Profile HA1000 manual

MOSFET POWER AMPLIFIERS Installation Instructions / Owner's Manual HA1000 HA740 HA1040 HA600 HA400 HA700M HA1000M[...]

1 Serial # Model # I NTRODUCTION Congratulations on your purchase of a Baja state-of-the-art power amplifier. Your selection of a Baja car audio product indicates a true appreciation of fine musical reproduction. Whether adding to an existing system or including your Baja amplifier in a new system, you are certain to notice immediate performance be[...]

2 S AFETY PRECAUTIONS battery in case of a short circuit between the power amplifier and battery. THIS IS A MUST. The amplifier's built-in fuse will only protect the power amplifier and not the car's battery! The fuse value is based on the amplifiers rated power and how many amplifiers will be run off the same power wire. Please see the s[...]

3 Built-in Crossover The Baja amplifiers include a built-in variable **high and low pass crossovers. The crossover features a variable frequency selection of (80 Hz ~ 1.2k Hz) for precise high pass filter and (50 Hz ~ 250 Hz) for low pass filter. ** HA1000, HA700M and HA1000M models only have a 50 Hz ~ 250 Hz low pass filter. F EATURES AND BENEFITS[...]

Tri-Mode Capable (Excluding HA700M & HA1000M models) If so desired the amplifier may be run in stereo and mono at the same time. For example, this feature would allow you to run a pair of mids and tweeters in stereo and a subwoofer in mono. 4 Remote Turn-on Automatically turns amplifier on when connected to the head unit's remote output. T[...]

5 Short Circuit Protection The circuit protects the amplifier from damage due to a short found in the speakers or wiring. If one of the speakers or its wiring comes in contact with ground, the amplifier will shut down. To resume normal operation, correct the problem and turn the head unit off, then back on. The amplifier will reset and play again. [...]

6 P OWER CONNECTIONS Connect the B+ terminal of the amplifier to the car's battery. At times, the amplifier will need to draw large levels of current that cannot be provided by any circuit in the car's fuse box. We recommended using a 4 to 10 gauge power wire (red) for your connections depending on the amplifier size and length of the wir[...]

7 M OUNTING LOCATION Before you start the installation, it will be necessary to find a mounting location for the amplifier. Find a location in which the amplifier will receive adequate ventilation in order to dissipate the heat it develops during operation. Two popular mounting locations are in the trunk or under the seat. Select the location in wh[...]

8 TWO CHANNEL SIGNAL CONNECTIONS FOUR CHANNEL SIGNAL CONNECTIONS (RADIO WITH FRONT AND REAR OUTPUTS) FRONT REAR Connect 2 sets of RCA "Y" adaptors to split the two RCA's from the radio into 4 outputs (Not Provided) FOUR CHANNEL SIGNAL CONNECTIONS (RADIO WITH ONLY ONE SET OF RCA'S) Connect the RCA output of the head unit (AM/FM c[...]

will allow you to connect directly to the speaker output of the radio, without the need of an external adapter. GND 9 connect the amplifier to a factory radio without low-level RCA outputs. This connection High level inputs have been included in all Baja amplifiers excluding 4 Channel amps to H IGH LEVEL CONNECTIONS (OPTIONAL) GRAY LEFT + BLACK CHA[...]

10 Make the speaker connections using speaker wire that is at least 14 gauge or heavier. As with any audio component, proper phasing of the amplifier and speakers is essential for strong bass response. When connecting, make sure that positive (+) from the amplifier is connected to the positive (+) of the speaker, and the same for negative (-). S PE[...]

11 S PEAKER CONNECTIONS (BRIDGED) Two and four channel amplifiers are capable of being bridged ** into a mono configuration. This feature allows you the flexibility of using the amplifier to drive a subwoofer or a center channel. In this configuration the amplifier sums the right and left channel to deliver one channel (mono) output. Please note: I[...]

12 NON-POLAR CAPACITOR INDUCTOR (COIL) L E G E N D Left Mid / Tweeter 4 Ohm (2 Ohm Minimum) Mono Woofer 8 Ohm (4 Ohm Minimum) Right Mid / Tweeter 4 Ohm (2 Ohm Minimum) ¹ F 100 ¹ F 100 CAUTION! In Tri- mode operation, the amplifier must see a 2 Ohm load or higher for the stereo satellites and no lower than 4 Ohms for the subwoofer(s). Any lower th[...]

13 Select the crossover type on the amplifier's side panel. ( High-pass is selected in this example for tweeters/midranges ) (Please note: If you intend to use the amplifier in the Tri-mode configuration, it is necessary to set the crossover control to the "Full" setting in order to receive full range output) The Baja amplifiers are [...]

14 control until the system gets loud but before the point of distortion. It is very important S ETTING THE GAIN The gain control has been included to allow adjustment to properly To properly set the gain, start by setting the gain to its minimum position and turn the main radio volume up to 3/4 of maximum volume control. Then slowly raise the amp [...]

15 T ROUBLE SHOOTING THE SYSTEM We have put together this trouble-shooting guide if you experience problems after installing the amplifier. Please keep in mind that the majority of problems incurred are caused by improper installation and not the equipment itself. In addition, there are many components in the system that could cause various signal [...]

16 S PECIFICATIONS HA400 HA600 2 x 130W 2 x 65W 2 x 200W 2 x 100W 1 x 200W Yes <0.07% 20Hz ~ 30kHz >100dB 83dB Yes 200mV ~ 7V 20K Ohms 42 Ohms 2 ~ 8 Ohms 4 ~ 8 Ohms HP / FULL / LP 50Hz ~ 250Hz 80Hz ~ 1.2kHz 0dB ~ 12dB - - - - - 320 20A 2 1/4 " x 9 11/16 " x 9 1/16 " 2 x 200W 2 x 100W 2 x 300W 2 x 150W 1 x 300W Yes <0.07% 20H[...]

S PECIFICATIONS Max Power Output@4 Ohm RMS Power Output@4 Ohm Max Power Output@2 Ohm RMS Power Output@2 Ohm MOSFET Power Supply THD@RMS Power Frequency Response Signal To Noise Stereo Separation Pre-Amp Output RCA Input Voltage RCA Input Impedance High Level Input Impedance Load Impedance Mono Crossover Type(12dB/Octave) LP Crossover Frequency(Vari[...]

Profile Consumer Electronics, Inc. warrants this product to be free from defects in material and workmanship for a period of One (1) Year from the date of sale to the original consumer purchaser. If this product is proven to be defective within this one year period, Profile will repair it when said product is returned, with a copy of the dated sale[...]

15060 SHOEMAKER AVE. By PROFILE CONSUMER ELECTRONICS, INC. SANTA FE SPRINGS, CA 90670 TEL: (562) 404-9393 FAX: (562) 404-9433 www.profileusa.com 15060 SHOEMAKER AVE. SANTA FE SPRINGS, CA 90670 In the unlikely event of product failure, the following procedures 2) The unit must have no physical damage. 1) The unit must be under the 1-year warranty pe[...]