Rosewill RNWB-11001 manual

300M Wireless N Router RNX-N300R T User Manual 1910020437[...]

300M Wireless N Router RNX-N300RT User Manual COPYRIGHT & TRADEMARKS Specifications are subjec t to change without notice. is a registered trademark of Rosewill Inc. Other brands and product nam es are trademarks or registered trademarks of their respective holders. No part of the specific ations may be reproduced in any form or by any means or[...]

300M Wireless N Router RNX-N300RT User Manual FCC RF Radiation Exposure Statement This equipment complies with FCC RF radi ation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter . “T o comply with FCC RF exposure complian[...]

300M Wireless N Router RNX-N300RT User Manual Industry Canada statement: This device complies with RSS-210 of the Indus try Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interf erence, and (2) this dev ice must accept any interference received, including interfer ence that may cause und es[...]

300M Wireless N Router RNX-N300RT User Manual • Do not install, use, or service this device during a thunderstorm. There is a remote risk of electric shock from lightning. • Connect ONLY suitable accessories to the device. • Do not open the device or unit. Opening or removing covers can expose you to dangerous high voltage points or other ris[...]

300M Wireless N Router RNX-N300RT User Manual Contents Package Content s .................................................................................................................... 8 Chapter 1 Introduction ............................................................................................................ 9 1.1 Overview of the Wire[...]

300M Wireless N Router RNX-N300RT User Manual 4.7 DHCP Se tup .................................................................................................................. 64 4.7.1 DHCP Settings .............................................................................................. 64 4.7.2 DHCP Clients List ............................[...]

300M Wireless N Router RNX-N300RT User Manual 4.15.6 Reboot ....................................................................................................... 107 4.15.7 Password ................................................................................................... 108 4.15.8 System log ............................................[...]

300M Wireless N Router RNX-N300RT User Manual Package Contents The following items should be found in your package: • RNX-N300RT 300M Wireless N Router • Power Adapter for RNX-N300RT 300M Wireless N Router • Quick Installation Guide • Resource CD for RNX-N300RT 300M Wireless N Router including: ¾ This Guide ¾ Other Helpful Information ) N[...]

300M Wireless N Router RNX-N300RT User Manual Chapter 1 Introduction Congratulations on your pur chase of Rosewill’ s RNX-N300RT Wireless N Router . RNX-N300R T 300M Wire less N Router integrate s 4-port Switch, Firewall, NA T -Router and Wireless AP . Powered by 2x2 MIMO technol ogy , the 300M Wireless N Router delivers exceptional range and spe[...]

300M Wireless N Router RNX-N300RT User Manual ¾ One 10/100M Auto-Nego tiation RJ45 W A N por t, four 10/100M Auto-Negotiation RJ4 5 LAN ports, supporting Auto MDI/MDIX. ¾ Provides WP A/WP A2, WP A-PSK/WP A2-PSK authentication, TKIP /AES encryption security . ¾ Shares data and Internet access for user s, supporting Dynamic IP/S tatic IP/PPPoE Int[...]

300M Wireless N Router RNX-N300RT User Manual 1.3 Panel Layout 1.3.1 The Front Panel Figure 1-1 Front Panel sketch The Router’s LEDs and the WPS/Reset button are located on t he front panel (View from left to right). -1 1-[...]

300M Wireless N Router RNX-N300RT User Manual Name Statu s Indication Off Power is off. Power On Power is on. On The Router is initializing. Flashing The Router is working properly . System Off The Router has a system error . Off The Wireless function is disabled. WLAN Flashing The Wireless function is enabled. Off There is no device linked to the [...]

300M Wireless N Router RNX-N300RT User Manual 1.3.2 The Rear Panel Figure 1-2 Rear Panel sketch The following parts are lo cated on the rear panel (V iew from left to right). ¾ POWER: The Power socket is where you w ill connect the power adapter . Please use the power adapter provided with this RNX-N300RT 300M Wireless N Router. ¾ ON/OFF: The swi[...]

300M Wireless N Router RNX-N300RT User Manual Chapter 2 Connecting the Router 2.1 System Requirement s ¾ Broadband Internet Access Service (DSL/Cable/Ethernet) ¾ One DSL/Cable Modem that has an RJ45 connector (which is not necessary if the Router is connected dire ctly to the Ethernet.) ¾ PCs with a working Ethernet Adapter and an Ethernet cable[...]

300M Wireless N Router RNX-N300RT User Manual 5. Connect the DSL/Cable Modem to the W AN port on the Router , shown in Figure 2- 1 . 6. Connect the power adapter to the power socket on the Router , a nd the other end into an electrical outlet. The Router w ill st art to work automatically . 7. Power on your PC and Cable/DSL Modem. F i g u r e 2 - 1[...]

300M Wireless N Router RNX-N300RT User Manual Chapter 3 Quick Installation Guide This chapter will show you how to configure the basic functions of your R NX - N 3 0 0R T using Quick Setup Wiz ar d within minutes. 3.1 TCP/IP Configuration The default IP address of the RNX-N300R T is 192.168.1.1. And the default Subnet Mask is 255.255.255.0. Thes e [...]

300M Wireless N Router RNX-N300RT User Manual Figure 3-1 Success result of Ping command ¾ If the result displayed is similar to the Figure 3-2 , it means the connection between your PC and the Router is failed. Figure 3-2 Failure result of Ping command -17-[...]

300M Wireless N Router RNX-N300RT User Manual Please check the connection following these step s: 1. Is the connection bet ween your PC and the Router correct? ) Note: The 1/2/3/4 LEDs of LAN ports which you link to on the Router and LEDs on your PC's adapter should be lit. 2. Is the TCP/IP configur ation for your PC correct? ) Note: If the Ro[...]

300M Wireless N Router RNX-N300RT User Manual Step 3. Click on Quick Setup Step 4. Cli ck Next when sees this window -19-[...]

300M Wireless N Router RNX-N300RT User Manual Step 5. Click Auto-Det ect in this window as RNX-N300RT will detect and select for you connection option. Step 6. Entering your connection information in the next step. Y ou will need to verify with your ISP . PPPoE : Dynamic IP : Y ou do not need to enter anything i n this option. St atic IP : -20-[...]

300M Wireless N Router RNX-N300RT User Manual Step 7. Y ou will need to set up your wireless signal in this step. Step 8. Click Finish and you are ready! -21-[...]

300M Wireless N Router RNX-N300RT User Manual 3.2.2 Quick Inst allation Guide – Det ail and Explanation: 1. T o access the configuration utility , open a web-browser and type in the default address http://192.1 68.1.1 in the address field of the browser . Figure 3-3 Log in the Router After a moment, a login window will a ppear , similar to the Fi[...]

300M Wireless N Router RNX-N300RT User Manual Figure 3-5 Quick Setup 3. Click Next , and then WAN Connection Type page will appear, shown in Figure 3-6 . Figure 3-6 WAN Connection Type The Router provides Auto-Detect function and supports three popular ways PPPoE , Dyn am ic I P and Static IP to connect to the Internet. It’s recommended that you [...]

300M Wireless N Router RNX-N300RT User Manual Figure 3-7 Quick Setup - PPPoE ¾ User Name / Password - Enter the User Name and Password provided by your ISP. These fields are case s ensitive. If you have difficult y with this process, please contact your ISP. 2) If the connection type det ected is Dynamic IP , t he next screen will appear as shown [...]

300M Wireless N Router RNX-N300RT User Manual 5. Click Next to continue, the Wireless setti ngs p age will appear as shown in Figure 3-9 . Figure 3-9 Quick Setup – Wireless ¾ Wireless Radio - Enable or disable the wirele ss radio choosing from the pull-down list. ¾ SSID - Enter a value of up to 32 characters . The same name of SSID (Service Set[...]

300M Wireless N Router RNX-N300RT User Manual automatically. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point. ¾ Mode - This field determines the wireless mode which the Router works on. ¾ Channel Width - Select any channel width from the pull-down list. The default settin[...]

300M Wireless N Router RNX-N300RT User Manual Figure 3-10 Quick Setup - Finish If there are something changed on the Wireless page, you will see the Finish page as shown in Figure 3-1 1 . Click the Reboot button to make your wireless configuration to take ef fect and finish the Quick Setup . Figure 3-1 1 Quick Setup - Finish -27-[...]

300M Wireless N Router RNX-N300RT User Manual Chapter 4 Configuring the Router This chapter will show each Web p age's ke y functions and the c onfiguration way . 4.1 Functions Page After your successful login, you will see the fourteen main functi ons on the left of the Web-based utility . On the right side, th ere will the corresponding Setu[...]

300M Wireless N Router RNX-N300RT User Manual Figure 4-2 Router S tatus 4.3 Quick Setup Please refer to Section 3.2: "Quick Installation Guide." -29-[...]

300M Wireless N Router RNX-N300RT User Manual 4.4 WPS Setup This section will guide you to add a new wire less device to an existing network quickly by using the WPS (Wifi Protect Setup) function. a) Choose menu “ WPS ”, you will see the next screen (shown in Figure 4-3 ). Figure 4-3 WPS ¾ WPS St atus - Enable or disable the WPS function here.[...]

300M Wireless N Router RNX-N300RT User Manual ¾ Add device - Y ou can add a new device to the exis ting network manually by clicking this button. b) To add a new device: If the wireless adapter supports Wi-Fi Prot ected Setup (WPS), you can est ablish a wireless connection between wireless adapter and Router using either Push Button Configuration [...]

300M Wireless N Router RNX-N300RT User Manual The WPS Configuration Screen of Wireless Adapter Method T w o: Step 1: Press the WPS button on the front panel of the Router . Step 2: For the confi guration of the wirele ss adapter , please choose “ Push the button on my access point ” in the configuration utility of t he WPS as below , and click [...]

300M Wireless N Router RNX-N300RT User Manual The WPS Configuration Screen of Wireless Adapter Step 3: W ait for a while until the next screen appears. Click Finish to complete the WPS configuration. The WPS Configuration Screen of Wireless Adapter -33-[...]

300M Wireless N Router RNX-N300RT User Manual Method Three: Step 1: Keep the defaul t WPS Status as Enabled and click the Add device button in Figure 4-3 , then the following screen will appear. Figure 4-4 Add A New Device Step 2: Choose “ Pr ess the button of the new device in two minutes ” and click Connect . Step 3: For the configur ation of[...]

300M Wireless N Router RNX-N300RT User Manual Step 4: W ait for a while until the next screen appears. Click Finish to complete the WPS configuration. The WPS Configuration Screen of Wireless Adapter 4.4.2 By PIN If the new device supports Wi-Fi Protected Setup and the PIN method, you can add it to the network by PIN with the following two methods.[...]

300M Wireless N Router RNX-N300RT User Manual Step 2: Choose “ Ent er the new device's PIN ” and enter the PIN code of the wireless adapter in the field after PIN as shown in the figure above. Then click Connect. ) Note: The PIN code of the adapter is always displayed on the WPS configuration screen Step 3: For the configur ation of the wi[...]

300M Wireless N Router RNX-N300RT User Manual The WPS Configuration Screen of Wireless Adapter ) Note: The default PIN code of the R outer can be foun d in its label or the WPS configuration screen as Figure 4-3 . c) Y ou will see the following screen when t he new device successfully connected to the network. ) Note: 1) The WPS LED on the Router w[...]

300M Wireless N Router RNX-N300RT User Manual 2) The WPS function cannot be configured if the Wireless F unction of the Router is disabled. Please make sure the Wireless Function is enabled before config uring the WPS. 4.5 Network Figure 4-5 Network menu There are three submenus under the Network menu (shown in Figure 4-5 ): LAN , WA N and MAC Clon[...]

300M Wireless N Router RNX-N300RT User Manual ) Note: 1) If you change the IP Address of LAN, you mu st use the new IP Address to log in the Router . 2) If the new LAN IP Address you set is not in the same subnet, the IP Address pool of the DHCP server will change accordingly at the same time ， while the V irtual Server and DMZ Host will not take[...]

300M Wireless N Router RNX-N300RT User Manual including IP address, Subnet Mask, Default Gateway , etc. Click the Renew button to renew the IP p arameters from your ISP . Click the Release button to release the IP parameters. ¾ MTU Size - The normal MTU (Maximum T ransmission Unit ) value for most Ethernet networks is 1500 Bytes. It is not re comm[...]

300M Wireless N Router RNX-N300RT User Manual Figure 4-8 W AN - S tatic IP ¾ IP Address - Enter the IP address in dotted-decimal not ation provided by your ISP . ¾ Subnet Mask - Enter the subnet Mask in dotted- decimal notation provided by your ISP , usually is 255.255.25 5.0. ¾ Default Gateway - (Optional) Enter the gateway IP address in dotted[...]

300M Wireless N Router RNX-N300RT User Manual Figure 4-9 WAN - PP PoE ¾ User Name/Passw ord - Enter the User Name and Password provided by your ISP . These fields are case-sensitive. ¾ Secondary Connection - It’ s available only for PPPoE Connection. If your ISP provides an extra Connection type such as Dynamic/S tatic IP to connect to a local [...]

300M Wireless N Router RNX-N300RT User Manual the number of minutes you want to hav e elapsed before your Internet access disconnects. ¾ Connect Automatically - The connection can be re-estab lished automatically when it was down. ¾ Time-based Connecting - The connection will only be est ablish ed in the period from the start time to the end time[...]

300M Wireless N Router RNX-N300RT User Manual Figure 4-10 PPPoE Advanced Settings ¾ MTU Size - The default MTU size is “1480” bytes, which is usually fine. It is not recommended that you change the default MTU Size unless required by your ISP . ¾ Service Name/AC Name - The service name and AC (Access Concentrator) name should not be configure[...]

300M Wireless N Router RNX-N300RT User Manual 4. If your ISP provides BigPond Cable (or H eart Beat Signal) connection, please select BigPond Cable . And you should enter the following parameters ( Figure 4-1 1 ): Figure 4-1 1 WAN ¾ User Name/Passwo rd - Enter the User Name and Passw ord provided by your ISP . These fields are case-sensitive. ¾ A[...]

300M Wireless N Router RNX-N300RT User Manual ¾ Connect on Demand - In this mode, the Internet connection can be terminated automatically after a spec ified inactivity period ( Max Idle Time ) and be re-est ablished when you attempt to access the Internet again. If you want your Internet connection keeps active all the time , please enter “0” [...]

300M Wireless N Router RNX-N300RT User Manual Figure 4-12 W AN ¾ User Name/Passw ord - Enter the User Name and Password provided by your ISP . These fields are case-sensitive. ¾ Dynamic IP/ S t atic IP - Choose either as you are gi ven by your ISP . Click the Connect button to connect immediately . Click the Disconnect button to disconnect immedi[...]

300M Wireless N Router RNX-N300RT User Manual access the Internet again. If you wish to activate Connect on Demand , check the radio button. If you want your Internet connection to remain ac tive at all times, enter 0 in the Max Idle Time field. Otherwise, enter the number of minutes you want to have elapsed before your Inter net connection termina[...]

300M Wireless N Router RNX-N300RT User Manual Figure 4-13 PPTP Settings ¾ User Name/Passwo rd - Enter the User Name and Passw ord provided by your ISP . These fields are case-sensitive. ¾ Dynamic IP/ S t atic IP - Choose either as you are gi ven by your ISP and enter the ISP’s IP address or the domain name. If you choose static IP and enter the[...]

300M Wireless N Router RNX-N300RT User Manual ¾ Connect on Demand - Y ou can configure the Router to disconnect from your Internet connection after a specified period of inactivity ( Max Idle T i me ). If your Internet connection has been terminated due to inactivity , Connect on Demand enables the Router to automatically re-establish your connect[...]

300M Wireless N Router RNX-N300RT User Manual z Static IP - Connections which use stat ic IP address assignment. The Router can not detect PPT P/L2TP/BigPond connections with your ISP. If your ISP uses one of these protocol s, then you must configur e your connection manually. 4.5.3 MAC Clone Choose menu “ Network → MAC Clone ”, you can confi[...]

300M Wireless N Router RNX-N300RT User Manual 4.6 Wireless Figure 4-15 Wireless menu There are five submenus under the Wireless menu (shown in Figure 4-15 ): Wireless Settings , Wireless Security , Wireless MAC Filtering, Wireless Advanced and Wireless S t atistics. Click any of them, and you will be able to configure the corresponding function. 4.[...]

300M Wireless N Router RNX-N300RT User Manual Figure 4-16 Wireless Settings ¾ SSID - Enter a value of up to 32 characters . The same name of SSID (Service Set Identification) must be assigned to all wire less devices in your network. Considering your wireless network security, the def ault SSID is set to b e Rosewill_XXXXXX (XXXXXX indicates the l[...]

300M Wireless N Router RNX-N300RT User Manual Note Dialog ) Note: Limited by local law regulations, version fo r North America does not have re gion selection option. ¾ Channel - This field determines which operati ng frequency will be used. The default channel is set to Auto. so the AP will choose the best channel automatically. It is not necessa[...]

300M Wireless N Router RNX-N300RT User Manual ¾ Enable Wireless Router Radio - The wireless radio of this Router can be enabled or disabled to allow wireless stations access. ¾ Enable SSID Broadcast - When wireless clients survey the local area for wireless networks to associate with, they will detect the SSID broadcast by the Router. If you sele[...]

300M Wireless N Router RNX-N300RT User Manual ¾ WEP Index - This option should be chosen if the key type is WEP(ASCII) or WEP(HEX).It indicates the index of the WEP key. ¾ Auth Type - This option should be chosen if the key type is WEP(ASCII) or WEP(HEX).It indicates the authorization type of the Root AP. ¾ Password - If the AP your Router is go[...]

300M Wireless N Router RNX-N300RT User Manual ¾ Disable Security - If you do not want to use wireless security, check this radio button. But it’s strongly recommended to choose one of the following modes to enable security. ¾ WEP - It is based on the IEEE 802.11 standard. If you check this radio button, you will find a notice in red as show in [...]

300M Wireless N Router RNX-N300RT User Manual ¾ WP A /WP A2-Enterprise - It’s based on Radius Server. • Ve r s i o n - you can choose the vers ion of the WPA security on the pull-down list. The default setting is Automatic , which can select WP A ( Wi-Fi Protected Access) or WP A2 ( W PA version 2) automatically based on the wireless station&a[...]

300M Wireless N Router RNX-N300RT User Manual encryption, you will find a not ice in red as shown in Figure 4-21 . Figure 4-21 • PSK Passphrase - You can enter a Passphrase between 8 and 63 characters. • Group Key Up date Period - Specify the group key update interval in seconds. The value should be 30 or above. En ter 0 to disable the update. [...]

300M Wireless N Router RNX-N300RT User Manual ¾ Description - A simple description of the wireless station. To Add a Wireless MAC Address filtering entry, click the Add New… button. The " Add or Modify Wireless MAC Address Filtering entry " page will appear , shown in Figure 4-23 : Figure 4-23 Add or Modify Wireless MAC Address Filteri[...]

300M Wireless N Router RNX-N300RT User Manual For example: If you desire that th e wireless statio n A with MAC add ress 00-0A-EB-B 0-00-0B and the wireless s tation B with MAC address 00-0A -EB-00-07-5 F are able to access th e Router, but all the other wireless stations canno t access the Rou ter, you can configur e the Wirele ss MAC Address Filt[...]

300M Wireless N Router RNX-N300RT User Manual Figure 4-24 Wireless Advanced ¾ Transmit Power - Here you can specify the transmit power of Router. You can select High, Middle or Low which you woul d like. High is the default setting and is recommended. ¾ Beacon Interval - Enter a value between 20-1000 m illiseconds for Beacon Interval here. The be[...]

300M Wireless N Router RNX-N300RT User Manual Intervals. The default value is 1, which indi cates the DTIM Interval is the same as Beacon Interval. ¾ Enable WMM - WMM function can guarantee the pa ckets with high-priority messages being transmitted preferenti ally. It is strongly recommended. ¾ Enable Short GI - This function is recommended for i[...]

300M Wireless N Router RNX-N300RT User Manual ¾ Sent Packets - Packets sent by the station You cannot change any of the values on this page. To update this page and to show the current connected wirele ss stations, click on the Refresh button. If the numbers of connected wireless st ations go beyond one page, click the Next button to go to the nex[...]

300M Wireless N Router RNX-N300RT User Manual Figure 4-27 DHCP Setting s ¾ DHCP Server - Enable or Disable the DHCP server . If you disable the Server , you must have another DHCP server within your network or else you must configure the computer manually . ¾ St art IP Address - S pecify an IP address for the DHCP Server to start with when assign[...]

300M Wireless N Router RNX-N300RT User Manual ¾ Secondary DNS - (Optional.) Input th e IP address of another DNS server if your ISP provides two DNS servers. ) Note: To use the DHCP server function of the Rout er, you must configure all computers on the LAN as "Obtain an IP Address automatically". 4.7.2 DHCP Client s List Choose menu “[...]

300M Wireless N Router RNX-N300RT User Manual Figure 4-29 Address Reservation ¾ MAC Address - The MAC address of the PC for which you want to reserve an IP address. ¾ Reserved IP Address - The IP address reserved for the PC by the Router. ¾ Status - The status of this entry, either Enabled or Disabled . To Reserve an IP address: 1. Click the Add[...]

300M Wireless N Router RNX-N300RT User Manual Click the Enable/Disabled All button to make all entries enabled/disabled Click the Delete All button to delete all entries. Click the Next button to go to the next page and Click the Previous button to return the previous page. 4.8 Forwarding Figure 4-31 T he Forwarding menu There are four submenus und[...]

300M Wireless N Router RNX-N300RT User Manual Figure 4-32 Virtual Servers ¾ Service Port - The numbers of External Ports. Y ou can type a service port or a range of service ports (in XXX – YYY form at, XXX is the start port number , YYY is the end port number). ¾ IP Address - The IP Address of the PC pr oviding the service application. ¾ Proto[...]

300M Wireless N Router RNX-N300RT User Manual Figure 4-33 Add or Modify a Virtual Server Entry ) Note: If your computer or server has more than one type of available service, please select another service, and enter the same IP A ddress for that computer or server . To modify or delete an existing entry: 1. Click the Modify in the entry you want to[...]

300M Wireless N Router RNX-N300RT User Manual can work with an NA T Router . Figure 4-34 Port T riggering Once the Router is configured, the operation is as follows: 1. A local host makes an outgoing connecti on using a destination port number defined in the T rigger Port field. 2. The Router records this connection, opens the incoming port or port[...]

300M Wireless N Router RNX-N300RT User Manual 2. Select a common application from the Common Applications drop-down list, then the T rigger Port field and the Incoming Ports field will be automatically filled. If the Common Applications do not have the applicati on you need, enter the T rigger Port and the Incoming Port s manually . 3. Select the p[...]

300M Wireless N Router RNX-N300RT User Manual ) Note: 1) When the trigger connec tion is released, the corre sponding opening ports will be closed. 2) Each rule is allowed to be used only by one host on LAN synchronously . The trigger connection of other hosts on LAN will be refused. 3) Incoming Port Range cannot overlap each other . 4.8.3 DMZ Choo[...]

300M Wireless N Router RNX-N300RT User Manual Figure 4-37 UPnP ¾ Current UPnP Status - UPnP can be enabled or di sabled by clicking the Enable or Disable button. ¾ Current UPnP Settings List - This table displays the current UPnP information. • App Description - The description provided by the application in the UPnP request. • External Port [...]

300M Wireless N Router RNX-N300RT User Manual 4.9.1 Basic Security Choose menu “ Security → Basic Security ”, you can configure the basic security in the screen as shown in Figure 4-39 . Figure 4-39 Basic Security ¾ Firewall - A firewall protects your network fr om the outside world. Here you can enable or disable the Router’s firewall. z [...]

300M Wireless N Router RNX-N300RT User Manual z IPSec Passthrough - Internet Protocol Security (I PSec) is a suite of protocols for ensuring private, secure communications over Internet Protoc ol (IP) networks, through the use of cryptographic securi ty services. To allow IPSec tunnels to pass through the Router, keep the default, Enabled . ¾ ALG [...]

300M Wireless N Router RNX-N300RT User Manual Figure 4-40 Advanced Security ¾ Packets Statistics Interval (5~60) - The default value is 10. Select a value between 5 and 60 seconds from the drop-down list. T he Packets S tatistics Interval value indicates the time section of the p ackets stat istics. The result of the statistics is used for analysi[...]

300M Wireless N Router RNX-N300RT User Manual ¾ UDP-FLOOD Packets Threshold (5~3600) - The default value is 500. Enter a value between 5 ~ 3600. When the current U PD-FLOOD Packets number is beyond the set value, the Router will startup t he blocking function immediately. ¾ Enable TCP-SYN-FLOOD Attack Filtering - Enable or Disable the TCP-SYN-FLO[...]

300M Wireless N Router RNX-N300RT User Manual By default, the radio button “ All the PCs on the LAN are allowed to access the Router's Web-Based Utility ” is checked. If you want to allow PCs with specific MAC Addresses to access the Setup page of the R outer's Web-Based Utilit y locally from inside the network, check the radio button[...]

300M Wireless N Router RNX-N300RT User Manual ¾ Remote Management IP Address - This is the current address you will use when accessing your Router from the Interne t. This function is disabled when the IP address is set to the default value of 0.0.0. 0. To enable this func tion change 0.0.0.0 to a valid IP address. If set to 255.255.255.255, then [...]

300M Wireless N Router RNX-N300RT User Manual the screen as shown in Figure 4-44 . Figure 4-44 Access Control Rule Management ¾ Enable Internet Access Control - Select the check box to enable the Internet Access Control function, so the Def ault Filter Policy can take effect. ¾ Rule Name - Here displays the name of the rule and this name is uniqu[...]

300M Wireless N Router RNX-N300RT User Manual 3. Select a host from the Host drop-down list or choose “ Click Here To Add New Host List ”. 4. Select a targ et from the Target drop-sown list or choose “ Click Here To Add New Target List ”. 5. Select a sch edule from the Schedule drop-down list or choose “ Click Here To Add New Schedule ”[...]

300M Wireless N Router RNX-N300RT User Manual 1. Click “ Access Control → Host ” in the left to enter the Host Settings page. Add a new entry with the Host Descrip tion is Host_1 and MAC Address is 00-11-22-33-44-AA. 2. Click “ Access Control → Target ” in the left to enter the Target Settings page. Add a new entry with the Target Descr[...]

300M Wireless N Router RNX-N300RT User Manual Figure 4-46 Host Settings ¾ Host Description - Here displays the description of the host and this description is unique. ¾ Information - Here displays the information about the host. It can be IP or MAC. ¾ Modify - To modify or delete an existing entry. To add a new entry, please follow the steps bel[...]

300M Wireless N Router RNX-N300RT User Manual Figure 4-47 Add or Modify a Host Entry Figure 4-48 Add or Modify a Host Entry For example : If you desire to restrict the inter net activities of host with MAC address 00-11-22-33-44-AA, you should first follow the settings below: 1. Click Add New... button in Figure 4-46 to enter the Add or Modify a Ho[...]

300M Wireless N Router RNX-N300RT User Manual Figure 4-49 T arget Settings ¾ Target Description - Here displays the description about the target and this description is unique. ¾ Information - The target can be an IP address, a port, or a domain name. ¾ Modify - To modify or delete an existing entry. To add a new entry, please follow the steps b[...]

300M Wireless N Router RNX-N300RT User Manual Click the Next button to go to the next page, or click the Previous button return to the previous page. Figure 4-50 Add or Modify an Access T arget Entry Figure 4-51 Add or Modify an Access T arget Entry For example : If you desire to restrict the inter net activities of host with MAC address 00-11-22-3[...]

300M Wireless N Router RNX-N300RT User Manual 4. In Domain Name field, enter www.google.com. 5. Click Save to complete the settings. Then you will go back to the Target Settings page and see the following list, 4.10.4 Schedule Choose menu “ Access Control → Schedule ”, you can view and set a Schedule list in the next screen as shown in Figure[...]

300M Wireless N Router RNX-N300RT User Manual 5. Click Save to complete the settings. Click the Delete All button to delete all the entries in the table. Click the Next button to go to the next page, or click the Previous button return to the previous page. Figure 4-53 Advanced Schedule Settings For example : If you desire to restrict the inter net[...]

300M Wireless N Router RNX-N300RT User Manual 4.1 1 Advanced Routing Figure 4-54 Advanced Routing There are two submenus under the Adv anced Routing menu as shown in Figure 4-54 : St atic Routing List and System Routing T able . Click any of them, and you will be able to configure the co rresponding function. 4.1 1.1 St atic Routing List Choose men[...]

300M Wireless N Router RNX-N300RT User Manual Figure 4-56 Add or Modify a S tatic Route Entry 2. Enter the following data. ¾ Destination IP Address - The Destination IP Address is the address of the network or host that you want to assign to a static route. ¾ Subnet Mask - The Subnet Mask determines which portion of an IP Address is the network p[...]

300M Wireless N Router RNX-N300RT User Manual views all of the valid route entries in us e. The Destination IP address, Subnet Mask, Gateway , and Interface will be displayed for each entry . Figure 4-57 System Routing T able ¾ Destination Network - The Destination Network is t he address of the network or host to which the static route is assigne[...]

300M Wireless N Router RNX-N300RT User Manual Figure 4-59 Bandwidth Control Settings ) Note: For optimal control of the band width, please select the right bandwidth type and ask your ISP for the total bandwidth of the egress and ingress. 4.12.2 Rules List Choose menu “ Bandwidth Control → Rules List ”, you can view and configure the Bandwidt[...]

300M Wireless N Router RNX-N300RT User Manual Step 2: Enter the information like the screen shown below . Figure 4-61 Bandwidth Control Rule Settings Step 3: Click the Save button. 4.13 IP& MAC Binding Settings Figure 4-62 the IP & MAC Binding menu There are two submenus under the IP &MAC Binding menu (shown in Figure 4-62 ): Binding Se[...]

300M Wireless N Router RNX-N300RT User Manual Figure 4-63 Binding Settings ¾ MAC Address - The MAC address of the controll ed computer in the LAN. ¾ IP Address - The assigned IP address of the cont rolled computer in the LAN. ¾ Bind - Check this option to enable ARP binding for a specific device. ¾ Modify - To modify or delete an existing entry[...]

300M Wireless N Router RNX-N300RT User Manual To find an existing entry, follo w the steps below. 1. Click the Find button as shown in Figure 4-63 . 2. Enter the MAC Address or IP Address. 3. Click the Find button in the page as shown in Figure 4-65 . Figure 4-65 Find IP & MAC Binding Entry Click the Enable All button to make all entries enable[...]

300M Wireless N Router RNX-N300RT User Manual z Load - Load the item to the IP & MAC Binding list. z Delete - Delete the item. Click the Bind All button to bind all the current items, available after enable. Click the Load All button to load all items to the IP & MAC Bind ing list. Click the Refresh button to refresh all items. ) Note: An i[...]

300M Wireless N Router RNX-N300RT User Manual Figure 4-67 Comexe.cn DDNS Settings To set up for DDNS, follow these instructions: 1. T ype the Domain Name received from your dynamic DNS service provider . 2. T ype the User Name for your DDNS account. 3. T ype the Password for your DDNS account. 4. Click the Login button to log in to the DDNS service[...]

300M Wireless N Router RNX-N300RT User Manual Figure 4-68 Dyndns.org DDNS Settings To set up for DDNS, follow these instructions: 5. T ype the User Name for your DDNS account. 6. T ype the Password for your DDNS account. 7. T ype the Domain Name you received from dynamic DNS service provi der here. 8. Click the Login button to log in to the DDNS se[...]

300M Wireless N Router RNX-N300RT User Manual Figure 4-69 No-ip.com DDNS Settings To set up for DDNS, follow these instructions: 1. T ype the User Name for your DDNS account. 2. T ype the Password for your DDNS account. 3. T ype the Domain Name you received from dynamic DNS service provider . 4. Click the Login button to log in the DDNS service. Co[...]

300M Wireless N Router RNX-N300RT User Manual 4.15 System T ools Figure 4-70 The System T ools menu Choose menu “ System T ools ”, you can see the subm enus under the main menu: Tim e Settings , Diagnostic , Firm ware Upgrade , Factory Defaults, Backup & Restore, Reboot, Password, System Log and St atistics. Click any of them, and you will [...]

300M Wireless N Router RNX-N300RT User Manual Figure 4-71 T ime settings ¾ Time Zone - Select your local time zone from this pull down list. ¾ Date - Enter your local date in MM/ DD/YY into the right blanks. ¾ Tim e - Enter your local time in HH/MM/SS into the right blanks. ¾ NTP Server Prior - Enter the address for the NTP Server , then the Ro[...]

300M Wireless N Router RNX-N300RT User Manual ) Note: 1) This setting will be used for some time-based functions such as firewall. You must specify your time zone once you log in to the Router successfully, otherwise, these functions will not take effect. 2) The time will be lost if the Router is turned off. 3) The Router will obtain GMT aut omatic[...]

300M Wireless N Router RNX-N300RT User Manual z T raceroute - This diagnostic tool tests the performance of a connection. ) Note: You can use ping/traceroute to test both numeric IP address or domain name. I f pinging/tracerouting the IP address is succe ssful, but pinging/tr acerouting the domain name is not, you might have a name resolution probl[...]

300M Wireless N Router RNX-N300RT User Manual 4.15.3 Firmware Upgrade Choose menu “ System T ools → Firmw are Upgrade ”, you can update the latest version of firmware for the Router on the following screen. Figure 4-74 Firmware Upgrade ¾ Firmware Version - This displays the current firmware version. ¾ Hardware Version - This displays the cu[...]

300M Wireless N Router RNX-N300RT User Manual 3) Do not turn off the Router or press the Reset bu tton while the firmware is being upgraded, otherwise, the Router may be damaged. 4) The Router will reboot after the upgrading has been finished. 4.15.4 Factory Defaults Choose menu “ System T ools → Factory Defaults ”, and you can restore the co[...]

300M Wireless N Router RNX-N300RT User Manual ¾ T o upgrade the Router's configurat ion, follow these instructions. • Click the Browse… button to locate the upd ate file for the Router , or enter the exact path to the Setting fi le in the text box. • Click the Restore button. ) Note: The current configuration will be covered by the uplo[...]

300M Wireless N Router RNX-N300RT User Manual 4.15.7 Password Choose menu “ System T ools → Password ”, you can change the fa ctory default user name and password of the Router in the next screen as shown in Figure 4-78 . Figure 4-78 Password It is strongly recommended that you shoul d change the factory default user name and password of the [...]

300M Wireless N Router RNX-N300RT User Manual Figure 4-79 System Log ¾ Auto Mail Feature - Indicates whether auto mail feature is enabled or not. ¾ Mail Settings - Set the receiving and sending mailbox address, server address, validation information as well as the timet able for Auto Mail Feature, as shown in Figure 4-80 . -109-[...]

300M Wireless N Router RNX-N300RT User Manual Figure 4-80 Mail Account Settings z From - Your mail box address. The Router would connect it to send logs. z To - Recipient’s address. The destination mail box where the logs would be received. z SMTP Server - Your smtp server. It corresponds wi th the mailbox filled in the From field. You can log on[...]

300M Wireless N Router RNX-N300RT User Manual z Confirm The Password - Enter the password again to confirm. z Enable Auto Mail Feature - Select it to mail logs au tomatically. You could mail the current logs either at a spec ified time everyday or by intervals, but only one could be the current effective rule. Enter the desired ti me or intervals i[...]

300M Wireless N Router RNX-N300RT User Manual Figure 4-81 S tatistics ¾ Current Statistics Status - Enable or Disable. The def ault value is disabled. To enable, click the Enable button. If disabled, the functi on of DoS protection in Security settings will be disabled. If disabled, t he function of DoS protection in Security settings will be disa[...]

300M Wireless N Router RNX-N300RT User Manual Statistics Table: IP Address/ MAC Address The IP Address and MAC address are displayed wit h related statistics Packets The total number of packets received and transmitted by the Router. Total Byt es The total number of bytes received and transmitted by the Router. Packets The total number of packets r[...]

300M Wireless N Router RNX-N300RT User Manual Appendix A: FAQ 1. How do I configure the Router to access the Internet by ADSL users? 1) First, configure the ADSL Modem configured in RFC1483 bridge model. 2) Connect the Ethernet cable from yo ur ADSL Modem to the W AN port on the Router . The telephone cord plugs into the Line port of the ADSL Modem[...]

300M Wireless N Router RNX-N300RT User Manual ) Note: 1) Sometimes the connection cannot be disconnected although you specify a time to Max Idle T ime, since some applications is visiting the Internet continually in the background. 2) If you are a Cable user , please confi gure the Router following the above steps. 2. How do I configure the Router [...]

300M Wireless N Router RNX-N300RT User Manual 3) How to configure Virtual Server: Log in to the Router , click the “ Forw arding ” menu on the left of your browser , and click " Virtual Servers " submenu. On the " Virtual Servers " p age, click Add New… . Then on the “ Add or Modify a Virtual Server Entry ” page, enter[...]

300M Wireless N Router RNX-N300RT User Manual Figure A-6 DMZ 5) How to enable H323 ALG: Log in to the Router , click the “ Security ” menu o n the left of your browser , a nd click “ Basic Security ” submenu. On the “ Basic Security ” page, check the Enable radio button next to H323 ALG . Remember to click the Save button. Figure A-7 Ba[...]

300M Wireless N Router RNX-N300RT User Manual submenu. On the " Remote Management " page, type a port number except 80, such as 88, into the "W eb Management Port" field. Click Save and reboot the Router . Figure A-8 Remote Management ) Note: If the above configuration takes effect, configure to the Router by typing 192.168.1.1:[...]

300M Wireless N Router RNX-N300RT User Manual Figure A-10 Add or Modify a Virtual server Entry 5. The wireless st ations cannot connect to the Router . 1) Make sure the " Enable Wireless Router Radio " is checked. 2) Make sure that the wireless stations' SSID accord with the Router's SSID. 3) Make sure the wireless stations have[...]

300M Wireless N Router RNX-N300RT User Manual Appendix B: Configuring the PC In this section, we’ll introduce how to inst all and co nfigure the TCP/IP correctly in Windows XP . First make sure your Ethernet Ad apter is working, refer to the adapter ’s manual if necessary . 1. Configure TCP/IP component 1) On the Windows taskbar , click the St [...]

300M Wireless N Router RNX-N300RT User Manual Figure B-2 5) The following TCP/IP Properties window will display and the IP Address tab is open on this window by default. Now you have two ways to configure the TCP/IP protocol below: ¾ Setting IP address automatically Select Obt ain an IP address automatically , Choose Obt ain DNS server automatical[...]

300M Wireless N Router RNX-N300RT User Manual Figure B-3 ) Note: For Windows 98 OS or before, the PC and Router may need to be restarted. ¾ Setting IP address manually 1 Select Use the following IP address radio button. And the fo llowing items available 2 If the Router's LAN IP addre ss is 192.168.1.1, specify the IP address as 192.168.1.x ([...]

300M Wireless N Router RNX-N300RT User Manual Figure B-4 Now: Click OK to keep your settings. -123-[...]

300M Wireless N Router RNX-N300RT User Manual Appendix C: Specifications General St andards IEEE 802.3, IEEE 802.3u, IEEE 802.1 1b, IEEE 802.1 1g and IEEE 802.1 1n Protocols TCP/IP , PPPoE, DHCP , ICMP , NA T , SNTP Port s One 10/100M Auto-Negotiation WAN RJ45 port, Four 10/100M Auto-Negotiation LAN RJ45 ports supporting Auto MDI/MDIX 10BASE-T : UT[...]

300M Wireless N Router RNX-N300RT User Manual Appendix D: Glossary ¾ 802.11n - 802.11n builds upon previous 802. 11 standards by adding MIMO (multiple-input multiple-output). MIMO uses multiple transmitter and receiver antennas to allow for increased data th roughput via spatial multiplexing and increased range by exploiting the spatial di versity[...]

300M Wireless N Router RNX-N300RT User Manual ¾ DSL ( D igital S ubscriber L ine) - A technology that allows data to be sent or received over existing traditional phone lines. ¾ ISP ( I nternet S ervice P rovider) - A company that provides access to the Internet. ¾ MTU ( Maximum Transmission Unit ) - The size in bytes of the largest packet that [...]