U-Line SP18 manual

Use and Car e Guide BI98 BI95 SP18 Ice Maker Models: BI95, BI98, SP18 ULI N _0 163 57 _3009 8.f m Pag e 1 Tuesda y, M ar ch 14, 20 06 2:32 PM[...]

2 BI95, BI98, SP18 Congratulation s on your purchase of a U-Line refrigeration produc t . A pioneer in t he field for more than 40 years, U- Line Corporation is the world’ s number one manufacturer of built -i n, under- c ounter , specialty refrige ration and ice making products. U-Li ne dedicates 100% of its researc h and deve lopment to these p[...]

BI95, BI98, SP18 3 Introduction ...... ...................... ....................... ...................... ....................... .................. .............2 Warranty Registra t ion ............... ....................... ...................... ....................... ....................2 Please Rec ord Your Model Information .... .......[...]

4 BI95, BI98, SP18 This page intentionally left blank[...]

BI95, BI98, SP18 5 IMPORT ANT IMPORT ANT PLEASE READ all instructions completely befo r e attempting to install, operate, or serv ice your unit. • Pro p er installation proc edures must be followed if this unit is being initially installed, or is moved to a new lo cation afte r bein g in se rvice. An INST ALL A TION GUIDE for your unit, providing[...]

6 BI95, BI98, SP18 Origins Ice Maker Models BI95, BI9 8, SP18 All Origins Ic e Makers provide high daily ice production and storage c apabilities, and conser ve on water , using only 2-3/ 4 gallons (10 .4 L) to produ ce approximat ely 22 lbs (10 kg) of ice . • Model 95 pro duces up to 23 lbs (10.4 kg) o f ice per day and will s tore 12 lbs (5.4 k[...]

BI95, BI98, SP18 7 Model SP18 T o t urn the unit on or o ff, press the rocker switch (Figure 3) located in the center of the lowe r grille. Ice Harvest Control Adjust ments are not nor mally needed. Th e control is preset at the factory . IMPORT ANT IMPORT ANT Making adjustment s may affect the daily ice production of the unit . Figure 4 Models 95 [...]

8 BI95, BI98, SP18 Normal Oper ating Sounds All models in c orporate r igid foam i nsulated cabinets to provide hig h thermal effic iency and maximum sound reduction for its interna l working components. In spite of this technolo gy , your mode l may make sou nds that are unfami liar . Normal o perating soun ds may be mor e noticeable because of th[...]

BI95, BI98, SP18 9 Product Disposal If the unit is be ing removed from service for d isposal, check and ob ey all Federal, Stat e and/or Local regulations regarding the disposal and recycling of r efrigeration appliances, a nd follow these steps completely: 1. Disconnect pow er to the unit and unp lug the power cord from its outlet. 2. Shut off wat[...]

10 BI95, BI98, SP18 Maintenance Proper main t enance of y our U-Line product will ensure ef ficiency , top pe rformance and long life. The maintenance intervals listed are based on normal conditions. Y ou may want to shorten the in t ervals if y ou have pe t s or other sp ecial considerations. Defrost ing Manual Defrost Models - Ev ery T wo Months [...]

BI95, BI98, SP18 11 6. Insert the grille scre w (Figure 8, 1) and tighten. Do not over - tighten. 7. Reconnect power to the unit. Ice Maker Maintenance Inlet Screen Interval - Every T welve Months The solenoid valve inlet screen must be cleaned at least once ea ch year as follow s: WA R N IN G Disconnect electrical power to the unit befor e cleanin[...]

12 BI95, BI98, SP18 Ice Cube Thick ness Adjustment Interval - As Requir ed The ice cube size may be adjusted by changin g the amount of water injected into the ice mak e r assembly as follows: Fig ure 12 1. R emove the ic e make r ass embl y cover (Figure 12) . Fig ure 13 2. Locate the adjusting screw on the ice maker assembly control box. The adju[...]

BI95, BI98, SP18 13 Door Alignment Check and Adjustment IMPORT ANT IMPORT ANT Pr op erly aligned, the door’ s gasket should be firmly in contact w ith the cabinet all the way ar ound the door (no gaps). Carefully examine the door’ s gasket to assure that it is firmly in contact with the cabinet. Also make sur e the door gasket is not pinched on[...]

14 BI95, BI98, SP18 5. Remove screws on opposite side of c abinet (Figure 19) . Note that there may be a nut behind one or both screws on either side. Fig ure 20 6. Install hi nge on opposite side, bottom of cabinet (Figur e 20) . Replace nut on back side where installed. Align hinge outer edge with cabinet before tightening screws . Fig ure 21 7. [...]

BI95, BI98, SP18 15 Before Calling for Service If your U-Line produc t appears to be malfunctionin g, read through the OPERA TION section of this guide to ensure that the functio n of all controls are clearly und erstood. If the malfunction persists, the T ROUBLESHOOTING GUIDE in this guide will a s sist you in qui c kly identify ing common problem[...]

16 BI95, BI98, SP18 T roubleshooting Guide DANGER ELECTROCUTION HA ZARD Never attempt to repair or perform maintenance on the unit until the main electrical power has bee n disconnected. T r oubleshooting - What to check when proble ms occur: PROBLE M POSSIBL E CAUSE REMEDY The unit frosts up. Unit is manual defrost model. Models SP18, 95, 98, CO29[...]

BI95, BI98, SP18 17 This page intentionally left blank[...]

18 BI95, BI98, SP18 This page intentionally left blank[...]

BI95, BI98, SP18 19 U-Line Corpo ration Limited W arra nty U-Line Corpo r ation warran ts each U-Line prod uct to be free from defects in materials and workmanship for a period of one year from the date of purchas e ; and warrants the sealed system (consisting of the compressor , the condenser , the evaporator , the ho t gas bypa ss valve, the drye[...]

For Gener al Inquiries : P .O. Box 245040 Milwaukee, Wisconsin 53224-95 40 U.S.A. Phone (800 ) 779-2 547 FA X (414) 354- 5696 www .U -Line.com For S ervice a nd Parts Assistance: Phone (800 ) 779-2 547 (414) 35 4-0300 FA X (414) 354- 5696 Email: OnLineService@U-Line. c om www .U-Lin eService.com E-mail: OnlinePart s @u-li ne.com For mo re than fo u[...]