent modifications Guide to Use the instructions The following symbols will be found in the text to guide you throughout[...]

5 1. Hob Top 2. Auxiliary Burner 3. Semi-rapid Burners 4. Ultra-rapid Double-crown Burner 5. Rapid Burner 6. Ignition pushbutton 7. Control knob for front left burner (auxiliary) 8. Control knob for back left burner (semi-rapid) 9. Control knob for central burner (ultra-rapid) 10. Control knob for back right burner (semi-rapid) 11. Control knob for[...]

6 Operation HOB BURNERS To light a burner, push the relevant control knob in, turn it anticlockwise to maximum position, and depress the ignition pushbutton marked by a small electric spark symbol. Then adjust the flame as required. If the burner does not ignite, turn the control knob to zero, and try again. T o ensure maximum burner ef ficiency , [...]

7 FO 2347 Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply . The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob T op Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little [...]

8 Something Not W orking? If the hob is not working correctly , please carry out the following checks before contacting your local Zanussi Service Force Centre. IMPOR T ANT : If you call out an engineer to a fault listed below , or to repair a fault caused by incorrect use or installation, a char ge will be made even if the appliance is under guara[...]

9 ZANUSSI GUARANTEE CONDITIONS W e, Zanussi, undertake that if, within 24 months of the date of the purchase, this Zanussi appliance or any part thereof is proved to be defective by any reason only of faulty workmanship or materials, we will, at our option, repair or replace the same FREE OF ANY CHARGE for labour , materials or carriage on conditio[...]

10 OVERALL DIMENSIONS W idth: 860 mm. Depth: 510 mm. Height: 72 mm. W eight: 12 Kg. CUT OUT DIMENSIONS W idth: 830 mm. Depth: 480 mm. Thickness: 30 mm. Ignition HT Spark Spark Generator Ispra Control's BF 50066 - 240V 0.6 Y A T 120 Spark Gap Fixed Rear Left Burner (semi rapid) Heat Input 2.0 kW (6824 BTU/HR) Front Left Burner (auxiliary) Heat [...]

11 Important safety requir ements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE W iring Regulations (Current Edition). Detailed recommendations are contained in the following British Standards Codes Of Practice: B.S. 6172/ B.S. 5440, Part 2 and B.S. 6891 Current Edition[...]

12 Rectangular cut-out size for hob A) End of shaft with nut B) W asher C) Elbow It is important to install the elbow correctly , with the shoulder on the end of the thread, fitted to the hob connecting pipe. Failure to ensure the correct assembly will cause leakage of gas. FO 0814 Gas Connection Connection to the gas supply should be with either r[...]

13 ON/OFF SWITCH FLEX OUTLET ON/OFF SWITCH FLEX OUTLET FO 0763 FO 0764 30 20 min 60 a b FO 1013 1 2 3 FO 0199 a Fitting the Hob into the w orktop Carry out the building in of the hob as follows: • put the seals supplied with the hob, on the edges of the cut out, taking care that the seals meet without overlapping; • place the hob in the cut out[...]

14 Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 230-240[...]

15 A. IGNITOR SWITCH B. IGNITOR UNIT B L N 0 1 2 3 4 5 6 220/240 A W iring Diagram[...]

16 Fault Finding Pr eliminar y Electrical Systems Check A. EARTH CONTINUITY CHECK - Appliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale and adjust zero if necessary . a) T est leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 Ω (Ohm), check all earth wires for continuity and [...]

17 Ignition System / Gas Ignition YES Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Ignitor does not spark Check fitting of burners Check position of the electrode Check by pass simmer adjusted Light burner manually Check gas supply at burner Check continuity fro[...]

18 Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. T o do this, follow the procedure below . - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished[...]