Weider C670 manual

Visit our website at www .weiderfitness.com new products, prizes, fitness tips, and much more! CAUTION Read all precautions and instruc- tions in this manual before using this equipment. Save this manual for future reference. Model No. WEBE37332 Serial No. Write the serial number in the space above for future reference. QUESTIONS? As a manufacturer[...]

2 W ARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . .[...]

3 W ARNING DECAL PLACEMENT Keep hands and fingers clear of this area. • Misuse of this product may result in serious injury . W ARNING ! • Read user ’s manual and follow all warnings and operating instruc- tions prior to use. • Replace label if damaged, illegible, or removed. • Do not allow children on or around machine. The decals shown [...]

1. Read all instructions in this manual before using the weight bench. Use the weight bench only as described in this manual. 2. It is the responsibility of the owner to ensure that all users of the weight bench are ade- quately informed of all precautions. 3. The weight bench is intended for home use only . Do not use the weight bench in any comme[...]

ASSEMBLED DIMENSIONS: Height: 83 in. Width: 66 in. Depth: 90 in. 5 Weight Carriage Wheel Safety Spotter Ab Sling Weight Rest Curl Pad Right Side Left Side Note: The terms “right side” and “left side” are determined relative to a person sitting on the bench; they do not correspond to right and left on the drawings in this manual. Backrest Di[...]

6 Before beginning assembly , carefully read the following information and instructions: • Assembly requires two people. • Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed. • T ighten all parts as you assemble them, unless instructed to do otherwise. • As[...]

7 2. Attach a Small Base Cap (20) to the Bench Base (3) with two M4 x 16mm Screws (36). Attach the other Small Base Cap in the same manner . Press the 51mm x 76mm Inner Cap (14) into the indicated end of the Bench Leg (4). Attach the Bench Leg (4) to the Bench Base (3) with four M10 x 71mm Bolts (31), two Bench Base Joint Plates (25), and four M10 [...]

8 6. Pull out the Small Adjustment Knob (23) that is nearer the Stabilizer (2). Insert the Backrest Bracket (16) between the tubes on the Bench Frame (1) and engage the Small Adjustment Knob into one of the holes in the Bracket. Pull out the Small Adjustment Knob (23) by the Seat Bracket Sleeve (93). Insert the Seat Bracket (17) into the Seat Brack[...]

9 10. Press two 25mm Square Inner Caps (28) into a Pad T ube (27). Slide the Pad T ube into a hole in the Leg Lever (5). Slide two Foam Pads (26) onto the Pad T ube. Assemble the other Pad T ube (27) in the same manner . 12. Attach a Large Base Cap (70) to the Left Base (40) with two M4 x 16mm Screws (36). Attach another Large Base Cap to the other[...]

10 13. Attach a Rear Upright (43) to the Left Base (40) with two M10 x 78mm Bolts (32) and two M10 Nylon Locknuts (34). Note: The Rear Uprights are shorter than the Front Uprights (not shown). Make sure the holes are on the side shown. Do not tighten the Locknuts yet. Repeat this step with the other Rear Upright (43) and the Right Base (38). 14. Pr[...]

11 15. Loosen the two Adjustment Knobs (22) on the Left Safety Spotter (51) by turning them counter- clockwise. Pull both Knobs out at the same time and slide the Left Safety Spotter (51) onto the Left Uprights (43, 44) and engage and tighten the Adjustment Knobs (22) into a set of holes in the Uprights. Repeat this step with the Right Safety Spott[...]

12 18. Attach the Chin-up Bar (54), with the bends going up, to the Left Front Upright (44) and the Left T op Frame (48) with four M10 x 78mm Bolts (32), a Rack Joint Plate (85), and four M10 Nylon Locknuts (34). Do not tighten the Locknuts yet. Attach the Chin-up Bar (54) to the Right Front Upright (not shown) and the Right T op Frame (not shown) [...]

13 20. Press a 60mm Square Inner Cap (64) into the Weight Guide Base (41). Attach the Foot Plate (67) and the Weight Guide Base (41) to the Center Base (39) with two M10 x 81mm Button Bolts (104) and two M10 Nylon Locknuts (34). Do not tighten the Locknuts yet . 22. Slide the W eight Carriage Stop (65) onto the Weight Guide Upright (42) as shown, a[...]

14 23. Press two 48mm W eight Carriage Caps (63) into the Weight Carriage (62). Insert an M10 x 19mm Bolt (102) into the bracket on the Weight Carriage (62) from the side shown. Slide the Weight Carriage (62) onto the W eight Guide Upright (42) so that the weight tube is toward the Center Upright (45). 25. Attach the Butterfly Bracket (55) to the C[...]

15 26. Press a 50mm Square Inner Cap (13) and a 25mm Square Inner Cap (28) into the Right Butterfly Arm (56). Press two Plastic Butterfly Bushings (79) and two Metal Butterfly Bushings (1 13) into the Arm. Wet the bottom of the Butterfly Arm with soapy water and slide a Butterfly Foam Pad (66) onto the Arm. Lubricate a 1/2” x 78mm Bolt (97) and t[...]

16 29. Locate the Medium Cable (69). Route the Cable up through the Weight Guide T op Frame (49) and over a Pulley (87). Attach the Pulley inside the T op Frame with an M10 x 75mm Bolt (92), two M10 W ashers (35), two 17mm Spacers (89), and an M10 Nylon Locknut (34). 31. W rap the Medium Cable (69) under a Pulley (87). Attach the Pulley and a Cable[...]

17 34. Locate the Butterfly Cable (109). Attach the Cable to the Left Butterfly Arm (57) with an M8 x 43mm Shoulder Bolt (107), an M10 Small W asher (95), and an M8 Nylon Locknut (108). 36. W rap the Butterfly Cable (109) under a Pulley (87). Attach the Pulley to the Double “U”-bracket (81) with an M10 x 45mm Bolt (33) and an M10 Nylon Locknut [...]

18 39. Locate the Long Cable (68). Route the eyelet end of the Cable through the Foot Plate (67) and the Center Upright (45), and under a Pulley (87). Attach the Pulley (87) inside the Center Upright (45) with an M10 x 75mm Bolt (92), two M10 W ashers (35), two 17mm Spacers (89), and an M10 Nylon Locknut (34). Note: The Foot Plate (67) is shown pul[...]

This section explains how to adjust the weight bench. See the EXERCISE GUIDELINES on page 24 for impor- tant information about how to get the most benefit from your exercise program. Also, refer to the accompanying exercise guide to see the correct form for each exercise. Make sure all parts are properly tightened each time the weight bench is used[...]

20 5 58 54 76 75 ADDING WEIGHT T O THE LEG LEVER T o add weight (not included) to the Leg Lever (5), slide the desired amount of weight onto the weight tube. Weight T ube Weight USING THE AB SLINGS T o use the Ab Slings (76), use the Large Cable Clips (75) to attach them to the Chin-up Bar (54). 74 74 69 73 62 71 W ARNING: Do not place more than 15[...]

21 101 101 60 34 51 Decal A TT ACHING THE DIP ARM T o attach the Dip Arm (60), first move a Safety Spotter (50 or 51) to the highest position possible (see USING THE WEIGHT RESTS AND SAFETY SPOTTERS below). Attach the Dip Arm to the outside of the Safety Spotter with two M10 x 97mm Carriage Bolts (101) and two M10 Nylon Locknuts (34). Make sure the[...]

22 4 21 MOVING THE BENCH T o move the weight bench, lift the Bench Leg (4) so that the bench pivots onto the Wheels (21). Roll the bench to the desired location and set the Bench Leg down. 9 8 22 A TT ACHING THE CURL P AD OR LEG LEVER T o use the Curl Pad (9), remove the Adjustment Knob (22) and the Leg Lever Bracket (18) from the Seat Frame (7). S[...]

CABLE DIAGRAMS The cable diagrams below show the proper routing of the Long Cable (68), the Medium Cable (69), and the Butterfly Cable (109). Use the diagram to make sure that the cables and the cable traps have been assembled correctly . If the cables have not been correctly routed, the weight rack will not function properly and damage may occur .[...]

24 EXERCISE GUIDELINES THE FOUR BASIC TYPES OF WORKOUTS Muscle Building T o increase the size and strength of your muscles, push them close to their maximum capacity . Y our mus- cles will continually adapt and grow as you progres- sively increase the intensity of your exercise. Y ou can adjust the intensity level of an individual exercise in two w[...]

25 Rest for a short period of time after each set. The ideal resting periods are: • Rest for three minutes after each set for a muscle building workout. • Rest for one minute after each set for a toning work- out. • Rest for 30 seconds after each set for a weight loss workout. Plan to spend the first couple of weeks familiarizing yourself wit[...]

26 MONDA Y Date: / / EXERCISE WEIGHT SETS REPS EXERCISE WEIGHT SETS REPS EXERCISE WEIGHT SETS REPS AEROBIC EXERCISE AEROBIC EXERCISE TUESDA Y Date: / / WEDNESDA Y Date: / / THURSDA Y Date: / / FRIDA Y Date: / / Make photocopies of this page for scheduling and recording your workouts.[...]

27 MONDA Y Date: / / EXERCISE WEIGHT SETS REPS EXERCISE WEIGHT SETS REPS EXERCISE WEIGHT SETS REPS AEROBIC EXERCISE AEROBIC EXERCISE TUESDA Y Date: / / WEDNESDA Y Date: / / THURSDA Y Date: / / FRIDA Y Date: / / Make photocopies of this page for scheduling and recording your workouts.[...]

25mm Square Inner Cap (28) 45mm Square Inner Cap (12) 50mm Square Inner Cap (13) 38mm x 50mm Inner Cap (15 ) 51mm x 76mm Inner Cap (14) 60mm Square Inner Cap (64) 48mm Weight Carriage Cap (63) 48mm Round Inner Cap (19)[...]

M10 x 45mm Bolt (33) M10 x 65mm Bolt (100) M10 x 75mm Bolt (92) M6 W asher (78) M10 W asher (35) M10 Nylon Locknut (34) M8 Nylon Locknut (108) M6 x 16mm Screw (29) 17mm Spacer (89) M4 x 16mm Screw (36) 28mm Spacer (91) M10 x 71mm Bolt (31) M10 x 56mm Bolt (30) M10 x 60mm Bolt (105) M10 x 19mm Bolt (102) M10 Small W asher (95) 1/2" Nylon Locknu[...]

M10 x 78mm Bolt (32) M10 x 97mm Carraige Bolt (101) M10 x 102mm Bolt (99) M10 x 94mm Bolt (98) M10 x 75mm Carriage Bolt (90) M10 x 87mm Bolt (106) M10 x 85mm Bolt (103) M10 x 81mm Button Bolt (104) M6 x 75mm Screw (96) 1/2" x 78mm Bolt (97)[...]

Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of the user ’s manual for information about ordering replacement parts. Key No. Qty . Description Key No. Qty . Description 1 1 Bench Frame 2 1 Stabilizer 3 1 Bench Base 4 1 Bench Leg 5 1 Leg Lever 6 1 Backrest Frame 7 1 Seat Fr[...]

EXPLODED DRA WING—Model No. WEBE37332 R0903A 1 2 20 33 21 34 21 33 100 34 20 98 34 24 4 34 25 25 31 20 20 3 13 19 13 37 37 13 34 103 18 26 27 26 28 28 28 28 12 8 29 9 10 30 7 22 29 29 34 34 17 23 23 15 24 14 29 34 29 16 15 30 35 35 6 11 5 36 36 36 36 35 35 34 99 35 35 35 35 36 93 34 102[...]

54 22 84 52 84 64 85 34 34 32 11 0 44 85 85 34 32 32 85 85 34 36 70 34 84 50 77 22 22 84 36 36 84 84 32 34 32 66 85 34 32 64 84 53 22 84 75 76 76 75 32 34 43 32 32 77 36 36 84 84 22 51 22 84 84 36 70 38 104 67 34 13 56 79 79 32 32 34 47 28 80 97 80 64 32 34 59 58 74 59 34 32 32 32 35 34 34 34 34 86 32 105 111 96 34 32 86 111 105 34 34 46 79 80 80 9[...]

Part No. 205162 R0903A Printed in China © 2003 ICON Health & Fitness, Inc. LIMITED W ARRANTY ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and mate- rial, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This warranty extends only to the [...]