Traulsen Traulsen Quality Refrigeration manual

This T raulsen unit is built to our highest quality standards. We build our refrigerators, freezers and heated cabinets this way as a matter of pride. This philosophy has made T raulsen the leader in commercial refrig- eration since 1938. W e thank you for your choice and confidence in T raulsen equipment and we know you will receive many years of [...]

T ABLE OF CONTENTS The serial tag is a permanently affixed sticker on which is recorded vital electrical and refrigeration data about your T raulsen product, as well as the model and serial number . This tag is located in the upper right interior compartment on all reach-in/pass-thru and roll-in/roll-thru refrigerator , freezer and dual-temp models[...]

III. c - INST ALLING LEGS OR CASTERS: 6” high stainless steel legs are supplied standard for all T raulsen reach-in and pass-thru units. Casters in lieu of legs are available as an optional accessory for the same models. These are shipped from the factory packed inside a cardboard box which is strapped to one of the shelves. Remove the nylon stra[...]

III. f - INST ALLING THE CONDENSA TE EV AP (cont’d): holes on the exterior bottom towards the rear of the cabinet. Then, using the four (4) screws provided, at- tach the mounting rails to the cabinet bottom (the end flange is to be up and be facing towards the cabinet rear). Next, place the heater into the heater bracket (note the enclosed spring[...]

IV . a - CLEANING THE CONDENSER (cont’d): two screws located on both sides at the bottom of the louver assembly (see figure 6). Once the screws are removed, the panel can be pivoted upwards allowing full access to the front facing condenser (see figure 7 ) . V acuum or brush any dirt, lint or dust from the finned condenser coil, the compressor an[...]

V . a - ADJUSTING THE SHEL VES: For shelves mounted on pins, first select the desired location and remove the white plastic covers in the interior back and sides by rotating them counter-clock- wise. Remove the shelf pins by rotating them counter- clockwise. Install the pins in the desired location by rotating clockwise. Make sure the pin is secure[...]

-6- VII. SPECIAL TY PRODUCTS - PROOFER/PROOFER RET ARDER MODELS VII. a - INST ALLA TION: MECHANICAL CONNECTION: For plumbing, connect water supply to inlet strainer as marked on top of cabi- net. This connection should be made with a 3/8” male NPT connector . W ater supply pressure should 50 to 80 PSI for best operation. The drain connector locat[...]

-7- VII. SPECIAL TY PRODUCTS - PROOFER/PROOFER RET ARDER MODELS (cont’d) VII. c - OPERA TING THE DIAL HUMIDIST A T (cont’d): When the desired temperature and humidity settings are achieved, the white mode indicating lights will go OFF and you are now ready to proof your product. The mode lights indicate the various stages of operation during th[...]

-8- VII. SPECIAL TY PRODUCTS - PROOFER/PROOFER RET ARDER MODELS (cont’d) VII. d - RET ARDER OPERA TION (cont’d): MANUAL OPERA TION - The T raulsen proofer retarder can also be used in either PROOF or RET ARD mode, regardless of what the 24-hour timer is set for . By switching manually to PROOF or RET ARD, the cabi- net can be run as needed with[...]

-9- VIII. SPECIAL TY PRODUCTS - EVEN-THA W MODELS VIII. a - APPLICA TION OVER VIEW : The Even-Thaw is designed to thaw product at safe temperatures. By keeping the cabinet temperature from rising above 40 o F , the Even-Thaw inputs small amounts of heat while moving large volumes of air around the product. This design allows the product to thaw at [...]

-10- IX. SPECIAL TY PRODUCTS - FISH FILE MODELS IX. a - FISH FILE APPLICA TION: T raulsen fish file models are specifically designed for the storage of fresh fish or poultry in a moist refriger- ated environment, packed in crushed ice, thereby pre- venting dehydration and bacteria growth. For best re- sults, product should be layered between ice st[...]

-1 1- X. SPECIAL TY PRODUCTS - BLAST FREEZER MODELS X. a - BLAST FREEZER APPLICA TION: The roll-in blast freezer models were specifically de- signed for batch processing, where quick freezing is required to help prolong product shelf life. X. b - SPECIAL INST ALLA TION NOTE: Installation should be performed as typical with any other model, see “S[...]

XI. TROUBLE SHOOTING GUIDE FIND YOUR PROBLEM HERE REMEDY 1. Condensing unit fails to start. a. Check if cord & plug has been disconnected. 2. Condensing unit operates for a. Are doors closing properly? prolonged periods or continuously . b. Dirty condenser or filter . Clean properly . c. Evaporator coil iced. Needs to defrost. d. Shortage of re[...]

-13- XII. W ARRANTY INFORMA TION ST ANDARD DOMESTIC W ARRANTY TRAULSEN & CO., INC. warrants new equipment to the original purchaser , when installed within the United States against defective material and workmanship for one (1) year from the date of original installation, not to exceed 15 months from date of shipment. Under this warranty , TRA[...]

XIII. INDEX -14- A Auto Function 7 B Back Flow Prevention Device 6 Batch 1 1 Blast Chiller 1 1 Blast Freeze Mode 1 1 Blast Freezer 1 1 Blower ON/OFF Switch 8 Blower Power Switch 8 C Cleaning 5, 6 Casters 2 Condensate Evaporator 3 Condensate Evaporator , Floor Mounted 1 1 Cord & Plug 3 Compressor Hold Down Provisions 4 Clearance 4 Clock, Setting[...]

T raulsen & Co., Inc. 4401 Blue Mound Road Fort Worth, TX 76106 Phone: (800) 825-8220 Fax-Svce: (817) 740-6757 Website: www .traulsen.com HOURS OF OPERA TION: Monday thru Friday 7:30 am - 4:30 pm CST EXTENDED W ARRANTY SER VICE HOURS Monday thru Friday 4:30 pm - 6:00 pm CST Quality Refrigeration[...]