Toshiba M10 manual

TOSHIBA Satellite Pro M10 Series Portable Personal Computer Maintenance Manual TOSHIBA CORPORATION File Number 960-431[...]

ii Satellite Pro M10 Series Maintenance Manual (960-431) Copyright © 2003 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written perm ission of TOSHIBA. No patent liability is assumed with respect to the use of the inform ation contained herein. TOSHIBA Satellit[...]

Satellite Pro M10 Series Ma intenance Manual (960-431) iii Preface This maintenance manual describes how to perform hardware service maintenance for the TOSHIBA Satellite Pro M10 Series Portable Personal Computer, referred to as Satellite Pro M10 Series in this manual. The procedures described in this manual are intended to help service technicians[...]

iv Satellite Pro M10 Series Maintenance Manual (960-431) The manual is divided into the following parts: Chapter 1 Hardware Overview describes the Satellite Pro M10 Series system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Chapter 3 Test and Diagnostics describes how to perform test and[...]

Satellite Pro M10 Series Ma intenance Manual (960-431) v Conventions This manual uses the following formats to describe, identify, and highlight term s and operating procedures. Acronyms On the first appearance and whenever necessary for clarification acronyms are enclosed in parentheses following their definition. For example: Read Only Memory (RO[...]

vi Satellite Pro M10 Series Maintenance Manual (960-431)[...]

Satellite Pro M10 Series Ma intenance Manual (960-431) vii Table of Contents Chapter 1 Hardware Overview 1.1 Features ................................................................................................................... .1 - 1 1.2 System Unit Block Diagram ...............................................................................[...]

viii Satellite Pro M10 Series Maintenance Manual (960-431) Chapter 3 Tests and Diagnostics 3.1 The Diagnostic Test ................................................................................................. 3-1 3.2 Executing the Diagnostic Test ................................................................................. 3-3 3.3 Subtest N[...]

Satellite Pro M10 Series Ma intenance Manual (960-431) ix Chapter 4 Replacement Procedures 4.1 General .................................................................................................................... .4 - 1 4.2 Memory Modules ................................................................................................... 4-12[...]

x Satellite Pro M10 Series Maintenance Manual (960-431) 4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) .................................. 4-126 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) ..................................... 4-136 4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) ..................................... 4-154 Appendices Appen[...]

Chapter 1 Hardware Overview[...]

1 Hardware Overview 1-ii Satellite Pro M10 Series Maintenance Manual (960-431)[...]

1 Hardware Overview Satellite Pro M10 Series Maintenance Manual (960-431) 1-iii Chapter 1 Contents 1.1 Features................................................................................................................... ....1-1 1.2 System Unit Block Diagram .....................................................................................[...]

1 Hardware Overview 1-iv Satellite Pro M10 Series Maintenance Manual (960-431) Figures Figure 1-1 Front of the computer .....................................................................................1-6 Figure 1-2 System unit configuration...............................................................................1-7 Figure 1-3 System unit[...]

1.1 Features 1 Hardware Overview Satellite Pro M10 Series Mainten ance Manual (960-431) 1-1 1 Features 1.1 Features The TOSHIBA Satellite Pro M10 Series Portable Personal Computer uses extensive Large Scale Integration (LSI), and Compleme ntary Metal-Oxide Sem iconductor (CMOS) technology extensively to provide compact size, minimum weight, low pow[...]

1 Hardware Overview 1.1 Features 1-2 Satellite Pro M10 Series Maintenance Manua l (960-431)  CD-RW/DVD-ROM Drive A full-size, CD-RW/DVD-ROM drive module that lets the user run CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at up to 8 speed and CD-RW at up to 8 speed. For rea[...]

1.1 Features 1 Hardware Overview Satellite Pro M10 Series Mainten ance Manual (960-431) 1-3  Sound system This computer supports software sound (A C97 Audio). The sound system is equipped with AC97 Audio, a CODEC chip, stereo sp eakers, an internal microphone, and jacks for headphone and external microphone. The sound system is equipped with the[...]

1 Hardware Overview 1.1 Features 1-4 Satellite Pro M10 Series Maintenance Manua l (960-431)  Parallel port A Centronics compatible parallel port enab les connection of a prin ter or other parallel device. The port supports Extended Capa bilities Port (ECP) conforming to IEEE- 1284.  Video out This video-out mini-jack enables transfer of NTSC [...]

1.1 Features 1 Hardware Overview Satellite Pro M10 Series Mainten ance Manual (960-431) 1-5  TOSHIBA Console button This button launches an application automa tically. The default is TOSHIBA Console.  TV button This button sets the display devi ce to TV (Video-out). Press it again to return to LCD.  CD/DVD Play button (provi ded with some [...]

1 Hardware Overview 1.1 Features 1-6 Satellite Pro M10 Series Maintenance Manua l (960-431)  Docking interface port A 242-pin, docking interface port enables connection of an optional Advanced Port Replicator II. It provides addition al features as follows: • AC adaptor • One Parallel port • One Serial port • One PS/2 mouse port • One [...]

1.1 Features 1 Hardware Overview Satellite Pro M10 Series Mainten ance Manual (960-431) 1-7 System Board (FQDSY*) Internal Microphone PJ8770 Fan PJ6100 IEEE 1394 PJ8800 AC Adaptor PJ5003 PJ5000 PJ5002 External Microphone PJ2025 Switch Board (FQDSQ*) Sound Board (FQDSD*) PJ2040 PJ4900 Bluetooth PJ1509 HDD PJ1016 RGB PJ5005 PJ5006 Right Speaker PJ500[...]

1 Hardware Overview 1.2 System Unit Block Diagram 1-8 Satellite Pro M10 Series Maintenance Manua l (960-431) 1.2 System Unit Block Diagram Figure 1-3 is a block diagram of the system unit. IMVP4 (V oltage Regulator) ADM1032 (Thermal senser) CPU: Intel P entium M 1.3, 1.4, 1.5, 1.6 GHz Micro FCPGA CK 408 ICS950812 Odem MCH-M Host-AGP Bridge Host-Hub[...]

1.2 System Unit Block Diagram 1 Hardware Overview Satellite Pro M10 Series Mainten ance Manual (960-431) 1-9 The system unit is composed of the following m ajor components:  Processor • Intel Pentium M Processor 1.3GHz – Processor core sp eed: 1.3GHz at 1.35V – Processor bus speed: 400MHz at 1.05V – Integrated L 1 cache memory: 64KB – [...]

1 Hardware Overview 1.2 System Unit Block Diagram 1-10 Satellite Pro M10 Series Mainten ance Manual (960-431) • Intel ICH4-M (I/O Controller Hub) – PCI Rev.2.2 support (6 PCI REQ/GNT pairs) – Bus m aster IDE controller (Ultra ATA 100/66/33) – USB 2.0 controller 6 ports (EHC I: E nhanced Host Controller) – I/O APIC – SMBus Controller –[...]

1.2 System Unit Block Diagram 1 Hardware Overview Satellite Pro M10 Series Mainten ance Manual (960-431) 1-11  Card Controller: • Name: YEBISU3S • This gate array has the following functions and components. – PCI Interface (PCI Rev. 2.2) – Chipset Interface – CardBus/PC Card Controller (Yenta2 Ver. 2.2) – SD Card Controller (SDHC Ver[...]

1 Hardware Overview 1.2 System Unit Block Diagram 1-12 Satellite Pro M10 Series Mainten ance Manual (960-431)  KBC/EC (Keyboard Controller/Embedded Controller) • One M306K9FCLRP chip functions as both KBC and EC. • KBC has the following functions: – Scan controller to check status of keyboard matrix – Interface controller between the key[...]

1.2 System Unit Block Diagram 1 Hardware Overview Satellite Pro M10 Series Mainten ance Manual (960-431) 1-13  CD Play Controller • One OZ168 is used. • The OZ168 allows music CD play while the computer is off.  Sound CODEC • One AD1981B is used. • The AD1981B is an AC'97 Audio CODEC LSI, which is compliant with the industry stan[...]

1 Hardware Overview 1.3 3.5-inch Floppy Disk Drive 1-14 Satellite Pro M10 Series Mainten ance Manual (960-431) 1.3 3.5-inch Floppy Disk Drive The external USB 3.5-inch FDD is a thin, hi gh-performance reliable drive that supports 720KB (formatted) 2DD and 1.44MB (formatted) 2HD disks. The FDD is shown in Figure 1-4. The specifi cations for the FDD [...]

1.4 2.5-inch Hard Disk Drive 1 Hardware Overview Satellite Pro M10 Series Mainten ance Manual (960-431) 1-15 1.4 2.5-inch Hard Disk Drive The removable HDD is a random-access, non-volati le storage device. It has a non-removable 2.5-inch magnetic disk and mini-W inchester type magnetic heads. The computer supports a 30, 40, or 60GB HDD. The HDD is [...]

1 Hardware Overview 1.5 DVD-ROM Dvive 1-16 Satellite Pro M10 Series Mainten ance Manual (960-431) 1.5 DVD-ROM Drive The DVD-ROM drive is capable of driving e ither 12cm (4.72-inch) or 8cm (3.15-inch) DVD/CDs without an adaptor. It reads DVDs at maximum 8-speed and reads CDs at maximum 24-speed. The DVD-ROM drive is shown in Figure 1-6. Specificatio[...]

1.6 Multi Drive 1 Hardware Overview Satellite Pro M10 Series Mainten ance Manual (960-431) 1-17 1.6 Multi Drive The Multi drive accommodates either 12cm (4.72 -inch) o r 8cm (3.15-inch) CDs and CD- R/RWs or DVDs. It reads DVDs at a maximu m 8-speed and CDs at a maximum 24-speed. The Multi drive is shown in Figure 1 -7. Specificat ions for the Multi[...]

1 Hardware Overview 1.6 Multi Drive 1-18 Satellite Pro M10 Series Mainten ance Manual (960-431) Table 1-4 Multi drive specifications (2/2) TEAC DW-224E-36 Item DVD-ROM (Play mode) CD-ROM (Play mode) CD-R/CD-RW (Record mode) ATAPI Burst (Mbytes/s) 33.3 (Ultra DMA mode 2) 16.7 (PIO Mode 4, Multi word DMA mode 2) Access time (ms) Average 1/3 Stroke Ac[...]

1.7 DVD Multi Drive 1 Hardware Overview Satellite Pro M10 Series Mainten ance Manual (960-431) 1-19 1.7 DVD Multi Drive The DVD Multi drive (Panasonic UJ-810BTJ7-A) is capable of driving either 12cm (4.72- inch) or 8cm (3.15-inch) DVD/CDs without an adaptor. The DVD Multi drive is shown in Figure 1-8. Specifications for the DVD Multi drive are list[...]

1 Hardware Overview 1.8 Power Supply 1-20 Satellite Pro M10 Series Mainten ance Manual (960-431) 1.8 Power Supply The power supply distributes 11 different voltages to the system board and performs the following functions: 1. A/D conversion The power supply controller (PSC) uses 10-bit sampling for A/D conversion to determine the following values: [...]

1.8 Power Supply 1 Hardware Overview Satellite Pro M10 Series Mainten ance Manual (960-431) 1-21 6. Power ON/OFF sequence When power is turned on or off, the PSC starts the power on or off sequence. • SQ0-4 = power ON sequence • SQ5-B = power OFF sequence 7. Battery charging control The PSC controls the following. • The quick charge ON/OFF ?[...]

1 Hardware Overview 1.8 Power Supply 1-22 Satellite Pro M10 Series Mainten ance Manual (960-431) The power supply output rating is specified in Table 1-6. Table 1-6 Power supply board output rating Power supplied Yes/No Use Name Voltage (V) Stand by Power off No battery CPU (core) PPV 1.3 No No No CPU (bus), MCH-M, ICH4-M PTV 1.075 No No No VGAC BG[...]

1.9 Batteries 1 Hardware Overview Satellite Pro M10 Series Mainten ance Manual (960-431) 1-23 1.9 Batteries The computer has three types of batteries:  Main battery pack  Optional secondary battery pack (ins talled in the Slim Select Bay)  RTC battery The battery specifications are listed in Table 1-7. Table 1-7 Battery specifications Batt[...]

1 Hardware Overview 1.9 Batteries 1-24 Satellite Pro M10 Series Mainten ance Manual (960-431) 1.9.3 Battery Charging Control Battery charging is controlled by a power s upply microprocessor mounted on the system board. The power supply microprocessor controls wh ether the charge is on or off and detects a full charge when the AC adaptor and battery[...]

1.9 Batteries 1 Hardware Overview Satellite Pro M10 Series Mainten ance Manual (960-431) 1-25  Detection of full charge A full charge is detected when the battery is charging, and unde r any of the following conditions: 1. The battery charging current drop s under the predetermined limit. 2. The charging time exceeds the lim it. 3. The battery?[...]

1 Hardware Overview 1.9 Batteries 1-26 Satellite Pro M10 Series Mainten ance Manual (960-431)[...]

Chapter 2 Troubleshooting Procedures[...]

2 Troubleshooting Procedures 2-ii Satellite Pro M10 Series Maintenance Manual (960-431)[...]

2 Troubleshooting Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 2-iii Chapter 2 Contents 2.1 Troubleshooting ......................................................................................................... 2-1 2.2 Troubleshooting Flowchart .................................................................................[...]

2 Troubleshooting Procedures 2-iv Satellite Pro M10 Series Maintenance Manual (960-431) Procedure 3 Connector and Replacement Check ........................................... 2-42 2.9 Optical Disk Drive Troubleshooting........................................................................ 2-43 Procedure 1 Drive Cleaning Check ....................[...]

2 Troubleshooting Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 2-v Figures Figure 2-1 Troubleshooting flowchart ............................................................................. 2-4 Figure 2-2 Printer port LED .......................................................................................... 2-21 Tables Tabl[...]

2 Troubleshooting Procedures 2-vi Satellite Pro M10 Series Maintenance Manual (960-431)[...]

2.1 Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Mainten ance Manual (960-431) 2-1 2 2.1 Troubleshooting Chapter 2 describes how to dete rmine if a Field R eplaceable Un it (FRU) in the computer is causing the computer to malfunc tion. The FRUs covered are: 1. System Board 5. Display 9. Sound components 2. Floppy Disk Drive[...]

2 Troubleshooting Procedures 2.1 Troubleshooting 2-2 Satellite Pro M10 Series Maintenan ce Manual (960-431) 20. CD-RW media that supports four-speed writi ng and is form atted with DirectCD (media manufactured by RICOH or Mitsubi shi Chem ical are recommended). 21. RJ11 connector checker and modular cable or RJ11 connector checker LED 22. LAN wrapa[...]

2.2 Troubleshooting Flowchart 2 Troubleshooting Procedures Satellite Pro M10 Series Mainten ance Manual (960-431) 2-3 2.2 Troubleshooting Flowchart Use the flowchart in Figure 2-1 as a guide for determ ining which trouble shooting procedures to execute. Before going through the flowchart steps, verify the following:  Ask the user if a password i[...]

2 Troubleshooting Procedures 2.2 Troubleshooting Flowchart 2-4 Satellite Pro M10 Series Maintenan ce Manual (960-431) No No No No Ye s Ye s No No P erform the P ower Supply T roubleshooting Procedures in section 2.3. P erform the P ower Supply T roubleshooting Procedures in section 2.3. P erform the System Board T roubleshooting Procedures in secti[...]

2.2 Troubleshooting Flowchart 2 Troubleshooting Procedures Satellite Pro M10 Series Mainten ance Manual (960-431) 2-5 1 END After confirming which diagnostics test has detected an error , perform the appropr iate procedures as outlined below . Is an error detected by an y of the diagnostics tests? P erform each test. No System is normal. Is an erro[...]

2 Troubleshooting Procedures 2.2 Troubleshooting Flowchart 2-6 Satellite Pro M10 Series Maintenan ce Manual (960-431) If the diagnostics program cannot detect an erro r, the prob lem may be intermittent. Th e Running Test program should be executed several times to isolate the problem . Check the Log Utilities function to confirm which diagnos tic [...]

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Mainten ance Manual (960-431) 2-7 2.3 Power Supply Troubleshooting The power supply controls many functions and com ponents. To determine if the power supply is functioning properly, start with Proc edure 1 and continue with the ot her Procedures as instructed. T[...]

2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting 2-8 Satellite Pro M10 Series Maintenan ce Manual (960-431) Table 2-2 DC IN LED DC IN LED Power supply status Lights green DC power is being supplied from the AC adaptor. Blinks orange Power supply malfunction *3 Doesn’t light Any condition other than those above. *3 When the power supp[...]

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Mainten ance Manual (960-431) 2-9 Procedure 2 Error Code Check If the power supply microprocessor detects a ma lfunction, the DC IN LED blinks orange. The blink pattern indicates an error as shown below.  Start Off for 2 seconds  Error code (8 bit) “1” [...]

2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting 2-10 Satellite Pro M10 Series Mainten ance Manual (960-431)  1st Battery Error code Meaning 20h Main battery overvoltage i s detected. (Not supported) 21h Main battery cha rge current is more than 6.05 A. 22h Main battery discha rge current is more than 0.5 A wh en there is no load. 2[...]

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Mainten ance Manual (960-431) 2-11  1R5-C1V output Error code Meaning 50h 1R5-C1V voltage is over 1.80V when the computer is powered on or off. 51h 1R5-C1V voltage is less than 1.275V when the com puter is powered on. 52h 1R5-C1V voltage is less than 1.275V wh[...]

2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting 2-12 Satellite Pro M10 Series Mainten ance Manual (960-431)  BGVSNS-B1P output Error code Meaning 80h BGVSNS-B1P voltage is over 1.62V when the computer is po wered on or off. 81h BGVSNS-B1P voltage is less than 0. 68V when the computer is powered on. 82h BGVSNS-B1P voltage is less th[...]

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Mainten ance Manual (960-431) 2-13  1R2-P1V output Error code Meaning B0h 1R2-P1V voltage is more than 1.44V when the computer is po wered on or off. B1h 1R2-P1V voltage is less than 1.02V when the computer is powered on. B2h 1R2-P1V voltage is less than 1.02V[...]

2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting 2-14 Satellite Pro M10 Series Mainten ance Manual (960-431) Check 2 In the case of error code 10h or 12h:  Make sure the AC adaptor cord and AC power cord are firmly plugged into the DC IN 15 V socket and wall outlet. If the cables are connected correctly, go to the following step: ?[...]

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Mainten ance Manual (960-431) 2-15 Procedure 3 Connection Check The power supply wiring diagram is shown below: AC adaptor System board PJ8800 AC po wer cord AC adaptor cord Main battery pack Slim Select Bay PJ8810 PJ117 DC-IN Jack 2nd battery pack Any of the con[...]

2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting 2-16 Satellite Pro M10 Series Mainten ance Manual (960-431) Procedure 4 Quick Charge Check The power supply may not charge the battery pack. Perform the following procedures: 1. Reinstall the battery pack. 2. Attach the AC adaptor and turn on the pow er. If you cannot turn on the power, [...]

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Mainten ance Manual (960-431) 2-17 Procedure 5 Replacement Check The system board may be disconnected or dam a ged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures , and perform the following Check 1: Check 1 Replace th[...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-18 Satellite Pro M10 Series Mainten ance Manual (960-431) 2.4 System Board Troubleshooting This section describes how to determ ine if th e system board is defective or not functioning properly. Start with Procedure 1 and continue wi th the other procedures as instructed. The procedure[...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Mainten ance Manual (960-431) 2-19 Procedure 1 Message Check When the power is turned on, the system performs the Initial Reliability Te st (IRT) installed in the BIOS ROM. The IRT tests each IC on the system board and initia lizes it.  If an error message is [...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-20 Satellite Pro M10 Series Mainten ance Manual (960-431) Check 2 The IRT checks the system board. When th e IRT detects an error, the system stops or an error message appears. If one of the following error messages (1) th rough (17), (24) or (25) displays, go to Procedure 4. If error [...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Mainten ance Manual (960-431) 2-21 Procedure 2 Printer Port LED Check on Boot Mode The printer port LED displays the IRT status and test status by turning lights on and off as an eight-digit binary value for boot mode. Figure 2-2 shows the printer port LED. Figur[...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-22 Satellite Pro M10 Series Mainten ance Manual (960-431) Table 2-3 Printer port LE D boot mode status (1/6) LED Status Test item Message FFh Start Register initiali zation for boot block PIT ch.0 initialization BIOS rewrite flag initialization Transition to protected mode Boot block c[...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Mainten ance Manual (960-431) 2-23 Table 2-3 Printer port LE D boot mode status (2/6) LED Status Test item Message CMOS battery level check CMOS checksum CMOS data initialization (1) Set IRT status DRAM size storing in CMOS Resume branch check SM-RAM checksum SMI[...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-24 Satellite Pro M10 Series Mainten ance Manual (960-431) Table 2-3 Printer port LE D boot mode status (3/6) LED Status Test item Message Set SMI table for CPU clock measure D0h Grant SMI (1) Grant SMI (1) Operating clock measure D1h Operating clock measure Set SMI table Grant SMI (2) [...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Mainten ance Manual (960-431) 2-25 Table 2-3 Printer port LE D boot mode status (4/6) LED Status Test item Message Set SETUP item Wait for VGA EC acce ss process completion Power-off switch check EC wake up conditions clear Set processing speed System speaker vol[...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-26 Satellite Pro M10 Series Mainten ance Manual (960-431) Table 2-3 Printer port LE D boot mode status (5/6) LED Status Test item Message 08h Output code generation Output code generation 09h First 64KB memory check First 64KB memor y check 0Ah Interrupting vector initialization Interr[...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Mainten ance Manual (960-431) 2-27 Table 2-3 Printer port LE D boot mode status (6/6) LED Status Test item Message PCI IRQ configuration C0h PnP configuration PnP ISA card configuration C1h Extention I/O ROM check Extention I/O ROM check Store 40 : 00h value (for[...]

2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-28 Satellite Pro M10 Series Mainten ance Manual (960-431) Check 1 If any of the following erro r codes display, go to Procedure 4. B0h, B1h, B2h, B3h, B7h, B8h, 00h, 01h, 02h, 03h, 04h, 06h, 07h, 05h, D0h, D1h, D2h, D3h, D4h, D5h, 70h, 74h, 75h, 71h, 72h, 73h, 76h, 77h, 81h, 82h, 83h, [...]

2.4 System Board Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Mainten ance Manual (960-431) 2-29 Procedure 3 Diagnostic Test Program Execution Check Execute the following tests from the Dia gnostic Test Menu. Refer to Chapter 3, Tests and Diagnostics, for more inform ation on how to perform these tests. 1. System test 2. Me[...]

2 Troubleshooting Procedures 2.5 FDD Troubleshooting 2-30 Satellite Pro M10 Series Mainten ance Manual (960-431) 2.5 FDD Troubleshooting This section describes how to determ ine if th e FDD is functioning properly. Perform the steps below starting with Procedure 1 and continui ng with the other proc edures as required. Procedure 1: FDD Head Cleanin[...]

2.5 FDD Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Mainten ance Manual (960-431) 2-31 Procedure 2 Diagnostic Test Program Execution Check Insert the Diagnostics Disk in the FDD, turn on the computer and run the test. Refer to Chapter 3, Tests and Diagnostics, for more inform ation about th e diagnostics test procedures. F[...]

2 Troubleshooting Procedures 2.5 FDD Troubleshooting 2-32 Satellite Pro M10 Series Mainten ance Manual (960-431) Procedure 3 Connector Check and Replacement Check The 3.5-inch FDD is connected to the USB board. Check 1 Make sure that the FDD cable is firmly connected to the USB port, and that the USB board is firmly connected to the system board. F[...]

2.6 HDD Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Mainten ance Manual (960-431) 2-33 2.6 HDD Troubleshooting This section describes how to determine if th e HDD is functioning properly. Perform the steps below starting with Procedure 1 and continui ng with the other proc edures as required. Procedure 1: Message Check Pro[...]

2 Troubleshooting Procedur es 2.6 HDD Troubleshooting 2-34 Satellite Pro M10 Series Mainten ance Manual (960-431) Procedure 2 Partition Check Insert the TOSHIBA MS-DOS system disk and restart the com puter. Perform the following checks: Check 1 Type C: and press Enter . If you cannot change to drive C, go to Check 2. If you can change to drive C, g[...]

2.6 HDD Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Mainten ance Manual (960-431) 2-35 Procedure 3 Format Check The computer’s HDD is formatted using the MS -DOS FORMAT program. To format the HDD, follow the steps below. Check 1 Format the HDD and transfer system files using FORMAT C:/S/U . If the following message appea[...]

2 Troubleshooting Procedur es 2.6 HDD Troubleshooting 2-36 Satellite Pro M10 Series Mainten ance Manual (960-431) Procedure 4 Diagnostic Test Program Execution Check The HDD test program is stored in the diagnostics disk. Perform all of the HDD tests in the Hard Disk Drive Test. Refer to Chapter 3, Tests and Diagnostics, for m ore information about[...]

2.6 HDD Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Mainten ance Manual (960-431) 2-37 Procedure 5 Connector Check and Replacement Check The HDD or the system board may be disconnect ed or damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and perform the following checks: [...]

2 Troubleshooting Procedures 2.7 Keyboard Troubleshooting 2-38 Satellite Pro M10 Series Mainten ance Manual (960-431) 2.7 Keyboard Troubleshooting To determine if the computer’s keyboard is functioning properly, perform the following procedures. Start with Procedure 1 and conti nue with the other proc edures as instructed. Procedure 1: External K[...]

2.7 Keyboard Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Mainten ance Manual (960-431) 2-39 Procedure 3 Connector and Replacement Check The keyboard, Touch pad, switch board or system board may be disconnected or damaged. Disassemble the computer following the steps described in C hapter 4, Replacement Procedures and perfo[...]

2 Troubleshooting Procedures 2.7 Keyboard Troubleshooting 2-40 Satellite Pro M10 Series Mainten ance Manual (960-431) Check 5 Make sure the switch board I/F cable is firmly connected to the system board and to the switch board. Switch board PJ2025 System board Switch board I/F cable If any of the connections ar e loose, reconnect firmly and repeat [...]

2.8 Display Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Mainten ance Manual (960-431) 2-41 2.8 Display Troubleshooting This section describes how to determ ine if the co mputer’s display is functioning properly. Start with Procedure 1 and continue with th e other procedures as instructed. Procedure 1: External Monitor Ch[...]

2 Troubleshooting Procedures 2.8 Display Troubleshooting 2-42 Satellite Pro M10 Series Mainten ance Manual (960-431) Procedure 3 Connector and Replacement Check The FL, FL inverter board, LCD mo dule, and system board are connected to the display circuits. Any of these components may be dam aged. Refer to Chapter 4, Replacement Procedures, for inst[...]

2.9 Optical Disk Drive Troubleshootin g 2 Troubleshooting Procedures Satellite Pro M10 Series Mainten ance Manual (960-431) 2-43 2.9 Optical Disk Drive Troubleshooting This section describes how to determ ine if the co mputer’s internal optical disk drive (CD-R/RW drive, DVD-ROM drive, Multi drive, DVD-R/-R W drive or DVD-RAM dr ive) is functioni[...]

2 Troubleshooting Procedures 2.9 Optical Disk Drive Troubleshooting 2-44 Satellite Pro M10 Series Mainten ance Manual (960-431) Procedure 3 Connector Check and Replacement Check The optical disk drive is insta lled in the system board. The dr ive may be disconnected, or the drive or system board may be damaged. Disassemb le the computer following t[...]

2.10 Modem Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Mainten ance Manual (960-431) 2-45 2.10 Modem Troubleshooting This section describes how to determ ine if th e computer's m odem is functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other proced ures as required. Proce[...]

2 Troubleshooting Procedures 2.10 Modem Troubleshooting 2-46 Satellite Pro M10 Series Mainten ance Manual (960-431) Procedure 2 Connector Check and Replacement Check The Modem is installed as a modem daughter card (MDC). If the modem m alfunctions, there may be a bad connection between the MDC and the system board. Or the MDC, the system board or t[...]

2.11 LAN Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Mainten ance Manual (960-431) 2-47 2.11 LAN Troubleshooting This section describes how to determ ine if th e computer's LAN port is functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other proced ure as required. Procedur[...]

2 Troubleshooting Procedures 2.11 LAN Troubleshooting 2-48 Satellite Pro M10 Series Mainten ance Manual (960-431) Procedure 2 Connector Check and Replacement Check If the LAN port malfunctions, th ere may be a bad connection betw een the RJ-45/RJ-11 jacks and the System Board. Or the System Board m ay be damaged. Disassemble the computer following [...]

2.12 Sound Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Mainten ance Manual (960-431) 2-49 2.12 Sound Troubleshooting This section describes how to determine if the computer's sound functions are functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required[...]

2 Troubleshooting Procedures 2.12 Sound Troubleshooting 2-50 Satellite Pro M10 Series Mainten ance Manual (960-431) Procedure 2 Connector Check The sound function wiring diagram is shown below: System board Right Speak er PJ5006 Sound board Right speaker cab le PJ5007 PJ5004 PJ5005 Left speaker cab le Left Speaker PJ5002 Internal Mic. Any of the co[...]

2.12 Sound Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Mainten ance Manual (960-431) 2-51 Procedure 3 Replacement Check Check 1 If the stereo speakers don't sound prope rly, the stereo speakers may be defective or damaged. Replace them with new ones. If the stereo speak ers still do not work properly, go to Check 3. C[...]

2 Troubleshooting Procedures 2.13 Bluetooth Troubleshooting 2-52 Satellite Pro M10 Series Mainten ance Manual (960-431) 2.13 Bluetooth Troubleshooting This section describes how to determ ine if th e computer's Bluetooth functions are working properly. Perform the steps below starting with Procedure 1 and continuing with the other procedure as[...]

2.13 Bluetooth Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Mainten ance Manual (960-431) 2-53 Procedure 2 Connector Check and Replacement Check If the Bluetooth function ma lfunctions, there may be a bad connection between the antenna cable, the Bluetooth module, and the system board (FQDSY*). Or the antenna cable or other[...]

2 Troubleshooting Procedures 2.14 Wireless LAN Troubleshooting 2-54 Satellite Pro M10 Series Mainten ance Manual (960-431) 2.14 Wireless LAN Troubleshooting This section describes how to determ ine if the co mputer's W ireless LAN is functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedure[...]

2.14 Wireless LAN Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Mainten ance Manual (960-431) 2-55 Procedure 2 Connector Check and Replacement Check If the Wireless LAN port malfunctions, there m ay be a bad connection between the antenna boards, the Wireless LAN Mini PCI card, and th e system board (FQDSY*). Or the antenna [...]

2 Troubleshooting Procedures 2.14 Wireless LAN Troubleshooting 2-56 Satellite Pro M10 Series Mainten ance Manual (960-431)[...]

Chapter 3 Tests and Diagnostics[...]

3 Tests and Diagnostics 3-ii Satellite Pro M10 Series Maintenance Manual (960-431)[...]

3 Tests and Diagnostics Satellite Pro M10 Series Ma intenance Manual (960-431) 3-iii Chapter 3 Contents 3.1 The Diagnostic Test ................................................................................................... 3-1 3.2 Executing the Diagnostic Test ................................................................................... [...]

3 Tests and Diagnostics 3-iv Satellite Pro M10 Series Maintenance Manual (960-431) 3.25.2 Operations .......................................................................................... 3-69 3.26 Floppy Disk Drive Utilities...................................................................................... 3-71 3.26.1 Function Description .[...]

3.1 The Diagnostic Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-1 3 3.1 The Diagnostic Test This chapter explains how to use the Diagnostic Test program to test the functions of the computer’s hardware modules. The Diagnostic Test Program is stored on the Diagnostic Disk. The Diagnostic Test program consist[...]

3 Tests and Diagnostics 3.1 The Diagnostic Test 3-2 Satellite Pro M10 Series Maintenance Manual (960-431) You will need the following equipment to perform som e of the Diagnostic test programs.  The Diagnostics Disk (all tests)  A formatted working disk for the floppy disk drive test  An external FDD attachment  A cleaning kit to clean [...]

3.2 Executing the Diagnostic Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-3 3.2 Executing the Diagnostic Test Toshiba MS-DOS is required to run the DIAGNOSTICS TEST PROGRAM. To start the DIAGNOSTIC TEST PROGRAM, follow these steps: 1. Insert the Diagnostics disk in the floppy disk drive and turn on the comput[...]

3 Tests and Diagnostics 3.2 Executing the Diagnostic Test 3-4 Satellite Pro M10 Series Maintenance Manual (960-431) 2. To execute the DIAGNOSTIC TEST MENU from the DIAGNOSTICS MENU, set the highlight bar to 1 , and press Enter . The following DIAGNOSTIC TEST MENU will appear: TOSHIBA Personal Computer xxxxxxx DIAGNOSTICS Version X.XX (C) Copyright [...]

3.2 Executing the Diagnostic Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-5 3. Select the option you want to execute and press Enter . When “1-SYSTEM TEST” is selected, the following message will appear: SUB-TEST MENU : 01 - ROM checksum 02 - Dock/Undock 03 - 04 - Fan ON/OFF 05 - Geyserville 06 - Quick ch[...]

3 Tests and Diagnostics 3.2 Executing the Diagnostic Test 3-6 Satellite Pro M10 Series Maintenance Manual (960-431) 5. The following message will appear: ERROR STOP : YES/NO Then, use the left or right arrow keys to move the cursor to the desired option and press Enter . Selecting YES stops the test program when an error is found and displays the o[...]

3.3 Subtest Names 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-7 3.3 Subtest Names Table 3-1 lists the subtest names for each test program in the DIAGNOSTIC TEST MENU. Table 3-1 Subtest names (1/3) No. Test Name Subtest No. Subtest Name 1 SYSTEM 01 02 04 05 06 07 08 10 ROM checksum Dock/Undock Fan ON/OFF Geyservil[...]

3 Tests and Diagnostics 3.3 Subtest Names 3-8 Satellite Pro M10 Series Maintenance Manual (960-431) Table 3-1 Subtest names (2/3) No. Test Name Subtest No. Subtest Name 7 ASYNC 01 02 03 04 06 07 Wrap around (board) Point to Point (send) Point to Point (receive) Interrupt test FIR/SIR Point to point (send) FIR/SIR Point to point (receive) 8 HARD DIS[...]

3.3 Subtest Names 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-9 Table 3-1 Subtest names (3/3) No. Test Name Subtest No. Subtest Name - Wireless LAN (Agere) 1 2 3 0 Transmit & Receive test [Responder] MAC Address test [Mini-P CI Wireless LAN] Wireless LAN (WEP64/128) test Transmit & Receive test [Initiator[...]

3 Tests and Diagnostics 3.4 System Test 3-10 Satellite Pro M10 Series Maintenance Manual (960-431) 3.4 System Test To execute the System Test select 1 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter. Subtest 01 ROM Checksum This subtest exe[...]

3.4 System Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-11 Subtest 07 DMI read Reads the factory setting for the serial and DMI numbers. Model Name : XXXXXX Version Number : XXXXXX-XXXXX Serial Number : XXXXXXXXXX Model Number : XXXXXX-XXXXX PCN/BND Number : XXXXXXXXXXXXXXXXXXXX UUID Number : XXXXXXXXXXXXXXXX[...]

3 Tests and Diagnostics 3.4 System Test 3-12 Satellite Pro M10 Series Maintenance Manual (960-431) Subtest 10 CPU Temperature This subtest measures the CPU temperature to see if the cooling functions of the computer are effectively working. When the subtest starts, the following message appears on the display: CPU TEMP = XX deg C Throttling level =[...]

3.5 Memory Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-13 3.5 Memory Test To execute the Memory Test, select 2 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter. Subtest 01 Conventional memory This sub[...]

3 Tests and Diagnostics 3.5 Memory Test 3-14 Satellite Pro M10 Series Maintenance Manual (960-431) Subtest 04 Cache Memory To test the cache memory, a pass-through write-read com parison of ‘5A’ data is run repeatedly to the test area (‘7000’:‘Program’ size to ‘7000’:‘7FFF’ (32 KB)) to check the hit-miss ratio (on/off status) fo[...]

3.6 Keyboard Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-15 3.6 Keyboard Test To execute the Keyboard Test, select 3 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 Pressed Key Display N[...]

3 Tests and Diagnostics 3.6 Keyboard Test 3-16 Satellite Pro M10 Series Maintenance Manual (960-431) Subtest 02 Pressed Key Code Display When a key is pressed, the scan code, character code, and key top name are displayed on the screen in the format shown below. The Ins, Caps Lock , Num Lock, Scroll Lock, Alt, Ctrl, Left Shift , and Right Shift key[...]

3.6 Keyboard Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-17 Subtest 04 Touch Pad This Subtest checks the functions of the touch pad as shown below. A) Touch Pad pressure sensing direction and parameter. B) Touch Pad switch function check. This test reports the pointing stick motion response from the touch pa[...]

3 Tests and Diagnostics 3.6 Keyboard Test 3-18 Satellite Pro M10 Series Maintenance Manual (960-431) Subtest 05 USB Test ( Port0,Port1 ) test This Subtest checks USB. The USB TEST Module (ZD0003P01) and USB Cable (ZD0003P02) must be connected to the computer. The following message will appear. Select a port to test and press Enter . Test port numbe[...]

3.6 Keyboard Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-19 Subtest 07 Button Test When this subtest displays messages shown below in order, press the corresponding button. NOTE : This subtest must be completed within 10 seconds. Press [CD] button Press [MP3] button Press [Back] button Press [Play] button Pr[...]

3 Tests and Diagnostics 3.7 Display Test 3-20 Satellite Pro M10 Series Maintenance Manual (960-431) 3.7 Display Test To execute the Display Test, select 4 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. The Display test contains seven subtests that test the display in various modes. Move the highlight bar to the [...]

3.7 Display Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-21 Subtest 04 Gradation & Mode test for VGA This subtest displays gradations for each mode. Execute the test, then press Enter to change the mode. The display below appears on the screen when this subtest is executed. Pressing Enter changes the size[...]

3 Tests and Diagnostics 3.7 Display Test 3-22 Satellite Pro M10 Series Maintenance Manual (960-431) Pressing Enter changes the size of the displayed image. [ Mode 3 ] Pressing Enter changes the size of the displayed image in the following order: Mode 111 640*480 64K Mode 112 640*480 16M Mode 114 800*600 64K Mode 115 800*600 16M Mode 117 1024*768 64[...]

3.7 Display Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-23 Subtest 06 “H” Pattern Display This subtest displays a full screen of “H” patterns. HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHH[...]

3 Tests and Diagnostics 3.8 Printer Test 3-24 Satellite Pro M10 Series Maintenance Manual (960-431) 3.8 Printer Test To execute the Printer Test, select 6 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. The Printer Test contains three subtests that test the output of the printer connected to the computer. The fol[...]

3.8 Printer Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-25 Subtest 02 Function This subtest is for IBM compatible printers, and tests the following f unctions: Normal print Double-width print Compressed print Emphasized print Double-strike print All characters print This subtest prints the various print type[...]

3 Tests and Diagnostics 3.9 Async Test 3-26 Satellite Pro M10 Series Maintenance Manual (960-431) 3.9 Async Test To execute the Async Test, select 7 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions displayed on the screen. The Async test contains two subtests that test the asynchronous communication functions. Move the highlight[...]

3.9 Async Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-27 Subtest 06 FIR/SIR Point to Point (send) NOTE: To execute subtests 06 and 07, each computer must have access to the other computer’s infrared port. This subtest sends 20h through 7Eh data to the receive side, then receives the sent data and compares [...]

3 Tests and Diagnostics 3.10 Hard Disk Test 3-28 Satellite Pro M10 Series Maintenance Manual (960-431) 3.10 Hard Disk Test To execute the Hard Disk Test, select 8 from the DIAGNOSTIC TEST MENU, press Enter , and follow the directions on the screen. The hard disk test contains ten subtests that test the hard disk drive functions. NOTE : To execute t[...]

3.10 Hard Disk Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-29 3. The Hard Disk Test message will appear after you respond to the Detail Status prompt. Select the number of the subtest you want to execute and press Enter . The following message will appear during each subtest. HARD DISK TEST XXXXXXX SUB-TEST [...]

3 Tests and Diagnostics 3.10 Hard Disk Test 3-30 Satellite Pro M10 Series Maintenance Manual (960-431) Subtest 04 Cross Talk & Peak Shift This subtest writes eight types of worst pattern data (listed below) to a cylinder, then reads the data while moving from cylinder to cylinder. Worst pattern data Cylinder ‘B5ADAD’ 0 cylinder ‘4A5252’[...]

3.11 Real Timer Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-31 3.11 Real Timer Test To execute the Real Timer Test, select 9 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. The real timer test contains three Subtests that test the computer’s real timer functions. Move th[...]

3 Tests and Diagnostics 3.11 Real Timer Test 3-32 Satellite Pro M10 Series Maintenance Manual (960-431) Subtest 03 Real Time Carry CAUTION : When you execute this Subtest, the current date and time are erased. This Subtest checks the real time clock increments, m aking sure the date and time are displayed in the following form at: Current date : 12[...]

3.12 NDP Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-33 3.12 NDP Test To execute the NDP test, select 10 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. The NDP test contains one Subtest that tests the computer’s NDP functions. Subtest 01 NDP This test checks the follow[...]

3 Tests and Diagnostics 3.13 Expansion Test 3-34 Satellite Pro M10 Series Maintenance Manual (960-431) 3 3.13 Expansion Test To execute the expansion test, select 11 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. The expansion test contains two subtests. NOTE: To execute this subtest, the PC card wraparound con[...]

3.14 CD-ROM/DVD-ROM Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-35 3.14 CD-ROM/DVD-ROM Test To execute the CD-ROM/DVD-ROM test, select 13 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the scree n. The CD-ROM/DVD-ROM test contains six Subtests that test the computer’s CD-ROM/DVD-R[...]

3 Tests and Diagnostics 3.15 LAN Test 3-36 Satellite Pro M10 Series Maintenance Manual (960-431) 3.15 LAN Test To execute the LAN test, select 14 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. The LAN test contains one Subtest that tests the computer’s LAN function. Subtest 01 MAC Display This Subtest display[...]

3.16 Wireless LAN Test (Agere) 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-37 3.16 Wireless LAN Test (Agere) This section describes how to perform the wireless LAN transm itting-receiving test with the test program. Note: Use another computer (with Agere wireless LAN card) that can communicate by the wireless LAN[...]

3 Tests and Diagnostics 3.16 Wireless LAN Test (Agere) 3-38 Satellite Pro M10 Series Maintenance Manual (960-431) Subtest 01 Transmit & Receive test This sub test checks transmit and receive functions. Transmit test Press 1 to select the test and press Enter in the target machine as a responder. The following message will appear: ##############[...]

3.16 Wireless LAN Test (Agere) 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-39 When the machine has passed the test, “OK” m essage will appear in the test machine. Then press Enter in the target machine; the “OK” me ssage will appear also in the target machine. Press Enter to return to the main menu. Recei[...]

3 Tests and Diagnostics 3.16 Wireless LAN Test (Agere) 3-40 Satellite Pro M10 Series Maintenance Manual (960-431) Press 0 to select the test and press Enter in the target machine. The following message will appear: ############################################################# #### Wireless LAN sub system repair test VX.XX #### #####################[...]

3.16 Wireless LAN Test (Agere) 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-41 Subtest 02 Mac Address test This subtest reads MAC Address. If there is no problem, the “OK” message will appear. Subtest 03 Wireless LAN (WEP64/128) test This subtest reads the WEP of the wireless LAN card installed in the target m[...]

3 Tests and Diagnostics 3.17 Wireless LAN Test (Atheros) 3-42 Satellite Pro M10 Series Maintenance Manual (960-431) 3.17 Wireless LAN Test (Atheros) This section describes how to perform the wireless LAN transm itting-receiving test with the test program. Note: Use another computer (with Atheros wireless LAN card) that can communicate by the wirele[...]

3.17 Wireless LAN Test (Atheros) 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-43 Setting the responder machine Note: Release the write-protection of the floppy disk for the test. Insert a floppy disk containing the test program into the FDD for the responder machine and turn on the responder machine. The Wireless [...]

3 Tests and Diagnostics 3.17 Wireless LAN Test (Atheros) 3-44 Satellite Pro M10 Series Maintenance Manual (960-431) When the tester machine has passed the test, "OK" m essage will appear in the tester machine. Press Enter to return to the main menu. When the tester machine has not passed the test, "NG" m essage will appear in th[...]

3.18 Sound/LAN/Modem Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-45 3.18 Sound/LAN/Modem Test This section describes how to perform the Sound/LAN/Modem test with the test program . CAUTION : The system is capable of producing high volume sound. When you use a headphone, be careful to set the volume low and a[...]

3 Tests and Diagnostics 3.18 Sound/LAN/Modem Test 3-46 Satellite Pro M10 Series Maintenance Manual (960-431) Subtest 01 Microphoned recording & play This subtest checks the function of the CODEC A/D D/A converter. Both the microphone and headphone terminal can be checked at the sam e time. Before executing this subtest, connect an external micr[...]

3.18 Sound/LAN/Modem Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-47 To execute a subtest continuously, select the test number and press Enter. To exit the Sound/LAN/Modem test, remove the test program disk from the USB FDD and turn the computer off. Subtest 02 Sin Wave This subtest is executed by the load fo[...]

3 Tests and Diagnostics 3.18 Sound/LAN/Modem Test 3-48 Satellite Pro M10 Series Maintenance Manual (960-431) Subtest 03 LAN Test (a) Select 3 to execute and press Enter . The following m essage will appear: COMPLETED Repeat count = 00000 Error count = 00000 XXXX (XXXXX) LAN TEST Vol.X.XX 100Mbps Auto-negotiation TxRx Test Destination Address = xxxx[...]

3.18 Sound/LAN/Modem Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-49 Subtest 04 Modem Test (a) Select 4 to execute and press Enter . The following m essage will appear: ICH MDC Test Program with Modem Sound ( PCB Interface ) Version X.X * Scorpio Modem Initialize :OK * Digital Loopback Test :OK * Modem Sound [...]

3 Tests and Diagnostics 3.19 IEEE1394 Test Program 3-50 Satellite Pro M10 Series Maintenance Manual (960-431) 3.19 IEEE1394 Test Program This section describes how to perform the IEEE1394 test with the test program. Toshiba MS-DOS is required to run the DIAGNOSTICS TEST PROGRAM. To start the DIAGNOSTIC TEST PROGRAM, follow these steps: (a) Insert t[...]

3.19 IEEE1394 Test Program 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-51 Subtest 01 IEEE1394 test This program checks the data transporting between responder machine and target machine. NOTE: Use another computer that can communicate by IEEE1394 (i. Link) cable as a reference machine to perform this test. Subtes[...]

3 Tests and Diagnostics 3.20 Bluetooth Test 3-52 Satellite Pro M10 Series Maintenance Manual (960-431) 3.20 Bluetooth Test This section describes how to perform the Bluetooth test program to check if the Bluetooth functions of computer are working properly. To start the Bluetooth test program, follow the steps below: NOTE: Use another computer that[...]

3.20 Bluetooth Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-53 Subtest 01 BD_ADDR check This subtest checks the BD_ADDR functions. When the Bluetooth test menu is displayed, press 1 to select the test and press Enter . The following message will appear: --------------------------------------------------------[...]

3 Tests and Diagnostics 3.20 Bluetooth Test 3-54 Satellite Pro M10 Series Maintenance Manual (960-431) If the target machine has any problem, it displays Error CODE . The following message is desplayed. ----------------------------------------------------------------------------- Bluetooth Subsystem T&D for PCSE(BD_ADDR) VerX.XX Copyright (C) b[...]

3.20 Bluetooth Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-55 If the machine detects a malfunction, it indicates the error code as shown below. The error code begins with the least significant digit. Error code Table 3-2 Error code for Bluetooth test (BD_ADDR) (1/2) Error code Meaning 0x01 Unknown HCI Comm a[...]

3 Tests and Diagnostics 3.20 Bluetooth Test 3-56 Satellite Pro M10 Series Maintenance Manual (960-431) Table 3-2 Error code for Bluetooth test (BD_ADDR) (2/2) Error code Meaning 0x20 Unsupported LMP Parameter Val ue. 0x21 Role Change Not Allowed. 0x22 LMP Response Timeout. 0x23 LMP Error Transaction Collosion. 0x24 LMP PDU Not Allowed. 0x25 Not Exi[...]

3.20 Bluetooth Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-57 When the Bluetooth test menu is displayed, press T to select the test and press Enter in the test machine. The following m essage will appear: ----------------------------------------------------------------------------- Bluetooth Subsystem T&[...]

3 Tests and Diagnostics 3.20 Bluetooth Test 3-58 Satellite Pro M10 Series Maintenance Manual (960-431) If the target machine has any problem, the following m essage “ INCOMPLETE ” is displayed with the Error CODE . ----------------------------------------------------------------------------- Bluetooth Subsystem T&D for PCSE(CS-Air) VerX.XX [...]

3.20 Bluetooth Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-59 If the machine detects a malfunction, it indicates the error code as shown below. The error code begins with the least significant digit. Error code Table 3-3 Error code for Bluetooth test (BD_ADDR of the DUT) (1/2) Error code Meaning 0x01 Unknown[...]

3 Tests and Diagnostics 3.20 Bluetooth Test 3-60 Satellite Pro M10 Series Maintenance Manual (960-431) Table 3-3 Error code for Bluetooth test (BD_ADDR of the DUT) (2/2) Error code Meaning 0x20 Unsupported LMP Parameter Value. 0x21 Role Change Not Allowed. 0x22 LMP Response Timeout. 0x23 LMP Error Transaction Collosion. 0x24 LMP PDU Not Allowed. 0x[...]

3.21 Error Code and Error Status Names 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-61 3.21 Error Code and Error Status Names Table 3-4 lists the error codes and error status names for the Diagnostic Test. Table 3-4 Error codes and error status names (1/3) Device name Error code Error status name (Common) FF Data [...]

3 Tests and Diagnostics 3.21 Error Code and Error Status Names 3-62 Satellite Pro M10 Series Maintenance Manual (960-431) Table 3-4 Error codes and error status names (2/3) Device name Error code Error status name FDD 01 02 03 04 06 08 09 10 20 40 60 80 EE Bad Command Error Address Mark Not Found Write Protected Record Not Found Media Removed DMA O[...]

3.21 Error Code and Error Status Names 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-63 Table 3-4 Error codes and error status names (3/3) Device name Error code Error status name NDP 01 02 03 04 05 06 No Co-Processor Control Word Error Status Word Error Bus Error Addition Error Multiply Error Expansion C1 C4 C5 C6[...]

3 Tests and Diagnostics 3.22 Hard Disk Test Detail Status 3-64 Satellite Pro M10 Series Maintenance Manual (960-431) 3.22 Hard Disk Test Detail Status When an error occurs in the hard disk test, the following message is displayed: HDC status = XXXXXXXX Detailed information about the hard disk test error is displayed on the screen by an eight-digit [...]

3.22 Hard Disk Test Detail Status 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-65 Table 3-6 Error register contents Bit Name Description 7 BBK1 (Bad block mark) “0” … Not used “1” … A bad block mark is detected. 6 UNC (Uncorrectable) “0” … There is no uncorrectable data error. “1” … Uncorre[...]

3 Tests and Diagnostics 3.23 Head Cleaning 3-66 Satellite Pro M10 Series Maintenance Manual (960-431) 3.23 Head Cleaning 3.23.1 Function Description This function cleans the heads in the FDD by executing a series of head load/seek and read operations. A cleaning kit is necessary to perform this program. 3.23.2 Operations 1. Selecting test 4 from th[...]

3.24 Log Utilities 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-67 3.24 Log Utilities 3.24.1 Function Description This function logs error information generated while a test is in progress and stores the results in RAM. This function can store data on a floppy disk or output the data to a printer. If the power swi[...]

3 Tests and Diagnostics 3.24 Log Utilities 3-68 Satellite Pro M10 Series Maintenance Manual (960-431) 2. The error information displayed on the screen can be manipulated by the following number keys: 1 scrolls the display to the next page. 2 scrolls the display to the previous page. 3 returns to the Diagnostic Menu. 4 erases all error log informati[...]

3.25 Running Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-69 3.25 Running Test 3.25.1 Function Description This function automatically executes the following tests in sequence: 1. System test (subtest 01) 2. Memory test (subtests 01, 02, 04, and 06) 3. Real timer test (subtest 02) 4. Display test (subtest 01)[...]

3 Tests and Diagnostics 3.25 Running Test 3-70 Satellite Pro M10 Series Maintenance Manual (960-431) 4. Select No and press Enter . The following message will appear: Mount the work disk(s) on the drive(s), then press [Enter] key. [Warning : The contents of the disk(s), will be destroyed.] 5. This program is executed continuously. To terminate the [...]

3.26 Floppy Disk Drive Utilities 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-71 3.26 Floppy Disk Drive Utilities 3.26.1 Function Description This function formats the FDD, copies the floppy disk and displays the dump list for both the FDD and HDD. 1. FORMAT NOTE : This program is only for testing a floppy disk dr[...]

3 Tests and Diagnostics 3.26 Floppy Disk Drive Utilities 3-72 Satellite Pro M10 Series Maintenance Manual (960-431) 3.26.2 Operations 1. Selecting 7 from the DIAGNOSTIC MENU and pressing Enter displays the following message: [ FDD UTILITIES ] 1 - FORMAT 2 - COPY 3 - DUMP 4 - HDD ID READ 9 - EXIT TO DIAGNOSTICS MENU 2. FORMAT program (a) Selecting F[...]

3.26 Floppy Disk Drive Utilities 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-73 3. COPY program (a) When COPY is selected, the following message appears: FLOPPY DISK FORMAT & COPY : VX.XX Type select (0:2DD,3:2HD) ? (b) Selecting a media/drive type num ber will display a message similar to the one below: Inse[...]

3 Tests and Diagnostics 3.26 Floppy Disk Drive Utilities 3-74 Satellite Pro M10 Series Maintenance Manual (960-431) 4. DUMP program (a) When DUMP is selected, the following message appears: DIAGNOSTICS-HARD DISK & FLOPPY DISK DUMP : VX.XX Drive type select (1:FDD, 2:HDD) ? (b) When FDD is selected, the following m essage appears. Select a forma[...]

3.26 Floppy Disk Drive Utilities 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-75 5. HDD-ID READ Selecting HDD ID READ displays th e following HDD ID configuration: [HDD ID Read (VX.XX)] [Drive #X] ID code (h) = XXXX No. of Cylinders = XXXX XXXX Removable Cylinders = XXXX XXXX No. of Heads = XXXX XXXX Unformat Byte[...]

3 Tests and Diagnostics 3.27 System Configuration 3-76 Satellite Pro M10 Series Maintenance Manual (960-431) 3 3.27 System Configuration 3.27.1 Function Description The System Configuration program contains th e following configuration information for the computer: 1. Processor Type 2. VGA Controller 3. MS-DOS Version 4. BIOS ROM version (1st ID, 2[...]

3.27 System Configuration 3 Tests and Diagnostics Satellite Pro M10 Series Ma intenance Manual (960-431) 3-77 3.27.2 Operations Selecting 8 from the DIAGNOSTIC MENU and pressing Enter displays the following system configuration: System Configuration Display : Ver x.xx [Machine Name : ] ---------------------------------------------------------------[...]

3 Tests and Diagnostics 3.28 SETUP 3-78 Satellite Pro M10 Series Maintenance Manual (960-431) 3.28 SETUP 3.28.1 Function Description This program displays the current system setup inform ation as listed below: 1. Memory (a) Total 2. System Date/Time (a) Date (b) Time 3. Battery (a) Battery Save Mode 4. Password 5. HDD Password (a) HDD (b) HDD Passw[...]

3.28 SETUP 3 Tests and Diagnostics Satellite Pro M10 Series Ma intenance Manual (960-431) 3-79 11. Drives I/O (a) Built-in HDD (b) Select Bay 12. PCI Bus (a) PCI Bus 13. PC Card (a) Controller Mode 14. Peripheral (a) Internal Pointing Device (b) Parallel Port Mode (c) Hard Disk Mode 15. Legacy Emulation (a) USB keyboard/Mouse Legacy Emulation (b) U[...]

3 Tests and Diagnostics 3.28 SETUP 3-80 Satellite Pro M10 Series Maintenance Manual (960-431) 3.28.2 Accessing the SETUP Program Selecting 0 from the DIAGNOSTICS MENU and pressing Enter displays the TSETUP screen. The TSETUP screen is divided into two pages: SYSTEM SETUP (1/2) and SYSTEM SETUP (2/2). SYSTEM SETUP (1/2) ACPI BIOS version - x.xx MEMO[...]

3.28 SETUP 3 Tests and Diagnostics Satellite Pro M10 Series Ma intenance Manual (960-431) 3-81 SYSTEM SETUP (2/2) ACPI BIOS version - x.xx CONFIGURATION PC CARD Device Config. = Setup by OS Controller Mode = Auto-Selected I/O PORTS PERIPHERAL Serial = COM1(3F8H/IRQ4) Internal Pointing Device = Enabled Parallel = LPT1(378H/IRQ7/CH3) Ext Keyboard &qu[...]

3 Tests and Diagnostics 3.28 SETUP 3-82 Satellite Pro M10 Series Maintenance Manual (960-431) Moving Within the SETUP Menu and Changing Values 1. Press Å and Æ to move between the two columns. Press PgDn and PgUp to m ove between the two pages. Press ↑ and ↓ to move between items in a colum n. 2. Press either the space bar to change the value[...]

3.28 SETUP 3 Tests and Diagnostics Satellite Pro M10 Series Ma intenance Manual (960-431) 3-83 SETUP Options The SETUP screen is divided into functionally related groups. This section describes each group and its options. 1. Memory This group of options displays the computer’s mem ory. (a) Total This field displays the total amount of mem ory ins[...]

3 Tests and Diagnostics 3.28 SETUP 3-84 Satellite Pro M10 Series Maintenance Manual (960-431) Display Auto Off Use this option to disable or set the duration of the display automatic power off function. This function causes the computer to turn the LCD panel’s illumination off if you make no entry for the set period of tim e. Disabled Disables di[...]

3.28 SETUP 3 Tests and Diagnostics Satellite Pro M10 Series Ma intenance Manual (960-431) 3-85 4. Password This option allows you to set or reset the user password for power on. Not Registered Change or remove the password. (Default) For details on setting the user password refer to the User’s Manual. 5. HDD Password This group of options display[...]

3 Tests and Diagnostics 3.28 SETUP 3-86 Satellite Pro M10 Series Maintenance Manual (960-431) (b) HDD Priority This option enables to select the priority for the Built-in HDD, optional second HDD or PC card. Built-in HDD → Second HDD → PC Card (Default) Second HDD → Built-in HDD → PC Card Built-in HDD → PC Card → Second HDD Second HDD ?[...]

3.28 SETUP 3 Tests and Diagnostics Satellite Pro M10 Series Ma intenance Manual (960-431) 3-87 (c) TV Type This option lets you make settings for television display. NTSC(US) (Default) NTSC(JAPAN) PAL 8. Others Whether or not you need to configure the computer with these options depends primarily on the kind of software or peripherals you use. (a) [...]

3 Tests and Diagnostics 3.28 SETUP 3-88 Satellite Pro M10 Series Maintenance Manual (960-431) (c) Level 2 Cache Use this option to enable or disable the level 2 cache. Enabled Enables the level 2 cache. (Default) Disabled Disables the level 2 cache. (d) Dynamic CPU Frequency Mode Use this option to choose from the following settings: Dynamically Sw[...]

3.28 SETUP 3 Tests and Diagnostics Satellite Pro M10 Series Ma intenance Manual (960-431) 3-89 (f) Panel Power On/Off This option lets you set the Panel Power On/Off function. It is effective only in Resume mode. Enabled Enables the Panel Power On/Off. Disabled Disables the Panel Power On/Off (Default) 9. Configuration This field displays the confi[...]

3 Tests and Diagnostics 3.28 SETUP 3-90 Satellite Pro M10 Series Maintenance Manual (960-431) COM level Interrupt level I/O address COM1 4 3F8H (Serial port default) COM2 3 2F8H COM3 4 3E8H COM3 5 3E8H COM3 7 3E8H COM4 3 2E8H COM4 5 2E8H COM4 7 2E8H Not Used Disables port (b) Parallel This option sets the interrupt request level (IRQ) and I/O port [...]

3.28 SETUP 3 Tests and Diagnostics Satellite Pro M10 Series Ma intenance Manual (960-431) 3-91 For most printers, the port should be set to ECP . W ith some other parallel devices, the setting should be Std. Bi-Direct . 11. Drives I/O This option displays the address and interrupt level for hard disk drive, CD/DVD- ROM drive and PC card. It is for [...]

3 Tests and Diagnostics 3.28 SETUP 3-92 Satellite Pro M10 Series Maintenance Manual (960-431) 14. Peripheral Use this option to select the parallel port mode and hard disk mode. (a) Internal Pointing Device This option enables and disables the Touch Pad and accupoint. Enabled Enables the Touch Pad and accupoint. (Default) Disabled Disables the Touc[...]

3.28 SETUP 3 Tests and Diagnostics Satellite Pro M10 Series Ma intenance Manual (960-431) 3-93 (c) Parallel Port Mode The options in this tab are ECP and Standard Bi-directional. ECP Sets the port mode to Extended Capabilities Port (ECP). For most printers, the port should be set to ECP. (Default) Std. Bi-Direct. This setting should be used with so[...]

3 Tests and Diagnostics 3.28 SETUP 3-94 Satellite Pro M10 Series Maintenance Manual (960-431) 16. PCI LAN This option enables/disables the Built-in LAN functions. (a) Built-in LAN Enabled Enables Built-in LAN functions. (Default) Disabled Disables Built-in LAN functions.[...]

Chapter 4 Replacement Procedures[...]

4 Replacement Procedures 4-ii Satellite Pro M10 Series Maintenance Manual (960-431)[...]

4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-iii Chapter 4 Contents 4.1 General .................................................................................................................... ... 4-1 Safety Precautions...........................................................................................[...]

4 Replacement Procedures 4-iv Satellite Pro M10 Series Maintenance Manual (960-431) 4.7 Keyboard .................................................................................................................. 4 -29 Removing the Keyboard .................................................................................... 4-29 Installing the Keybo[...]

4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-v Installing the Cooling Fan.................................................................................. 4-56 4.18 RTC Battery ............................................................................................................. 4- 57 Removing the RTC Bat[...]

4 Replacement Procedures 4-vi Satellite Pro M10 Series Maintenance Manual (960-431) Removing the TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) ........ 4-90 Installing the TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) .......... 4-96 4.29 TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) ........................................ 4-102 Removing the [...]

4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-vii Figures Figure 4-1 Removing the battery ..................................................................................... 4-8 Figure 4-2 Removing a PC Card ................................................................................... 4-10 Figure 4-3 Remov[...]

4 Replacement Procedures 4-viii Satellite Pro M10 Series Maintenance Manual (960-431) Figure 4-31 Removing the wireless LAN card ................................................................ 4-47 Figure 4-32 Removing the screws from the bottom of the computer .............................. 4-49 Figure 4-33 Disconnecting the cable ...............[...]

4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-ix Figure 4-63 Disconnecting the FL tube ground wire ...................................................... 4-87 Figure 4-64 Removing the FL tube ................................................................................. 4-88 Figure 4-65 Removing the outsi de ta[...]

4 Replacement Procedures 4-x Satellite Pro M10 Series Maintenance Manual ( 960-431) Figure 4-92 Removing the frame ................................................................................... 4-121 Figure 4-93 Removing the panel ................................................................................... 4-122 Figure 4-94 Removing the[...]

4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-xi Figure 4-124 Applying the protective cover-G ............................................................... 4-151 Figure 4-125 Applying the protective cover-S ................................................................ 4-152 Figure 4-126 Applying the tapes ...[...]

4 Replacement Procedures 4-xii Satellite Pro M10 Series Maintenance Manual (960-431)[...]

4.1 General 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-1 4 p 4.1 General This section explains how to disassemble the computer and replace Field Replaceable Units (FRUs). It may not be necessary to remove all the FRUs in order to replace one. The chart below is a guide to which FRUs need to be removed in order[...]

4 Replacement Procedures 4.1 General 4-2 Satellite Pro M10 Series Maintenance Manual (960-431) Safety Precautions Before you begin disassembly, read the following safety precautions and observe them carefully as you work. DANGER: 1. Always use the genuine battery that is authorized by TOSHIBA or compatible with the unit. Since other battery packs h[...]

4.1 General 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-3 Before You Begin Look over the procedures in this section before you begin disassembling the computer. Familiarize yourself with the disassembly and reassem bly steps. Begin each procedure by removing the AC adapter and the battery pack as instructed in [...]

4 Replacement Procedures 4.1 General 4-4 Satellite Pro M10 Series Maintenance Manual (960-431) Disassembly Procedures The computer has three basic types of cable connectors:  Pressure Plate Connectors  Coaxial Cable Connectors  Normal Pin Connectors To disconnect a Pressure Plate connector, lift up the tabs on either side of the connector?[...]

4.1 General 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-5 Tools and Equipment The use of Electrostatic Discharge (ESD) equipment is very important for your safety and the safety of those around you. Proper use of these devices will increase the success rate of your repairs and lower the cost for damaged or dest[...]

4 Replacement Procedures 4.1 General 4-6 Satellite Pro M10 Series Maintenance Manual (960-431) Screw Tightening Torque When you fasten screws, be sure to follow the torque list below. CAUTION: Overtightening can damage components and screws; undertightening can result in electrical shorts or other damage if screws or components come loose. NOTE: TO[...]

4.1 General 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-7 Color of Screw Shaft To avoid mistakes on the screw length, screw shafts are colored as follows: ❑ Even number length screw: brown ❑ Odd number length screw: white ❑ Special length screw: blue Screws whose lengths are indicated to one or more decim[...]

4 Replacement Procedures 4.1 General 4-8 Satellite Pro M10 Series Maintenance Manual (960-431) Removing the Battery Pack To remove the battery pack, follow the steps below and refer to Figure 4-1. CAUTION: When handling battery packs, be careful not to short circuit the terminals. Also do not drop, hit or otherwise apply impact; do not scratch or b[...]

4.1 General 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-9 Installing the Battery Pack To install the battery pack, follow the steps below and refer to Figure 4-1. CAUTION: The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery [...]

4 Replacement Procedures 4.1 General 4-10 Satellite Pro M10 Series Maintenance Manual (960-431) Removing an Optional PC Card To remove a PC Card (option), follow the steps below and refer to Figure 4-2. CAUTION: Before you remove a PC Card, refer to the card's documentation and to your operating system documentation for proper procedures and p[...]

4.1 General 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-11 Removing an Optional SD Card To remove an SD card (option), follow the steps below and refer to Figure 4-3. CAUTION: Before you remove an SD card, refer to the card's documentation and to your operating system documentation for proper procedures an[...]

4 Replacement Procedures 4.2 Memory Modules 4-12 Satellite Pro M10 Series Maintenance Manual (960-431) 4.2 Memory Modules Removing a Memory Module To remove a mem ory module make sure the com puter is in boot mode and powered off, follow the steps below and refer to Figures 4-4 and 4-5. CAUTION: Do not try to remove a memory module with the compute[...]

4.2 Memory Modules 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-13 4. Gently press out on two latches . One end of the memory module will pop up. 5. Grasp the memory module and pull it out. Latches Memor y module Figure 4-5 Removing the memory modules[...]

4 Replacement Procedures 4.2 Memory Modules 4-14 Satellite Pro M10 Series Maintenance Manual (960-431) Installing a Memory Module To install a memory m odule, make sure that the computer is in boot m ode and powered off, follow the steps below and refer to Figures 4-4 and 4-5. CAUTION: Do not touch the connectors on the memory module or on the comp[...]

4.3 HDD 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-15 4.3 HDD CAUTION : When handling the HDD, do not press the top surface as shown by the arrow. Hold it by the sides. Removing the HDD To remove the HDD, follow the steps below and refer to Figures 4-6 to 4-8. 1. Turn the computer upside down. 2. Remove two M2[...]

4 Replacement Procedures 4.3 HDD 4-16 Satellite Pro M10 Series Maintenance Manual (960-431) 4. Pull the HDD gently out of the slot. HDD Figure 4-7 Removing the HDD pack NOTE: The following steps describe how to disassemble the HDD pack; however, do not disassemble if the HDD is working properly.[...]

4.3 HDD 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-17 5. Place the HDD pack on a flat surface, and remove four M3 × 4 silver flat-head screws . 6. Remove the HDD bracket . M3 × 4 silver flat-head scre ws M3 × 4 silver flat-head scre ws HDD HDD brac ket Figure 4-8 Removing screws and HDD bracket CAUTION: Do [...]

4 Replacement Procedures 4.3 HDD 4-18 Satellite Pro M10 Series Maintenance Manual (960-431) Installing the HDD To install the HDD, follow the steps below and refer to Figures 4-6 to 4-8. CAUTION: Don't hold the HDD by its top and bottom flat surfaces. It may damage the HDD. 1. Seat the HDD in the bracket . 2. Secure the bracket with four M3 ×[...]

4.4 Slim Select Bay Module 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-19 4.4 Slim Select Bay Module Removing the Slim Select Bay Module To remove the slim select bay m odule, follow the steps below and refer to Figures 4-9 and 4- 10. 1. If a screw ( M3 × 4 black flat-head screw ) is set in the lock position, [...]

4 Replacement Procedures 4.4 Slim Select Bay Module 4-20 Satellite Pro M10 Series Maintenance Manual (960-431) NOTE: If you are going to replace an ODD, follow the steps below to disassemble the slim select bay module. 3. Remove two M2 × 8 black screw s securing the connector cover . 4. Remove the connector cover and ODD interface board . 5. Remov[...]

4.4 Slim Select Bay Module 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-21 Installing the Slim Select Bay Module To install the slim select bay module, follow the steps below and refer to Figures 4-9 and 4- 10. 1. Seat the ODD in the ODD bracket . 2. Secure the ODD bracket to the ODD with five M2 × 3 thin silve[...]

4 Replacement Procedures 4.5 Modem Daughter Card 4-22 Satellite Pro M10 Series Maintenance Manual (960-431) 4.5 Modem Daughter Card Removing the Modem Daughter Card To remove the modem daughter card (MDC), follow the steps below and refer to Figures 4- 11 and 4-12. 1. Remove one M2.5 × 6 black flat-head screw and tw o M2.5 × 4 black flat-head scr[...]

4.5 Modem Daughter Card 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-23 3. Remove two M2 × 4 screw s securing the MDC . 4. Carefully lift up the MDC to disconnect it from PJ2017 on the system board . 5. Carefully disconnect the modem cable from JP1 on the MDC . M2 × 4 screws MDC MDC's connector PJ2017 JP1[...]

4 Replacement Procedures 4.5 Modem Daughter Card 4-24 Satellite Pro M10 Series Maintenance Manual (960-431) Installing the Modem Daughter Card To install the modem daughter card (MDC), follow the steps below and refer to Figures 4-11 and 4-12. 1. Carefully connect the modem cable to JP1 on the MDC . 2. Seat the MDC and press carefully on the right [...]

4.6 CPU 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-25 4.6 CPU Removing the CPU To remove the CPU, follow the steps below and refer to Figures 4-13 and 4-16. 1. Remove one M2.5 × 6 black flat-head screw and tw o M2.5 × 4 black flat-head screw securing the CPU/MDC slot cover , if necessary. 2. Remove two M2 ×[...]

4 Replacement Procedures 4.6 CPU 4-26 Satellite Pro M10 Series Maintenance Manual (960-431) 3. Remove the cooling module . Cooling module Figure 4-14 Removing the cooling module 4. Turn the cam to the unlock position with a flat-blade screwdriver to unlock the CPU . LOCK OPEN Figure 4-15 Unlocking the CPU[...]

4.6 CPU 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-27 5. Lift up the CPU . CPU Figure 4-16 Removing the CPU[...]

4 Replacement Procedures 4.6 CPU 4-28 Satellite Pro M10 Series Maintenance Manual (960-431) Installing the CPU To install the CPU, follow the steps below and refer to Figures 4-13 to 4-17. 1. Make sure the cam is in the open position. 2. Seat the CPU in the CPU socket , aligning the triangle mark on the CPU with that on the socket. Make sure the al[...]

4.7 Keyboard 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-29 4.7 Keyboard Removing the Keyboard To remove the keyboard, follow the steps below and refer to Figures 4-18 to 4-21. 1. Open the display panel. 2. Insert your fingernails into notches in the keyboard brace and the computer, and pry up to unlatch the br[...]

4 Replacement Procedures 4.7 Keyboard 4-30 Satellite Pro M10 Series Maintenance Manual (960-431) 3. Remove two M2.5 × 2.6 black flat-head screw s securing the keyboard. 4. Rotate out the keyboard and lay it on top of the palm rest. M2.5 × 2.6 blac k flat-head screws K eyboard Figure 4-19 Removing screws securing the keyboard[...]

4.7 Keyboard 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-31 5. Remove one M2.5 × 16 black screw securing the metal plate to remove it. M2.5 × 16 blac k screws Metal plate Figure 4-20 Removing the metal plate[...]

4 Replacement Procedures 4.7 Keyboard 4-32 Satellite Pro M10 Series Maintenance Manual (960-431) 6. Disconnect the keyboard cable from PJ123 on the system board , and remove the keyboard . K eyboard K eyboard cab le PJ123 Figure 4-21 Removing the keyboard[...]

4.7 Keyboard 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-33 Installing the Keyboard To install the keyboard, follow the steps below and refer to Figures 4-18 to 4-21. 1. Lay the keyboard on the palm rest upside down. 2. Connect the keyboard cable to PJ123 on the system board . 3. Seat the metal plate and secure[...]

4 Replacement Procedures 4.8 Switch Board 4-34 Satellite Pro M10 Series Maintenance Manual (960-431) 4.8 Switch Board Removing the Switch Board To remove the switch board, make sure the com puter is in boot mode and powered off, follow the steps below and refer to Figure 4-22. 1. Disconnect the switch board cable from PJ2025 on the system board. 2.[...]

4.8 Switch Board 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-35 Installing the Switch Board To install the switch board, make sure that the computer is in boot m ode and powered off, follow the steps below and refer to Figure 4-22. 1. Seat the switch board . 2. Secure the switch board with two M2.5 × 3 black f[...]

4 Replacement Procedures 4.9 Speakers 4-36 Satellite Pro M10 Series Maintenance Manual (960-431) 4.9 Speakers Removing the Speakers To remove the speakers, follow the steps below and refer to Figures 4-23 and 4-24. 1. Turn the computer upside down. 2. Remove two M2.5 × 16 black screw s . M2.5 × 16 blac k screws Figure 4-23 Removing the screws sec[...]

4.9 Speakers 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-37 3. Remove one M2.5 × 4 black flat-head screw securing each speaker . 4. Disconnect two speaker cables from PJ5004 and PJ5005 on the system board . 5. Free two speaker cables from their hooks. 6. Remove one M2.5 × 4 black flat-head screw from each of [...]

4 Replacement Procedures 4.9 Speakers 4-38 Satellite Pro M10 Series Maintenance Manual (960-431) Installing the Speakers To install the speakers, follow the steps below and refer to Figures 4-23 and 4-24. 1. Seat each of the speaker and secure it from one latch. 2. Secure each of the speaker with one M2.5 × 4 black flat-head screw . 3. Route two s[...]

4.10 Palm Rest 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-39 4.10 Palm Rest Removing the Palm Rest To remove the palm rest, follow the steps below and refer to Figures 4-25 and 4-26. 1. Turn the computer upside down. 2. Remove seven M2.5 × 12 black screws . M2.5 × 12 blac k screws M2.5 × 12 blac k screws Fi[...]

4 Replacement Procedures 4.10 Palm Rest 4-40 Satellite Pro M10 Series Maintenance Manual (960-431) 3. Turn the computer right side up and open the display panel. 4. Disconnect the pad cable from PJ2003 on the system board . 5. Remove two M2.5 × 5 black flat-head screw s securing the palm rest . 6. Release two latches to remove the palm rest . M2.5[...]

4.10 Palm Rest 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-41 Installing the Palm Rest To install the palm rest, follow the steps below and refer to Figures 4-25 and 4-26. 1. Insert four tabs of the palm rest into the slits on the top cover to seat the palm rest . Secure the palm rest with two latches . 2. Secu[...]

4 Replacement Procedures 4.11 Touch Pad 4-42 Satellite Pro M10 Series Maintenance Manual (960-431) 4.11 Touch Pad Removing the Touch Pad To remove the touch pad, follow the steps below and refer to Figures 4-27 and 4-28. 1. Remove two M2.5 × 5 black flat-head screw s and two M2.5 × 4 screw s from the back of the palm rest . M2.5 × 5 blac k flat-[...]

4.11 Touch Pad 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-43 2. Hold the palm rest with both hands and then slightly bend it to release two latches securing each sides of the touch pad cover . Be careful not to bend the palm rest excessively, or it will be broken. 3. Remove the touch pad cover and touch pad . [...]

4 Replacement Procedures 4.12 Internal Microphone 4-44 Satellite Pro M10 Series Maintenance Manual (960-431) 4.12 Internal Microphone Removing the Internal Microphone To remove the internal microphone, follow the steps below and refer to Figure 4-29. 1. Remove one strip of tape securing the internal microphone cable . 2. Disconnect the internal mic[...]

4.13 Bluetooth Module 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-45 4.13 Bluetooth Module Removing the Bluetooth Module To remove the Bluetooth module, follow the steps below and refer to Figure 4-30. NOTE: The Bluetooth module is an option in some models. 1. Disconnect the Bluetooth antenna coaxial cable (bro[...]

4 Replacement Procedures 4.13 Bluetooth Module 4-46 Satellite Pro M10 Series Maintenance Manual (960-431) Installing the Bluetooth Module To install the Bluetooth module, make sure that the com puter is in boot mode and powered off, follow the steps below and refer to Figure 4-30. NOTE: The Bluetooth module is an option in some models. 1. Connect t[...]

4.14 Wireless LAN Mini PCI Card 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-47 4 s 4.14 Wireless LAN Mini PCI Card Removing the Wireless LAN Mini PCI Card To remove the wireless LAN Mini PCI card, make sure the com puter is in boot mode and powered off, follow the steps below and refer to Figure 4-31. 1. Remove[...]

4 Replacement Procedures 4.14 Wireless LAN Mini PCI Card 4-48 Satellite Pro M10 Series Maintenance Manual (960-431) Installing the Wireless LAN Mini PCI Card To install the wireless LAN Mini PCI card, follow the steps below and refer to Figure 4-31. 1. Fit the wireless LAN Mini PCI card ’s connector into the computer’s connectors and press it c[...]

4.15 Top Cover with Display Assembly 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-49 4.15 Top Cover with Display Assembly Removing the Top Cover with Display Assembly To remove the top cover with display assembly, follow the steps below and refer to Figures 4-32 to 4-35. 1. Turn the computer upside down. 2. Remo[...]

4 Replacement Procedures 4.15 Top Cover with Display Assembly 4-50 Satellite Pro M10 Series Maintenance Manual (960-431) 4. Turn the computer right side up and open the display panel. 5. Disconnect following two cables : • LCD/FL cable from PJ4205 on the VGA board • Internal microphone cable from PJ5002 on the sound board (if necessary) LCD/FL [...]

4.15 Top Cover with Display Assembly 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-51 6. Remove following screws from the top cover: • Three M2.5 × 5 black screws • One M2.5 × 4 brass flat-head screw • One M2.5 × 12 black flat-head screw M2.5 × 5 blac k screws M2.5 × 12 blac k flat-head screw M2.5 × 4[...]

4 Replacement Procedures 4.15 Top Cover with Display Assembly 4-52 Satellite Pro M10 Series Maintenance Manual (960-431) 7. Lift up the display assembly to release six latches securing the top cover with the bottom case, and then remove the top cover and display assembly . Latches T op cov er Displa y assembly Figure 4-35 Removing the top cover wit[...]

4.15 Top Cover with Display Assembly 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-53 Installing the Top Cover with Display Assembly To install the top cover with display assembly, follow the steps below and refer to Figures 4- 32 to 4-35. 1. Seat the top cover with display assembly and secure it with six latches[...]

4 Replacement Procedures 4.16 Sound Board 4-54 Satellite Pro M10 Series Maintenance Manual (960-431) 4.16 Sound Board Removing the Sound Board To remove the sound board, follow the steps below and refer to Figure 4-36. 1. Remove two M2.5 × 4 screw s securing the sound board . 2. Gently lift up the sound board to disconnect it from PJ5006 on the sy[...]

4.17 Cooling Fan 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-55 4.17 Cooling Fan Removing the Cooling Fan To remove the cooling fan, follow the steps below and refer to Figures 4-37. CAUTION: The cooling fan can become very hot during operation. Wait for the fan to cool before removing it. Do not touch the fan [...]

4 Replacement Procedures 4.17 Cooling Fan 4-56 Satellite Pro M10 Series Maintenance Manual (960-431) Installing the Cooling Fan To install the cooling fan, follow the steps below and refer to Figures 4-37. CAUTION: When you remove the cooling fan, wipe the grease off of the bottom of the heat sink and top of the CPU. Apply new grease. 1. Seat the c[...]

4.18 RTC Battery 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-57 4.18 RTC Battery WARNING: When it is necessary to replace the RTC battery, be sure to use genuine batteries or replacement batteries authorized by TOSHIBA. Installing the wrong battery could cause a battery explosion or other damage. If the RTC bat[...]

4 Replacement Procedures 4.18 RTC Battery 4-58 Satellite Pro M10 Series Maintenance Manual (960-431) Removing the RTC Battery To remove the RTC battery, follow the steps below and refer to Figure 4-38. 1. Remove two strips of tape securing the RTC battery cable . 2. Disconnect the RTC battery cable from PJ9999 on the system board . 3. Remove one st[...]

4.19 System Board 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-59 4.19 System Board Removing the System Board To remove the system board, follow the steps below and refer to Figures 4-39 to 4-41. 1. Lift the AC adaptor jack out of its slot. A C adaptor jack Figure 4-39 Dismounting the AC adaptor jack[...]

4 Replacement Procedures 4.19 System Board 4-60 Satellite Pro M10 Series Maintenance Manual (960-431) 2. Rotate the system board from the right side to lift it out of the bottom case . Be careful not to catch the bottom case on the eject buttons of the PC Card Slot. 3. Disconnect the AC adaptor jack from PJ8800 on the system board . System board PJ[...]

4.19 System Board 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-61 4. Remove two strips of tape securing the modem cable . 5. Disconnect the modem cable from PJ2018 on the system board . PJ2018 Modem cable T apes Figure 4-41 Removing the modem cable Installing the System Board To install the system board, follow [...]

4 Replacement Procedures 4.20 VGA Board 4-62 Satellite Pro M10 Series Maintenance Manual (960-431) 4.20 VGA Board Removing the VGA Board To remove the VGA board, follow the steps below and refer to Figure 4-42. 1. Remove three M2 × 4 screws securing the VGA board . 2. Gently lift up the VGA board to disconnect it from PJ100 on the system board . M[...]

4.21 USB Board 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-63 4.21 USB Board Removing the USB Board To remove the USB board, follow the steps below and refer to Figure 4-43. 1. Remove one M2 × 4 screw securing the USB board . 2. Remove the USB board . M2 × 4 screw USB board Figure 4-43 Removing the USB board [...]

4 Replacement Procedures 4.22 Display Mask 4-64 Satellite Pro M10 Series Maintenance Manual (960-431) 4 s 4.22 Display Mask Removing the Display Mask To remove the display mask, follow the steps below and refer to Figures 4-44 and 4-45. 1. Remove two mask seals at the bottom corners of the display assembly. 2. Remove two M2.5 × 6 black flat-head s[...]

4.22 Display Mask 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-65 3. Release the twenty-seven latches on the display mask in the following order: • Seven latches on the bottom • six latches each on the right and left sides • eight latches on the top. Latches Displa y mask Figure 4-45 Removing the display m[...]

4 Replacement Procedures 4.22 Display Mask 4-66 Satellite Pro M10 Series Maintenance Manual (960-431) Installing the Display Mask To install the display mask, follow the steps below and refer to Figures 4-44 and 4-45. 1. Place the display mask in position, and fasten the twenty-seven latches in the following order: • Eight latches on the top • [...]

4.23 FL Inverter Board 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-67 4.23 FL Inverter Board Removing the FL Inverter Board To remove the FL inverter board, follow the steps below and refer to Figures 4-46 and 4-47. 1. Remove one M2 × 4 flat-head screw securing the FL inverter board . 2. Turn over the insulato[...]

4 Replacement Procedures 4.23 FL Inverter Board 4-68 Satellite Pro M10 Series Maintenance Manual (960-431) 3. Rotate out the FL inverter board and disconnect the FL cable from CN1 on the FL inverter board . 4. Disconnect the HV cable from CN2 on the FL inverter board . 5. Remove the FL inverter board . FL inv erter board FL cable CN1 CN2 HV cable F[...]

4.23 FL Inverter Board 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-69 Installing the FL Inverter Board To install the FL inverter board, follow the steps below and refer to Figures 4-46 and 4-47. 1. Connect the FL inverter cable to CN1 and the HV cable to CN2 . 2. Seat the FL inverter board . 3. Secure the FL i[...]

4 Replacement Procedures 4.24 LCD Module 4-70 Satellite Pro M10 Series Maintenance Manual (960-431) 4.24 LCD Module NOTE: Be careful not to apply pressure to the ICs along the edge of LCD module. The ICs are easily damaged. NOTE: For environmental reasons, do not throw away a malfunctioning LCD module (or FL). Please follow local ordinances or regu[...]

4.24 LCD Module 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-71 3. Carefully rotate out the top of the LCD module to access the LCD/FL cable . 4. Remove the tape securing the LCD/FL cable . 5. Disconnect the LCD/FL cable . 6. Remove the LCD module . T ape LCD cable Connector LCD module Figure 4-49 Removing the L[...]

4 Replacement Procedures 4.24 LCD Module 4-72 Satellite Pro M10 Series Maintenance Manual (960-431) 7. Remove four silver super flat-head M2 × 3 screws securing two metal braces . M2 × 3 silver super flat-head scre ws M2 × 3 silver super flat-head scre ws Metal brace Figure 4-50 Removing the metal braces[...]

4.24 LCD Module 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-73 Installing the LCD Module To install the LCD module , follow the steps below and refer to Figures 4-48 to 4-50. 1. Seat two metal braces and secure each with two silver super flat-head M2 × 3 screws . 2. Connect the LCD/FL cable to the LCD module .[...]

4 Replacement Procedures 4.25 Antenna Coaxial Cables 4-74 Satellite Pro M10 Series Maintenance Manual (960-431) 4.25 Antenna Coaxial Cables Removing the Antenna Coaxial Cables To remove the antenna coaxial cables, follow the steps below and refer to Figures 4-51 to 4- 53. NOTE: When you open or close the top cover, hold it by the sides close to the[...]

4.25 Antenna Coaxial Cables 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-75 3. Turn over the insulator securing the antenna coaxial cables . 4. Remove a strip of tape covering the antenna coaxial cables . 5. Free the antenna coaxial cables from their groove . 6. Remove two M2.5 × 4 black flat-head screw s secur[...]

4 Replacement Procedures 4.25 Antenna Coaxial Cables 4-76 Satellite Pro M10 Series Maintenance Manual (960-431) 8. Turn the computer right side up and open the display panel. 9. Pull out the antenna coaxial cables from the hinge . 10. Remove four strips of tape securing the antenna coaxial cables . 11. Remove the antennas . Antenna T apes Antenna c[...]

4.25 Antenna Coaxial Cables 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-77 Installing the Antenna Coaxial Cables To install the antenna coaxial cables, follow th e steps below and refer to Figures 4-51 to 4-53. 1. Seat the antennas and route the antenna coaxial cables . 2. Secure the antenna coaxial cable with [...]

4 Replacement Procedures 4.26 LCD/FL Cable 4-78 Satellite Pro M10 Series Maintenance Manual (960-431) 4.26 LCD/FL Cable Removing the LCD/FL Cable To remove the LCD/FL cable and antenna coaxial cable, follow the steps below and refer to Figures 4-54 to 4-56. NOTE: When you open or close the top cover, hold it by the sides close to the hinges to prev[...]

4.26 LCD/FL Cable 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-79 3. Turn the computer right side up and open the display panel. 4. Remove one M2.5 × 6 tapping screw securing the metal brace . 5. Remove the metal brace . Metal brace M2.5 × 6 tapping screw Figure 4-55 Remove the metal brace[...]

4 Replacement Procedures 4.26 LCD/FL Cable 4-80 Satellite Pro M10 Series Maintenance Manual (960-431) 6. Close the display panel. 7. Remove the LCD/FL cable . LCD/FL cable Figure 4-56 Removing the LCD/FL cable Installing the LCD/FL Cable To install the LCD/FL cable, follow the steps below and refer to Figures 4-54 to 4-56. 1. Route the LCD/FL cable[...]

4.27 TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-81 4 4.27 TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) Removing the TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) To remove the TFT FL (Model 14.1 XGA Samsung LTN141XF-L02), follow the steps below and refer to Figures 4[...]

4 Replacement Procedures 4.27 TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) 4-82 Satellite Pro M10 Series Maintenance Manual (960-431) 2. Remove the two screws for fixing the power supply board. CAUTION: Use care not to damage the PCB. 1 2 Screw Scre w Figure 4-58 Removing the two screws for fixing the power supply board[...]

4.27 TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-83 3. Release the 18 hooks and remove the upper chassis from the fram e. There are six hooks at the top, four hooks on each of the left- and right-hand sides, and four hooks at the bottom. 1st 2nd 2nd 3rd T op Hook Sid[...]

4 Replacement Procedures 4.27 TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) 4-84 Satellite Pro M10 Series Maintenance Manual (960-431) 4. Remove the panel assembly from the backlight assembly. CAUTION: Use care not to damage the TCP during working. P anel assembly Backlight assemb ly Figure 4-60 Removing the panel assembly[...]

4.27 TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-85 5. Remove the two clips. 6. Remove these: • Prism sheet • Diffuser sheet • Light guide plate (LGP) • Reflective sheet Remov e the clip Remov e the clip Sheets Figure 4-61 Removing the panel assembly[...]

4 Replacement Procedures 4.27 TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) 4-86 Satellite Pro M10 Series Maintenance Manual (960-431) 7. Remove the two screws for fixing the back cover of the FL tube. Screws Figure 4-62 Removing the screws for fixing the FL tube back cover[...]

4.27 TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-87 8. Disconnect the ground wire of the FL tube from the frame. F rame GND wire Hot wire Figure 4-63 Disconnecting the FL tube ground wire[...]

4 Replacement Procedures 4.27 TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) 4-88 Satellite Pro M10 Series Maintenance Manual (960-431) 9. Remove the FL tube from the fram e. FL Figure 4-64 Removing the FL tube[...]

4.27 TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-89 Installing the TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) To install the TFT FL (Model 14.1 XGA Samsung LTN141XF-L02), follow the steps below and refer to Figures 4-57 to 4-65. 1. Place the FL tube on the correct [...]

4 Replacement Procedures 4.28 TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) 4-90 Satellite Pro M10 Series Maintenance Manual (960-431) 4.28 TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) Removing the TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) To remove the TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO), follow the steps below and refer[...]

4.28 TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-91 T ape Adhesive:7250L-0026U Cov er Shield (C):3550L-0281A Cov er Shield (G):7250L-0154B T ape Adhesive:7250L-0026N T ape Adhesive:7250L-0026K Figure 4-65 Removing the outside tape/cover tape[...]

4 Replacement Procedures 4.28 TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) 4-92 Satellite Pro M10 Series Maintenance Manual (960-431) Removing the control PCB, top case and cover assembly 6. Remove the FPC cable (1) used for the control PCB connecting. CAUTION : Pressure or stress should not be given on the FPC cable. 7. Remove the control PCB [...]

4.28 TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-93 Removing the source PCB and gate PCB 10. Remove the source PCB (1). CAUTION : Pressure or stress should not be given on the PCB and TCP during removing double tape. 11. Remove the gate PCB (2). CAUTION : Pressur[...]

4 Replacement Procedures 4.28 TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) 4-94 Satellite Pro M10 Series Maintenance Manual (960-431) Removing the board assembly, tape pad sheet, light guide, cover bottom and lamp assembly 12. Remove the board assembly (1). CAUTION : This process should be made in the clean room with no scratch nor particle on [...]

4.28 TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-95 Board Assembly:6060L-C017 Sheets & LGP Screw Scre w Double T ape:7250L-0025E T ape P ad Figure 4-68 Removing the board assembly, tape pad sheet, light guide, cover bottom and lamp assembly[...]

4 Replacement Procedures 4.28 TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) 4-96 Satellite Pro M10 Series Maintenance Manual (960-431) Installing the TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) To install the TFT FL (Model 14.1 LG. XGA Philips LP141X7-C1TO), follow the steps below and refer to figures 4-69 to 4-72. Attaching the double tape[...]

4.28 TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-97 Board Assembly:6060L-C017 Sheets and LGP Kapton T ape: 7250L-0026Q Screw Scre w Double T ape:7250L-0025E T ape P ad Figure 4-69 Attaching the double tape, lamp assembly , cover bottom, sheets, light guide, tape [...]

4 Replacement Procedures 4.28 TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) 4-98 Satellite Pro M10 Series Maintenance Manual (960-431) Attaching the source PCB and gate PCB 9. Attach the source PCB (1). CAUTION : Stress should not be given on the TCP. 10. Attach the gate PCB (2). CAUTION : Stress should not be given on the TCP. Source PCB Gate P[...]

4.28 TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-99 Attaching the cover bottom, screw, top case, control PCB and FPC 11. Attach the bottom cover and screw (1). CAUTION : Pressure should not be given on the source TCP. 12. Attach the top case (2). CAUTION : Pressu[...]

4 Replacement Procedures 4.28 TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) 4-100 Satellite Pro M10 Series Maintenance Manual (960-431) Attaching the outside tape and cover shield 15. Attach the tape adhesive (1) used for B/L wire fixing. CAUTION : Pressure or stress should not be given on the B/L wire fixing. 16. Attach the tape adhesive (2) us[...]

4.28 TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-101 T ape Adhesive:7250L-0026U Cov er Shield (C):3550L-0281A Cov er Shield (G):7250L-0154B T ape Adhesive:7250L-0026K T ape Adhesive:7250L-0026N T ape Adhesive:7250L-0050A Figure 4-72 Attaching the outside tape and[...]

4 Replacement Procedures 4.29 TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) 4-102 Satellite Pro M10 Series Maintenance Manual (960-431) 4 4.29 TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) Removing the TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) CAUTION: Exercise care during FL removal not to damage the LCD panel and not to let dust or other foreign[...]

4.29 TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-103 2. Remove two screw s securing the PCB. Screw Scre w Figure 4-74 Removing the screws securing the PCB 3. Remove four screws on the right and left sides of the chassis. Screws Scre ws Figure 4-75 Removing screws sec[...]

4 Replacement Procedures 4.29 TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) 4-104 Satellite Pro M10 Series Maintenance Manual (960-431) 4. Release eight hooks (four hooks on the bottom side first and four hooks on the right and left side) and remove the top chassis from the LCD m odule starting from the bottom end. CAUTION: When you release hooks on[...]

4.29 TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-105 5. Turn the LCD module face up and remove the panel assembly from the mold-frame . Handle with care not to damage COF . P anel assembly Mold-frame Figure 4-77 Removing the panel assembly[...]

4 Replacement Procedures 4.29 TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) 4-106 Satellite Pro M10 Series Maintenance Manual (960-431) 6. Remove two clips and six sheets (protector, prism (L,U), diffuser, LGP, and reflector sheet) from the back light assembly. Clip Clip Sheets Figure 4-78 Removing one screw, two clips, tape and six sheets[...]

4.29 TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-107 7. Turn the back light assembly face down and remove tw o screws to remove the lamp cover from the mold fram e. Screw Scre w Lamp cov er Figure 4-79 Removing the lamp cover[...]

4 Replacement Procedures 4.29 TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) 4-108 Satellite Pro M10 Series Maintenance Manual (960-431) 8. Free the HV cable from the mold-fram e’s cable guide. HV cable (GND) HV cable (HO T) Figure 4-80 Freeing the HV cable[...]

4.29 TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-109 9. Pull the FL assembly out of its groove on the mold frame. FL assembly Figure 4-81 Removing the FL assembly[...]

4 Replacement Procedures 4.29 TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) 4-110 Satellite Pro M10 Series Maintenance Manual (960-431) Installing the TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) To install the TFT FL (Model 15.0 XGA Samsung LTN150X6-L01), follow the steps below and refer to Figures 4-73 to 4-81. 1. Seat the FL in its groove on the [...]

4.30 TFT FL (Model 15.0 XGA LG. Philips LP150X06 A2) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-111 4.30 TFT FL (Model 15.0 XGA LG. Philips LP150X06 A2) CAUTION : When you replace the fluorescent lamp, wear finger covers or gloves to avoid contaminating or damaging the LCD panel. Be careful not to let dust or [...]

4 Replacement Procedures 4.30 TFT FL (Model 15.0 XGA LG. Philips LP150X06 A2) 4-112 Satellite Pro M10 Series Maintenance Manual (960-431) 5. Disassembly of Top Case. Pressure or stress should not be given on Top Case and Gate TCP. Figure 4-83 Disassembly of Top case[...]

4.30 TFT FL (Model 15.0 XGA LG. Philips LP150X06 A2) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-113 6. Disassembly of Source PCB. Pressure or stress should not be given on PCB and TCP during removing double tape. 7. Disassembly of Gate PCB. Pressure or stress should not be given on PCB and TCP during removing [...]

4 Replacement Procedures 4.30 TFT FL (Model 15.0 XGA LG. Philips LP150X06 A2) 4-114 Satellite Pro M10 Series Maintenance Manual (960-431) 8. Disassembly of Board Ass’y. This process should be made in Clean room with no scratch nor particle on Polarizer and B/L Ass’y. 9. Disassembly of Tape Adhesive used for Sheets fixing (4 Point). 10. Disassem[...]

4.30 TFT FL (Model 15.0 XGA LG. Philips LP150X06 A2) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-115 Installing the TFT FL (Model 15.0 XGA LG. Philips LP150X06 A2) To install the TFT FL (Model 15.0 LG. XGA Philips LP150X06 A2), follow the steps below and refer to Figures 4-86 to 4-89. 1. Detach a protect film f[...]

4 Replacement Procedures 4.30 TFT FL (Model 15.0 XGA LG. Philips LP150X06 A2) 4-116 Satellite Pro M10 Series Maintenance Manual (960-431) 6. Assembly of Source PCB. Stress should not be given on TCP 7. Assembly of Gate PCB. Stress should not be given on TCP Figure 4-87 Assembly of Source PCB and Gate PCB[...]

4.30 TFT FL (Model 15.0 XGA LG. Philips LP150X06 A2) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-117 8. Assembly of Top Case. Pressure should not be given on Source TCP. Figure 4-88 Assembly of Cover Ass’y and Top Case[...]

4 Replacement Procedures 4.30 TFT FL (Model 15.0 XGA LG. Philips LP150X06 A2) 4-118 Satellite Pro M10 Series Maintenance Manual (960-431) 9. Assembly of Tape shield and Tape Adhesive used for Top case fixing. Pressure or stress should not be given on Top case during this process 10. Assembly of Cover shield (C). Pressure or stress should not be giv[...]

4.31 TFT FL (Model 15.0 XGA Chi Mei N150X2-L01) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-119 4.31 TFT FL (Model 15.0 XGA Chi Mei N150X2-L01) Removing the TFT FL (Model 15.0 XGA Chi Mei N150X2-L01) To remove the TFT FL (Model 15.0 XGA Chi Mei N150X2-L01), follow the steps below and refer to figures 4-90 to 4-[...]

4 Replacement Procedures 4.31 TFT FL (Model 15.0 XGA Chi Mei N150X2-L01) 4-120 Satellite Pro M10 Series Maintenance Manual (960-431) 2. Remove two screws securing the X-PCB. 3. Remove eight screws securing the metal fram e. 4. Release a hook. Screw Screw Detail of the hook Screw Screw Screw Screw Screw Screw Screw Screw Metal frame Figure 4-91 Remo[...]

4.31 TFT FL (Model 15.0 XGA Chi Mei N150X2-L01) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-121 5. Push the latch out of lower frame from the lam p holder and then the latch on both sides. Be careful not to distort the frame. Backlight Metal frame Figure 4-92 Removing the frame[...]

4 Replacement Procedures 4.31 TFT FL (Model 15.0 XGA Chi Mei N150X2-L01) 4-122 Satellite Pro M10 Series Maintenance Manual (960-431) 6. Unfold the X-PCB. Be careful not to distort the TCP. 7. Turn the LCD module right side up. 8. Remove the panel. P anel Backlight unit Figure 4-93 Removing the panel[...]

4.31 TFT FL (Model 15.0 XGA Chi Mei N150X2-L01) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-123 9. Remove three spacers from the BEFIII-M sheet. 10. Remove the BEFIII-M sheet, BEFIII-T sheet, diffuser sheet, and two strips of tape. Be careful not to damage the sheets. Spacer BEFIII-M sheet BEMIII-T sheet Diffus[...]

4 Replacement Procedures 4.31 TFT FL (Model 15.0 XGA Chi Mei N150X2-L01) 4-124 Satellite Pro M10 Series Maintenance Manual (960-431) 11. Remove two screws securing the FL. 12. Remove the FL. Screw Screw FL Housing Figure 4-95 Removing the FL[...]

4.31 TFT FL (Model 15.0 XGA Chi Mei N150X2-L01) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-125 Installing the TFT FL (Model 15.0 XGA Chi Mei N150X2-L01) To install the TFT FL (Model 15.0 XGA Chi Mei N150X2-L01), follow the steps below and refer to Figures 4-90 to 4-95. 1. Seat the FL and secure it with two scr[...]

4 Replacement Procedures 4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) 4-126 Satellite Pro M10 Series Maintenance Manual (960-431) 4 4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) Removing the TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) CAUTION: Exercise care during FL removal not to damage the LCD panel and not to let dust or other f[...]

4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-127 2. Remove two screw s securing the PCB. Screw Scre w Figure 4-97 Removing the screws securing the PCB[...]

4 Replacement Procedures 4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) 4-128 Satellite Pro M10 Series Maintenance Manual (960-431) 3. Remove four screws on the right and left sides of the chassis. Screws Scre ws Figure 4-98 Removing screws securing the chassis[...]

4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-129 4. Release nine hooks (four hooks on the bottom side first and five hooks on the right and left side) and remove the top chassis from the LCD m odule starting from the bottom end. CAUTION: When you release hooks [...]

4 Replacement Procedures 4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) 4-130 Satellite Pro M10 Series Maintenance Manual (960-431) 5. Turn the LCD module face up and remove the panel assembly from the mold-frame . Handle with care not to damage COF P anel assembly Mold-frame Figure 4-100 Removing the panel assembly[...]

4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-131 6. Remove two clips and five sheets (prism (L,U), diffuser, LGP, and reflector sheet) from the back light assembly. Clip Clip Sheets Figure 4-101 Removing one screw, two clips, tape and six sheets[...]

4 Replacement Procedures 4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) 4-132 Satellite Pro M10 Series Maintenance Manual (960-431) 7. Turn the back light assembly face down and remove tw o screws to remove the lamp cover from the mold fram e. Screw Scre w Lamp cov er Figure 4-102 Removing the lamp cover[...]

4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-133 8. Free the HV cable from the mold-fram e’s cable guide. HV cable (GND) HV cable (HO T) Figure 4-103 Freeing the HV cable[...]

4 Replacement Procedures 4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) 4-134 Satellite Pro M10 Series Maintenance Manual (960-431) 9. Pull the FL assembly out of its groove on the mold frame. FL assembly Figure 4-104 Removing the FL assembly[...]

4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-135 Installing the TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) To install the TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03), follow the steps below and refer to Figures 4-96 to 4-104. 1. Seat the FL in its groove[...]

4 Replacement Procedures 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4-136 Satellite Pro M10 Series Maintenance Manual (960-431) 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) Removing the TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) To remove the TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43), follow the steps below and refer to Figures 4-105 t[...]

4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-137 3. Remove four screws from the side of the LCD m odule. Screw Scre w Screw Loosen the screws with 1.1kgf ⋅ cm of torque. Screw Figure 4-106 Removing the screws 4. Turn the LCD module right side up. 5. Remove the t[...]

4 Replacement Procedures 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4-138 Satellite Pro M10 Series Maintenance Manual (960-431) 6. Turn the LCD module upside down. 7. Remove four screws securing the PCBs. 8. Disconnect the FPC. 9. Fold out the PCBs. Open the connector cover and disconnect the connector. Loosen the screws with 0.9kgf ¥ cm of [...]

4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-139 10. Turn the LCD module right side up. 11. Remove the LCD panel from the backlight unit. W hen you remove the LCD panel, wear finger covers or gloves to avoid contaminating or damaging the LCD panel and the backligh[...]

4 Replacement Procedures 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4-140 Satellite Pro M10 Series Maintenance Manual (960-431) 12. Turn the backlight unit upside down taking care not to damage or contaminate the sheets. 13. Remove two screws securing the lamp cover to rem ove it. Screw Screw Loosen the screws with 1.1kgf ¥ cm of torque. Lam[...]

4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-141 14. Turn the backlight unit right side up. 15. Remove the upper diffuser sheet, lens sheet, and light guide sheet. Be careful not to damage or contaminate the sheets because they are reused. Lens sheet Upper diffuse[...]

4 Replacement Procedures 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4-142 Satellite Pro M10 Series Maintenance Manual (960-431) 17. Turn the backlight unit upside down. 18. Gentry remove the FL taking care not to damage it. P-chassis FL Figure 4-113 Removing the FL NOTE : Be careful not to fold the reflective sheet back when you remove the FL[...]

4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-143 Installing the TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) To install the TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43), follow the steps below and refer to Figures 4-114 to 4-126. 1. Apply four strips of double-faced[...]

4 Replacement Procedures 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4-144 Satellite Pro M10 Series Maintenance Manual (960-431) 2. Install a new FL unit into the frame. Frame FL Cross section of Z—Z Install the FL into the frame making sure it does not stick out from the frame. Let the reflective sheet inside the reflector Fit the wire firm[...]

4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-145 3. Seat the lamp cover on the backlight unit and secure it with two screws. Tighten the screws with 0.9kgf•cm of torque. Screw Screw Lamp cover Figure 4-116 Installing the lamp cover 4. Install the light guide she[...]

4 Replacement Procedures 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4-146 Satellite Pro M10 Series Maintenance Manual (960-431) 5. Strip all of the liner on the double-faced tape applied to the frame. 6. Lay the lens sheet and upper diffuser sheet on the backlight unit. Be careful not to contaminate or damage any sheets. Lens sheet Upper diff[...]

4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-147 7. Seat the LCD panel on the backlight unit assembled by the steps above. Make sure there are no dust between the LCD panel and the backlight. If you find any foreign matter, remove it. 8. Make sure the LCD panel fi[...]

4 Replacement Procedures 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4-148 Satellite Pro M10 Series Maintenance Manual (960-431) 9. Fold the TCP of the source PCB down. 10. Secure the source PCB with two screws. 11. Fold the TCP of the gate PCB down. 12. Secure the gate PCB with two screws. Do not grasp both ends. Do not grasp both ends. TCP o[...]

4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-149 13. Connect the FPC to the connector on the source PCB. Make sure the latch secures the connector correctly. See the notches on both the edge of the FPC, and see the contour of the connector. Insert the FPC into the[...]

4 Replacement Procedures 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4-150 Satellite Pro M10 Series Maintenance Manual (960-431) 14. Install the top frame. Secure the top frame and the lam p cover with six latches. <Side view> Top frame Hook the U-shaped side of the top frame to the P-chassis. Lay the top frame on the lamp cover. Be sure[...]

4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-151 15. Secure four screws on the side of the module. Screw Scre w Screw Tighten the screws with 0.9kgf ⋅ cm of torque. Screw Figure 4-123 Securing the screws 16. Apply the protective cover-G. Protective co v er-G Ali[...]

4 Replacement Procedures 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4-152 Satellite Pro M10 Series Maintenance Manual (960-431) 17. Apply the protective cover-S. Align the cov er's edge with the edge of the plastic par t of the connector Make sure that the amount of displacement is ± 0.5 mm or less . Apply the cov er's edge close t[...]

4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-153 18. Apply the fixing tape and the HV cable fixing tape. Secure the cable with tape. Be sure the cable lies flat. Apply the fixing tape around the center of the module. 0 to 1 mm Be sure not to let the tape protrude [...]

4 Replacement Procedures 4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 4-154 Satellite Pro M10 Series Maintenance Manual (960-431) 4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) CAUTION : When you replace the fluorescent lamp, wear finger covers or gloves to avoid contaminating or damaging the LCD panel. Be careful not to let dust or other forei[...]

4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-155 3. Remove five screws from the side of the LCD module. Loosen the screws with 1.0 kgf•com of torque. Screw Screw Screw Screw Screw Figure 4-128 Removing the screws 4. Turn the LCD module right side up. 5. Remove th[...]

4 Replacement Procedures 4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 4-156 Satellite Pro M10 Series Maintenance Manual (960-431) 6. Turn the LCD module upside down. 7. Remove five screws securing the PCBs. 8. Disconnect the FPC . FPC Open the connector cover and disconnect the connector. Loosen the screws with 1.0kgf ¥ cm of torque. Screw Scre[...]

4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-157 10. Turn the LCD module right side up. 11. Remove the LCD panel from the backlight unit . When you rem ove the LCD panel , wear finger covers or gloves to avoid staining or damaging the LCD panel and the backlight un[...]

4 Replacement Procedures 4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 4-158 Satellite Pro M10 Series Maintenance Manual (960-431) 14. Turn the backlight unit right side up. 15. Remove three strips of shield tape , the optical sheet , the upper lens sheet , the lower lens sheet , the lower diffuser sheet and the light guide sheet . Be careful not[...]

4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-159 Installing the TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) To install the TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13), follow the steps below and refer to Figures 4-136 to 4-147. 1. Install a new FL unit into the frame[...]

4 Replacement Procedures 4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 4-160 Satellite Pro M10 Series Maintenance Manual (960-431) 2. Seat the lamp cover on the backlight unit and secure it with two screws . V W Lamp cover Tighten the screws with 1.0kgf•cm of torque. Detail of W Detail of V Backlight unit Screw Screw Align the holes on the lamp[...]

4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-161 4. Lay the lower diffuser sheet , the lower lens sheet , the upper lens sheet and the optical sheet on the backlight unit . Be careful not to stain or damage any sheets. X Y X Y 0‘ 1 0‘ 1 1 Shield tape Shield tap[...]

4 Replacement Procedures 4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 4-162 Satellite Pro M10 Series Maintenance Manual (960-431) 5. Seat the LCD panel on the backlight unit assembled by the steps above. Make sure there is no dust between the LCD panel and the backlight unit . If you find any foreign matter, remove it. Guide rib Make sure the LC[...]

4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-163 7. Secure the TCP of the source PCB with three screws . 8. Secure the TCP of the gate PCB with two screws . 9. Connect the FPC to the connector on the source PCB. Screw Screw Pin * Pin * Screw Screw Screw Tighten the[...]

4 Replacement Procedures 4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 4-164 Satellite Pro M10 Series Maintenance Manual (960-431) 10. Install the top frame . Top frame Hook the U-shaped side of the top frame to the P-chassis. <Side view> Lay the top frame on the lamp cover. Be sure the top frame does not interfere with the TCP. Figure 4-14[...]

4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 4 Replacement Procedures Satellite Pro M10 Series Ma intenance Manual (960-431) 4-165 12. Secure five M2 × 2 screws on the side of the module. Screw Screw Screw Screw Screw Tighten the screws with 1.0 kgf•cm of torque. Figure 4-145 Securing the screws 13. Apply the protective cover-G . Protective c[...]

4 Replacement Procedures 4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 4-166 Satellite Pro M10 Series Maintenance Manual (960-431) 14. Apply the protective cover-S , the aluminum tape and the wire-protective tape . 0 ‘ 0.5m m 0 ‘ 1mm 0 ‘ 1mm 0 ‘ 1mm Protective cover-S Aluminum sheet Aluminum tape Wire-protective tape Align the holes on th[...]

Appendices[...]

Appendices App-ii Satellite Pro M10 Series Maintenance Manual (960-431)[...]

Appendices Satellite Pro M10 Series Main tenance Manual (960-431) App-iii Appendix Contents Appendix A Handling the LCD Module .......................................................................... A-1 Appendix B Board Layout .................................................................................................B-1 B.1 System Board (F[...]

Appendices App-iv Satellite Pro M10 Seri es Maintenance Manual (960-431) C.19 PJ4015 Video Out I/F Connector (2-pin) ...........................................................C-23 C.20 PJ4900 Bluetooth I/F Connector (20-pin) ..........................................................C-24 C.21 PJ5004 Right Speaker I/F Connector (2-pin) .............[...]

Appendices Satellite Pro M10 Series Main tenance Manual (960-431) App-v Appendix D Keyboard Scan/Character Codes................................................................ D-1 Appendix E Key Layout .....................................................................................................E-1 E.1 United States (US) Keyboard ..........[...]

Appendices App-vi Satellite Pro M10 Seri es Maintenance Manual (960-431) Figures Figure B-1 System board (FQDSY*) layout (front) ........................................................B-1 Figure B-2 System board (FQDSY*) layout (back).........................................................B-4 Figure B-3 VGA board (FQDVG*) layout (front) .........[...]

Appendices Satellite Pro M10 Series Main tenance Manual (960-431) App-vii Tables Table B-1 System board (FQDSY*) layout (front) ........................................................B-2 Table B-2 System board (FQDSY*) layout (back) .........................................................B-5 Table B-3 VGA board (FQDVG*) layout (front) ...........[...]

Appendices App-viii Satellite Pro M10 Seri es Maintenance Manual (960-431) Table C-23 Sound board (FQDSD*) I/F conn ector pin assignments (60-pin) ...............C-25 Table C-24 IEEE 1394 I/F connector pin assignments (4-pin).......................................C-26 Table C-25 Cooling fan I/F connector pin assignments (3-pin) ....................[...]

Appendix A Handling the LCD Module Satellite Pro M10 Series Ma intenance Manual (960-431) A-1 Appendix A Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged during assem bly or disassembly. Observe the following precautions when handling the LCD module: 1. When installing the LCD module in[...]

Appendix A Handling the LCD Module A-2 Satellite Pro M10 Series Maintenance Manual (960-431) 3. If the panel’s surface gets dirty, wipe it with cotton or a soft cloth. If it is still dirty, try breathing on the surface to create a light condensate and wipe it again. If the surface is very dirty, we recommend a CRT cleaning agent. Apply the agent [...]

Appendix A Handling the LCD Module Satellite Pro M10 Series Maintenance Manual (960-431) A-3 5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks. 6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a wrist or a[...]

Appendix A Handling the LCD Module A-4 Satellite Pro M10 Series Maintenance Manual (960-431) 7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage.[...]

Appendix A Handling the LCD Module Satellite Pro M10 Series Maintenance Manual (960-431) A-5 9. Do not disassemble the LCD module. Disassem bly can cause malfunctions. 10. If you transport the module, do not use packing material that contains epoxy resin (amine) or silicon glue (alcohol or oxime). These m aterials can release gas that can damage th[...]

Appendix A Handling the LCD Module A-6 Satellite Pro M10 Series Maintenance Manual (960-431)[...]

Appendix B Board Layout Appendices Satellite Pro M10 Series Ma intenance Manual (960-431) B-1 Appendix B Board Layout B.1 System Board (FQDSY*) Front View Figure B-1 System board (FQDSY*) layout (front)[...]

Appendices Appendix B Board Layout B-2 Satellite Pro M10 Series Maintenance Manual (960-431) Table B-1 System board (FQDSY*) layout (front) (1/2) Mark Number Nam e (A) PJ123 Keyboard I/F Connector (B) PJ326 Debug Port I/F Connector (C) PJ2003 Touch Pad I/F Connector (D) PJ2015 Mini PCI Card I/F Connector (E) PJ2025 Switch Board (FQDSQ*) I/F Connect[...]

Appendix B Board Layout Appendices Satellite Pro M10 Series Ma intenance Manual (960-431) B-3 Table B-1 System board (FQDSY*) layout (front) (2/2) Mark Number Name (AA) DS2004 Battery LED (Green) (AB) DS2005 Battery LED (Orange) (AC) DS2006 HDD LED (AD) DS2008 Slim Select Bay (Green) (AE) DS2009 Slim Select Bay (Orange) (AF) DS2010 Wireless Communi[...]

Appendices Appendix B Board Layout B-4 Satellite Pro M10 Series Maintenance Manual (960-431) B.2 System Board (FQDSY*) Back View Figure B-2 System board (FQDSY*) layout (back)[...]

Appendix B Board Layout Appendices Satellite Pro M10 Series Ma intenance Manual (960-431) B-5 Table B-2 System board (FQDSY*) layout (back) (1/1) Mark Number Nam e (A) PJ100 VGA Board (FQDVG*) I/F Connector (B) PJ117 TOSHIBA Style Bay I/F Connector (C) PJ124 RJ-45 & RJ-11 I/F Connector (D) PJ1001 SO-DIMM Socket Connector 0 (E) PJ1002 SO-DIMM So[...]

Appendices Appendix B Board Layout B-6 Satellite Pro M10 Series Maintenance Manual (960-431) Table B-2 System board (FQDSY*) layout (back) (2/2) Mark Number Name (AA) F8810 Fuse for Battery (10A) (AB) F8820 Fuse for Slim Select Bay (10A) (AC) S2302 Wireless Communication Switch (AD) X2002 Clock for Super I/O (14.31818MHz) (AE) X4500 Clock for 82562[...]

Appendix B Board Layout Appendices Satellite Pro M10 Series Ma intenance Manual (960-431) B-7 B.3 VGA Board (FQDVG*) Front View Figure B-3 VGA board (FQDVG*) layout (front) Table B-3 VGA board (FQDVG*) layout (front) Mark Number Name (A) PJ4205 LCD I/F Connector (B) PJ5500 System Board (FQDSY*) I/F Connector (C) IC3005 VRAM DDR SDRAM 128Mbit (4Mx32[...]

Appendices Appendix B Board Layout B-8 Satellite Pro M10 Series Maintenance Manual (960-431) B.4 VGA Board (FQDVG*) Back View Figure B-4 VGA board (FQDVG*) layout (back) Table B-4 VGA board (FQDVG*) layout (back) Mark Number Name (A) IC3002 VGAC GeForce4 420Go (B) IC3004 VRAM DDR SDRAM 128Mbit (4Mx32) (C) F4001 Fuse for LCD (3.15A) (D) X3000 Clock [...]

Appendix B Board Layout Appendices Satellite Pro M10 Series Ma intenance Manual (960-431) B-9 B.5 Sound Board (FQDSD*) Front View Figure B-5 Sound board (FQDSD*) layout (front) Table B-5 Sound board (FQDSD*) layout (front) Mark Number Name (A) PJ5002 Internal Microphone I/F Connector[...]

Appendices Appendix B Board Layout B-10 Satellite Pro M10 Series Maintenance Manual (960-431) B.6 Sound Board (FQDSD*) Back View Figure B-6 Sound board (FQDSD*) layout (back) Table B-6 Sound board (FQDSD*) layout (back) Mark Number Name (A) PJ5000 External Microphone I/F Connector (B) PJ5003 Headphone I/F Connector (C) PJ5007 System Board (FQDSY*) [...]

Appendix B Board Layout Appendices Satellite Pro M10 Series Ma intenance Manual (960-431) B-11 B.7 USB Board (FQDUB*) Back View Figure B-7 USB board (FQDUB*) layout (back) Table B-7 USB board (FQDUB*) layout (back) Mark Number Name (A) PJ2033 USB I/F Connector (B) PJ2042 System Board (FQDSY*) I/F Connector (C) IC2020 USB Current-Limited Switch MAX1[...]

Appendices Appendix B Board Layout B-12 Satellite Pro M10 Series Maintenance Manual (960-431)[...]

Apx.C Pin Assignments Appendices Satellite Pro M10 Series Ma intenance Manual (960-431) C-1 Appendix C Appendix C Pin Assignments System Board (FQDSY*) C.1 PJ100 VGA Board (FQD VG*) I/F Connector (200-pin) Table C-1 VGA board (FQDVG*) I/F connector pin assignments (200-pin) (1/3) Pin No. Signal name I/O Pin No. Signal name I/O 1 GND - 2 GND - 3 GND[...]

Appendices Apx.C Pin Assignments C-2 Satellite Pro M10 Series Maintenance Manual (960-431) Table C-1 VGA board (FQDVG*) I/F connector pin assignments (200-pin) (2/3) Pin No. Signal name I/O Pin No. Signal name I/O 63 PNL2-P3P I 64 PIRQG-P3N I 65 GND - 66 PNL0-P3P I 67 PNL1-P3P I 68 STPAGP-S3N O 69 RSTVGA-B3N O 70 PDNVGA-B3N O 71 GND - 72 GND - 73 G[...]

Apx.C Pin Assignments Appendices Satellite Pro M10 Series Ma intenance Manual (960-431) C-3 Table C-1 VGA board (FQDVG*) I/F connector pin assignments (200-pin) (3/3) Pin No. Signal name I/O Pin No. Signal name I/O 137 NC - 138 AV-PXP I 139 NC - 140 GND - 141 CRTBLU-PXP I 142 GND - 143 CRTGRN-PXP I 144 GND - 145 CRTRED-PXP I 146 GND - 147 DBLUE-PXP[...]

Appendices Apx.C Pin Assignments C-4 Satellite Pro M10 Series Maintenance Manual (960-431) C.2 PJ117 Slim Select Bay I/F Connector (72-pin) Table C-2 Slim Select Bay I/F connector pin assignments (72-pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 GND - 2 GND - 3 CDAUDR-EXP O 4 CDAUDL-EXP O 5 GND - 6 CD-GND - 7 IDRSTB-E5N O 8 GND - 9 GND - 1[...]

Apx.C Pin Assignments Appendices Satellite Pro M10 Series Ma intenance Manual (960-431) C-5 C.3 PJ123 Keyboard I/F Connector (34-pin) Table C-3 Keyboard I/F connector pin assignments (34-pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 NUMLED-P5N I 2 ARWLED-P5N I 3 CAPLED-P5N I 4 P5V O 5 KBSC00-S3N O 6 KBSC01-S3N O 7 KBSC02-S3N O 8 KBSC03-S3N[...]

Appendices Apx.C Pin Assignments C-6 Satellite Pro M10 Series Maintenance Manual (960-431) C.6 PJ1001 SO-DIMM Socket Connector 0 (200-pin) Table C-6 SO-DIMM socket connector 0 pin assignments (200-pin) (1/3) Pin No. Signal name I/O Pin No. Signal name I/O 1 MR1R25-P1V O 2 MR1R25-P1V O 3 GND - 4 GND - 5 SDQ00R-B2P I/O 6 SDQ06R-B2P I/O 7 SDQ04R-B2P I[...]

Apx.C Pin Assignments Appendices Satellite Pro M10 Series Ma intenance Manual (960-431) C-7 Table C-6 SO-DIMM socket connector 0 pin assignments (200-pin) (2/3) Pin No. Signal name I/O Pin No. Signal name I/O 63 GND - 64 GND - 65 SDQ26R-B2P I/O 66 SDQ30R-B2P I/O 67 SDQ27R-B2P I/O 68 SDQ31R-B2P I/O 69 2R5-B2V O 70 2R5-B2V O 71 SCB5A-B2P I/O 72 SCB0A[...]

Appendices Apx.C Pin Assignments C-8 Satellite Pro M10 Series Maintenance Manual (960-431) Table C-6 SO-DIMM socket connector 0 pin assignments (200-pin) (3/3) Pin No. Signal name I/O Pin No. Signal name I/O 137 GND - 138 GND - 139 SDQ38R-B2P I/O 140 SDQ35R-B2P I/O 141 SDQ44R-B2P I/O 142 SDQ41R-B2P I/O 143 2R5-B2V O 144 2R5-B2V O 145 SDQ45R-B2P I/O[...]

Apx.C Pin Assignments Appendices Satellite Pro M10 Series Ma intenance Manual (960-431) C-9 C.7 PJ1002 SO-DIMM Socket Connector 1 (200-pin) Table C-7 SO-DIMM socket connector 1 pin assignments (200-pin) (1/3) Pin No. Signal name I/O Pin No. Signal name I/O 1 MR1R25-P1V O 2 MR1R25-P1V O 3 GND - 4 GND - 5 SDQ00R-B2P I/O 6 SDQ06R-B2P I/O 7 SDQ04R-B2P [...]

Appendices Apx.C Pin Assignments C-10 Satellite Pro M10 Series Maintenance Manual (960-431) Table C-7 SO-DIMM socket connector 1 pin assignments (200-pin) (2/3) Pin No. Signal name I/O Pin No. Signal name I/O 63 GND - 64 GND - 65 SDQ26R-B2P I/O 66 SDQ30R-B2P I/O 67 SDQ27R-B2P I/O 68 SDQ31R-B2P I/O 69 2R5-B2V O 70 2R5-B2V O 71 SCB5B-B2P I/O 72 SCB0B[...]

Apx.C Pin Assignments Appendices Satellite Pro M10 Series Ma intenance Manual (960-431) C-11 Table C-7 SO-DIMM socket connector 1 pin assignments (200-pin) (3/3) Pin No. Signal name I/O Pin No. Signal name I/O 137 GND - 138 GND - 139 SDQ38R-B2P I/O 140 SDQ35R-B2P I/O 141 SDQ44R-B2P I/O 142 SDQ41R-B2P I/O 143 2R5-B2V O 144 2R5-B2V O 145 SDQ45R-B2P I[...]

Appendices Apx.C Pin Assignments C-12 Satellite Pro M10 Series Maintenance Manual (960-431) C.8 PJ1016 RGB I/F Connector (15-pin) Table C-8 RGB interface connector pin assignments (15-pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 CRTRED-PXP O 2 CRTGRN-PXP O 3 CRTBLU-PXP O 4 NC - 5 GND - 6 GND - 7 GND - 8 GND - 9 P5V O 10 GND - 11 NC - 12 D[...]

Apx.C Pin Assignments Appendices Satellite Pro M10 Series Ma intenance Manual (960-431) C-13 C.10 PJ1512 PC Card I/F Connector (150-pin) Table C-10 PC Card I/F connector pin assignments (150-pin) (1/2) Pin No. Signal name I/O Pin No. Signal name I/O 1 GND - 2 GND - 3 BCCD1-B3N I 4 BCAD00-BYP I/O 5 BCAD02-BYP I/O 6 BCAD01-BYP I/O 7 BCAD04-BYP I/O 8 [...]

Appendices Apx.C Pin Assignments C-14 Satellite Pro M10 Series Maintenance Manual (960-431) Table C-10 PC Card I/F connector pin assignments (150-pin) (2/2) Pin No. Signal name I/O Pin No. Signal name I/O 77 GND - 78 ACCD1-B3N I 79 ACAD00-BYP I/O 80 ACAD02-BYP I/O 81 ACAD01-BYP I/O 82 ACAD04-BYP I/O 83 ACAD03-BYP I/O 84 GND - 85 ACAD06-BYP I/O 86 A[...]

Apx.C Pin Assignments Appendices Satellite Pro M10 Series Ma intenance Manual (960-431) C-15 C.11 PJ2003 Touch Pad I/F Connector (8-pin) Table C-11 Touch Pad I/F connector pin assignments (8-pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 P5V O 2 IPDDAT-P5P 3 IPDCLK-P5P 4 GND - 5 SP-GND 6 SPY-PXP 7 SPX-PXP 8 SP-P5V C.12 PJ2007 Docking I/F Co[...]

Appendices Apx.C Pin Assignments C-16 Satellite Pro M10 Series Maintenance Manual (960-431) Table C-12 Docking I/F connector pin assignments (242-pin) (2/4) Pin No. Signal name I/O Pin No. Signal name I/O 53 GND - 54 NC - 55 NC - 56 NC - 57 NC - 58 NC - 59 MDMRNG-B3P I/O 60 MDMTIP-B3P I/O 61 DCOUT - 62 DCOUT - 63 EJCTRQ-S3N I/O 64 IF-P5V - 65 MOUSD[...]

Apx.C Pin Assignments Appendices Satellite Pro M10 Series Ma intenance Manual (960-431) C-17 Table C-12 Docking I/F connector pin assignments (242-pin) (3/4) Pin No. Signal name I/O Pin No. Signal name I/O 127 GND - 128 DTPB-B3P I/O 129 UBON1D-E5N O 130 UBOC1D-S3N O 131 GND - 132 UBON2D-E5N O 133 UBOC2D-S3N O 134 SNDMUT-S3N O 135 NC - 136 DOUTL-PXP[...]

Appendices Apx.C Pin Assignments C-18 Satellite Pro M10 Series Maintenance Manual (960-431) Table C-12 Docking I/F connector pin assignments (242-pin) (4/4) Pin No. Signal name I/O Pin No. Signal name I/O 201 RTS-PYP O 202 CTS-PYP I 203 DTR-PYP O 204 SELCT-P5P I 205 BUSY-P5P I 206 ACK-P5N I 207 PDB05-P5P I/O 208 GND - 209 GND - 210 PDB03-P5P I/O 21[...]

Apx.C Pin Assignments Appendices Satellite Pro M10 Series Ma intenance Manual (960-431) C-19 C.13 PJ2015 Mini PCI Card I/F Connector (124-pin) Table C-13 Mini PCI card I/F connector pin assignments (124-pin) (1/2) Pin No. Signal name I/O Pin No. Signal name I/O 1 NC - 2 NC - 3 NC - 4 NC - 5 NC - 6 NC - 7 NC - 8 NC - 9 NC - 10 NC - 11 NC - 12 NC - 1[...]

Appendices Apx.C Pin Assignments C-20 Satellite Pro M10 Series Maintenance Manual (960-431) Table C-13 Mini PCI I/F card connector pin assignments (124-pin) (2/2) Pin No. Signal name I/O Pin No. Signal name I/O 73 CBE1-P3N I 74 GND - 75 AD14-P3P I 76 AD15-P3P O 77 GND - 78 AD13-P3P O 79 AD12-P3P I 80 AD11-P3P O 81 AD10-P3P I 82 GND - 83 GND - 84 AD[...]

Apx.C Pin Assignments Appendices Satellite Pro M10 Series Ma intenance Manual (960-431) C-21 C.14 PJ2017 MDC I/F Connector (30-pin) Table C-14 MDC I/F connector pin assignments (30-pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 NC - 2 GND - 3 GND - 4 PHONE-BXN O 5 NC - 6 NC - 7 NC - 8 GND - 9 NC - 10 NC - 11 NC - 12 NC - 13 NC - 14 NC - 15 [...]

Appendices Apx.C Pin Assignments C-22 Satellite Pro M10 Series Maintenance Manual (960-431) C.16 PJ2020 Parallel I/F Connector (25-pin) Table C-16 Parallel I/F connector pin assignments (25-pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 STROB-P5N I 2 PDB00-P5P I/O 3 PDB01-P5P I/O 4 PDB02-P5P I/O 5 PDB03-P5P I/O 6 PDB04-P5P I/O 7 PDB05-P5P I[...]

Apx.C Pin Assignments Appendices Satellite Pro M10 Series Ma intenance Manual (960-431) C-23 C.18 PJ2040 USB Board (FQDUB*) I/F Connector (30-pin) Table C-18 USB Board (FQDUB*) I/F connector pin assignments (30-pin) Pin No. Signal name I/O Pin No Signal Name I/O 1 E5V O 2 E5V O 3 E5V O 4 E5V O 5 E5V O 6 E5V O 7 E5V O 8 E5V O 9 NC - 10 USBOC1-E3N I [...]

Appendices Apx.C Pin Assignments C-24 Satellite Pro M10 Series Maintenance Manual (960-431) C.20 PJ4900 Bluetooth I/F Connector (20-pin) Table C-20 Bluetooth I/F connector pin assignments (20-pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 BT-P3V O 2 NC - 3 NC - 4 USBP5-S3N I/O 5 USBP5-S3P I/O 6 NC - 7 NC - 8 -BTIFOF-S3N O 9 NC - 10 GND - 11[...]

Apx.C Pin Assignments Appendices Satellite Pro M10 Series Ma intenance Manual (960-431) C-25 C.23 PJ5006 Sound Board (FQD SD*) I/F Connector (60-pin) Table C-23 Sound board (FQDSD*) I/F connector pin assignments (60-pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 CDAUDL-EXP O 2 CD-GND - 3 CDAUDR-EXP O 4 CD-GND - 5 DINL-PXN O 6 DINL-PXP O 7 D[...]

Appendices Apx.C Pin Assignments C-26 Satellite Pro M10 Series Maintenance Manual (960-431) C.24 PJ6100 IEEE 1394 I/F Connector (4-pin) Table C-24 IEEE 1394 I/F connector pin assignments (4-pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 TPB0-P3N I/O 2 TPB0-P3P I/O 3 TPA0-P3N I/O 4 TPA0-P3P I/O C.25 PJ8770 Cooling fan I/F Connector (3-pin) T[...]

Apx.C Pin Assignments Appendices Satellite Pro M10 Series Ma intenance Manual (960-431) C-27 C.27 PJ8810 Battery I/F Connector (10-pin) Table C-27 Battery I/F connector pin assignments (10-pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 + 2 BTMP1 3 DCHG 4 M5V 5 PSCL-S5P 6 PSDA-S5P 7 GND - 8 DBT10V-S5N 9 GND - 10 GND - C.28 PJ9999 RTC Battery[...]

Appendices Apx.C Pin Assignments C-28 Satellite Pro M10 Series Maintenance Manual (960-431) VGA Board (FQDVG*) C.30 PJ4205 LCD I/F Connector (40-pin) Table C-30 LCD I/F connector pin assignments (40-pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 GND - 2 GND - 3 GND - 4 GND - 5 TXDT6-P3P O 6 GND - 7 TXDT6-P3N O 8 BRT2DA-S3P O 9 TXDT5-P3P O 1[...]

Apx.C Pin Assignments Appendices Satellite Pro M10 Series Ma intenance Manual (960-431) C-29 C.31 PJ5500 System Board (FQDSY*) I/F Connector (200-pin) Table C-31 System board (FQDSY*) I/F c onnector pin assignments (200-pin) (1/3) Pin No. Signal name I/O Pin No. Signal name I/O 1 GND - 2 GND - 3 GND - 4 AGAD00-PQP I/O 5 AGAD01-PQP I/O 6 GND - 7 AGA[...]

Appendices Apx.C Pin Assignments C-30 Satellite Pro M10 Series Maintenance Manual (960-431) Table C-31 System board (FQDSY*) I/F c onnector pin assignments (200-pin) (2/3) Pin No. Signal name I/O Pin No. Signal name I/O 63 PNL2-P3P O 64 PIRQG-P3N O 65 GND - 66 PNL0-P3P O 67 PNL1-P3P O 68 STPAGP-B3N I 69 RSTVGA-B3N I 70 PDNVGA-B3N I 71 GND - 72 GND [...]

Apx.C Pin Assignments Appendices Satellite Pro M10 Series Ma intenance Manual (960-431) C-31 Table C-31 System board (FQDSY*) I/F c onnector pin assignments (200-pin) (3/3) Pin No. Signal name I/O Pin No. Signal name I/O 137 NC - 138 AV-PXP O 139 NC - 140 GND - 141 CRTBLU-PXP O 142 GND - 143 CRTGRN-PXP O 144 GND - 145 CRTRED-PXP O 146 GND - 147 DBL[...]

Appendices Apx.C Pin Assignments C-32 Satellite Pro M10 Series Maintenance Manual (960-431) Sound Board (FQDSD*) C.32 PJ5000 External Microphone I/F Connector (6-pin) Table C-32 External microphone I/F connector pin assignments (6-pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 A-GND - 2 EMIC-PXP I 3 25VREF-P2V O 4 A-GND - 5 -EMICSL-P5P I 6 [...]

Apx.C Pin Assignments Appendices Satellite Pro M10 Series Ma intenance Manual (960-431) C-33 C.35 PJ5007 System Board (FQDSY*) I/F Connector (60-pin) Table C-35 System board (FQDSY*) I/F connector pin assignments (60-pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 CDAUDL-EXP I 2 CD-GND - 3 CDAUDR-EXP I 4 CD-GND - 5 DINL-PXN I 6 DINL-PXP I 7 [...]

Appendices Apx.C Pin Assignments C-34 Satellite Pro M10 Series Maintenance Manual (960-431) USB Board (FQDUB*) C.36 PJ2033 USB I/F Connector (8-pin) Table C-36 USB I/F connector pin assignments (8-pin) Pin No. Signal name I/O Pin No. Signal name I/O A1 USB0PS-E5V - A2 USBP0-S3N I/O A3 USBP0-S3P I/O A4 GND - B1 USB0PS-E5V - B2 USBP1-S3N I/O B3 USBP1[...]

Appendix D Keyboard Scan/Character Codes Satellite Pro M10 Series Maintenance Manual (960-431) D-1 Appendix D Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 01 ‘ ~ 29 A9 0E F0 0E 02 1 ! 02 82 16 F0 16 03 2 @ 03 83 1E F0 1E 04 3 # 04 84 26 F0 26 [...]

Appendix D Keyboard Scan/Character Codes D-2 Satellite Pro M10 Series Maintenance Manual (960-431) Table D-1 Scan codes (set 1 and set 2) (2/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 29 | 2B AB 5D F0 5D *5 30 Caps Lock 3A BA 58 F0 58 31 A 1E 9E 1C F0 1C 32 S 1F 9F 1B F0 1B 33 D 20 A0 23 F0 23 34 F 21 A1 2B F0 2B 35 G 22 A[...]

Appendix D Keyboard Scan/Character Codes Satellite Pro M10 Series Maintenance Manual (960-431) D-3 Table D-1 Scan codes (set 1 and set 2) (3/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 58 Ctrl 1D 9D 14 F0 14 *3 60 Alt (L) 38 B8 11 F0 11 *3 61 Space 39 B9 29 F0 29 62 ALT (R) E0 38 E0 B8 E0 11 E0 F0 11 75 Ins E0 52 E0 D2 E0 70 [...]

Appendix D Keyboard Scan/Character Codes D-4 Satellite Pro M10 Series Maintenance Manual (960-431) Table D-1 Scan codes (set 1 and set 2) (4/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 122 F11 57 D7 78 F0 78 *3 123 F12 58 D8 07 F0 07 *3 124 PrintSc *6 *6 *6 *6 *6 126 Pause *7 *7 *7 *7 *7 202 Fn — — — — *4 203 Win E0 5[...]

Appendix D Keyboard Scan/Character Codes Satellite Pro M10 Series Maintenance Manual (960-431) D-5 Table D-2 Scan codes with left Shift key Code set 1 Code set 2 Cap No. Key top Make Break Make Break 55 / E0 AA E0 35 E0 B5 E0 2A E0 F0 12 E0 4A E0 F0 4A E0 12 75 INS E0 AA E0 52 E0 D2 E0 2A E0 F0 12 E0 70 E0 F0 70 E0 12 76 DEL E0 AA E0 53 E0 D3 E0 2A[...]

Appendix D Keyboard Scan/Character Codes D-6 Satellite Pro M10 Series Maintenance Manual (960-431) Table D-3 Scan codes in Numlock mode Code set 1 Code set 2 Cap No. Key top Make Break Make Break 75 INS E0 2A E0 52 E0 D2 E0 AA E0 12 E0 70 E0 F0 70 E0 F0 12 76 DEL E0 2A E0 53 E0 D3 E0 AA E0 12 E0 71 E0 F0 71 E0 F0 12 79 ← E0 2A E0 4B E0 CB E0 AA E[...]

Appendix D Keyboard Scan/Character Codes Satellite Pro M10 Series Maintenance Manual (960-431) D-7 Table D-5 Scan codes in overlay mode Code set 1 Code set 2 Cap No. Keytop Make Break Make Break 09 8 (8) 48 C8 75 F0 75 10 9 (9) 49 C9 7D F0 7D 11 0 (*) 37 B7 7C F0 7C 23 U (4) 4B CB 6B F0 6B 24 I (5) 4C CC 73 F0 73 25 O (6) 4D CD 74 F0 74 26 P (–) [...]

Appendix D Keyboard Scan/Character Codes D-8 Satellite Pro M10 Series Maintenance Manual (960-431) Table D-7 No.126 key scan code Code set 1 Code set 2 Key top Shift Make Make Pause Co mm o n * E1 1D 45 E1 9D C5 E1 14 77 E1 F0 14 F0 77 Ctrl* E0 46 E0 C6 E0 7E E0 F0 7E *: This key generates only make codes.[...]

Appendix E Key Layout Satellite Pro M10 Series Maintenance Manual (960-431) E-1 Appendix E Appendix E Key Layout E.1 United States (US) Keyboard Figure E-1 US keyboard E.2 United Kingdom (UK) Keyboard Figure E-2 UK keyboard[...]

Appendix E Key Layout E-2 Satellite Pro M10 Series Maintenance Manual (960-431) E.3 German (GR) Keyboard Figure E-3 GR keyboard E.4 French (FR) Keyboard Figure E-4 FR keyboard[...]

Appendix E Key Layout Satellite Pro M10 Series Ma intenance Manual (960-431) E-3 E.5 Spanish (SP) Keyboard Figure E-5 SP keyboard E.6 Italian (IT) Keyboard Figure E-6 IT keyboard[...]

Appendix E Key Layout E-4 Satellite Pro M10 Series Maintenance Manual (960-431) E.7 Scandinavian (SC) Keyboard Figure E-7 SC keyboard E.8 Swiss-German (SL) Keyboard Figure E-8 SL keyboard[...]

Appendix E Key Layout Satellite Pro M10 Series Ma intenance Manual (960-431) E-5 E.9 Canadian (CS) Keyboard Figure E-9 CS keyboard[...]

Appendix E Key Layout E-6 Satellite Pro M10 Series Maintenance Manual (960-431)[...]

Appendix F Wiring Diagrams Satellite Pro M10 Series Maintenance Manual (960-431) F-1 Appendix F Appendix F Wiring Diagrams F.1 Parallel Port Wraparound Connector Figure F-1 Parallel port wraparound connector F.2 Serial Port Wraparound Connector Figure F-2 Serial port wraparound connector[...]

Appendix F Wiring Diagrams F-2 Satellite Pro M10 Series Maintenance Manual (960-431) F.3 Serial Port Direct Cable (9-Pin to 9-Pin) Figure F-3 Serial port direct cable (9-pin to 9-pin) F.4 Serial Port Direct Cable (9-Pin to 25-Pin) Figure F-4 Serial port direct cable (9-pin to 25-pin)[...]

Appendix G BIOS Rewrite Procedures Satellite Pro M10 Series Maintenance Manual (960-431) G-1 Appendix G Appendix G BIOS Rewrite Procedures This Appendix explains how to rewrite the system BIOS program when you update the system BIOS. Tools To rewrite the BIOS, you need the following tool:  BIOS/EC/KBC rewriting disk for the com puter that has re[...]

Appendix G BIOS Rewrite Procedures G-2 Satellite Pro M10 Series Maintenance Manual (960-431)[...]

Appendix H EC/KBC Rewrite Procedures Satellite Pro M10 Series Maintenance Manual (960-431) H-1 Appendix H Appendix H EC/KBC Rewrite Procedures This Appendix explains how to rewrite the EC/KBC system program when you update the EC/KBC system. Tools To rewrite the EC/KBC, you need the following tool:  BIOS/EC/KBC rewriting disk for the computer Re[...]

Appendix H EC/KBC Rewrite Procedures H-2 Satellite Pro M10 Series Maintenance Manual (960-431)[...]

Appendix I Reliability Satellite Pro M10 Series Maintenance Manual (960-431) I-1 Appendix I Appendix I Reliability The following table shows MTBF (Mean Time Between Failures) for each component. Table I-1 MTBF Component Time (hours) LCD 50,000 Keyboard 40,000 HDD 300,030 FDD 43,800 CD-RW/DVD drive 59,317 AC adaptor 50,000[...]

Appendix I Reliability I-2 Satellite Pro M10 Series Maintenance Manual (960-431)[...]