PowerPlus POWX0782 manual

POWX0782 EN Copyrigh t © 2015 VARO P a g e | 1 www .varo.com 1 APPLIC A TION ................................................................................. 4 2 DESCRIPTION ................................................................................ 4 3 PACKAGE CONT ENT LIST ............................................................ 4 4 SY[...]

POWX0782 EN Copyrigh t © 2015 VARO P a g e | 2 www .varo.com 10.1.6 Bevelling (Fig. 10 and Fig. 11) ................................................................................ 13 10.1.7 Sawing the w orkpiece: ........................................................................................... 13 10.1.8 Double mitre cu t ...............[...]

POWX0782 EN Copyrigh t © 2015 VARO P a g e | 3 www .varo.com 14 W ARRANTY .................................................................................. 22 15 ENVIRONM ENT ............................................................................ 22 16 DECL ARATION OF CONF ORM ITY ............................................. 23[...]

POWX0782 EN Copyrigh t © 2015 VARO P a g e | 4 www .varo.com CROSS-CUT AND MITRE SAW WITH TOP TABLE POWX0782 1 APPLIC A T ION The machine is designed for saw ing wood, metal and plastic. I t is not designed for commercial use. WARN ING! Read this manual and genera l safety i nstructions ca refully before using the appliance, for y o ur own safety [...]

POWX0782 EN Copyrigh t © 2015 VARO P a g e | 5 www .varo.com 4 SYMBO LS In this manual and / or on the machine the follow ing symbols are used: Denotes risk of personal injury or da mage to the tool . In accordance with essential requirements o f the Europe an directive(s) Read manual befor e use "Class II - The mach ine is double insulated; [...]

POWX0782 EN Copyrigh t © 2015 VARO P a g e | 6 www .varo.com  Avoid accidental start s. Ensure the switch is in the off position befor e inserting the plug. Carrying power tools with you r finger on the switch or plug ging in po wer tools when the switch is in the on position makes acciden ts more like ly.  Remove any adjusting keys or spa n[...]

POWX0782 EN Copyrigh t © 2015 VARO P a g e | 7 www .varo.com  Only use saw blad es that are reco mm ended by the manufac turer and that ful fil the EN847- 1 standard. Also make sure the riving knife is not thi cker than the width of the saw cut, and that it is not thinner than the bo dy of the saw blade.  Always use the a ccessories that are[...]

POWX0782 EN Copyrigh t © 2015 VARO P a g e | 8 www .varo.com  Do not carry out any free-hand ope rations. Free-hand means that yo u us e your hand s for supporting the w orkpiece, or for leading it w ith your hand s , instead o f using the rip fence or the mitre blo ck.  NEVER bend over or around the saw blad e. NEVER reach for a wo rkpi ece[...]

POWX0782 EN Copyrigh t © 2015 VARO P a g e | 9 www .varo.com 9 INSTALL A T ION AND TR ANSPORT Do not carry the machine on the handgrip; the handgrip is not designed to car ry the full weight of the mac hine. For carry ing the machine, hold it on both edges of t he base (12). 9.1 Installat ion (Fig. 14)  Get help from anothe r person for l iftin[...]

POWX0782 EN Copyrigh t © 2015 VARO P a g e | 10 www .varo.com 9.2.2 Cross- cu t and mitre saw operating mode (Fig. 6)  Make sure that the mitre and w idth guide (4) i s correctly installed and that the saw blade i s covered. This ac tivates sw itch A (8). Ma ke sure that the cover ( m itre and width gu ide) is firmly attached. If this is not th[...]

POWX0782 EN Copyrigh t © 2015 VARO P a g e | 11 www .varo.com  Follow the user instru ctions for the dust collector . 9.2.7 Connection to AC powe r High-voltage!  Only operate this ma c hine in dry surround ings.  This machine may on ly be connec ted to a pow er source that fulfils th e following requirements (al so see the sec tion "[...]

POWX0782 EN Copyrigh t © 2015 VARO P a g e | 12 www .varo.com Before starting w ith the installa tion of the machine: - Switch the mach ine “OFF” - Remove the p lug from the s ocket - Wait until at the machine has come to a c omplete standstill  The mitre and width gu ide (4) mus t be installed, so that the saw blade can be covered and safe[...]

POWX0782 EN Copyrigh t © 2015 VARO P a g e | 13 www .varo.com  The saw should be switched off by releasing the switch (20), if no furth er sawing ha s to be done. 10.1.5 Mitre sawing (Fig. 7)  During mitre saw ing, the w orkpiece is saw ed at an angle in relation to the mitre and width guide.  Starting position: - Saw head co mpletely rai[...]

POWX0782 EN Copyrigh t © 2015 VARO P a g e | 14 www .varo.com 10.1.8 Double mitre cu t  A double mitre cut is a combination of a mitre cut and a bevelling cut; th is means that the workpiece is cu t at an angle in the one single move ment, which is no t equal to 90° in relation to the mi tre and w idth guide and the material sur face. HAZA RD![...]

POWX0782 EN Copyrigh t © 2015 VARO P a g e | 15 www .varo.com  Replace the push block when da maged. 10.2.5 Installation HAZA RD! Before starting w it h the installa tion of the machine: - Switch the mach ine “OFF” - Remove the p lug from the s ocket - Wait until at the machine has come to a c omp lete standstill  Leave the saw hea d in [...]

POWX0782 EN Copyrigh t © 2015 VARO P a g e | 16 www .varo.com 10.2.6 Sawing HAZA RD! Always use a push block, if the distance D of the workpiece is less than 120 mm (Fig. 17).  The front edge of the saw blade g uard m ust res t on the workpiece.  If necessary, install the mitre and w idth guide, and make sur e that th e locking screw points [...]

POWX0782 EN Copyrigh t © 2015 VARO P a g e | 17 www .varo.com  Check the powe r cable and plug f or damages, and let da maged part s be replaced by a certified electri cian.  Check all moving par ts, and ma ke sure that the y can move freely and smoo thly over their entire operational ra nge.  Check the riving knife, and make s ure that t[...]

POWX0782 EN Copyrigh t © 2015 VARO P a g e | 18 www .varo.com  Remove the shaft bolt (E1) and th e outer saw flange (E2) fro m the saw shaft.  Remove the saw blade (18) fro m the saw shaf t and lift it up to remove it fro m the machine.  Remove the shaft nu t (E4) and th e inner saw flange (E3) fro m t he saw s haft.  Clean the surface[...]

POWX0782 EN Copyrigh t © 2015 VARO P a g e | 19 www .varo.com  The spanner must be re moved, after the shaft that ha s been tightene d.  Install the saw table and mount th e c orresponding screw s. 11.2.6 Tightening the driv e belt The drive belt, w hic h is located behind a pla s tic cover at the right-hand side of the saw head, must be ten[...]

POWX0782 EN Copyrigh t © 2015 VARO P a g e | 20 www .varo.com 11.3 Modifications 11.3.1 Modifications on the mitre and width guide (Fig . 27)  Loosen the attach ment screws (L1 ) of the guide.  Adapt the guide so tha t it is po sitioned ex actly at right angles to the saw blade, whe n the mitre table (11) i s in the 0° po sition.  Retigh[...]

POWX0782 EN Copyrigh t © 2015 VARO P a g e | 21 www .varo.com 12 TECHNIC AL DAT A Mains voltage 220 - 240 V ~ 50Hz Power 1800 W Saw blade rp m 5000 min -1 Saw blade di m ensions 254 x 30 x 3 mm - 60T TCT Cutting capac ity : As Table saw : 4 6 mm As mitre saw : 0x90° H70x W 110mm 45°x90° H4 0x W 11 0mm 0°x45° H7 0x W 70mm 45°(L)x45° 45°(R)x[...]

POWX0782 EN Copyrigh t © 2015 VARO P a g e | 22 www .varo.com 14 W ARRANTY  This product is w arranted for a 36- month period e ffective fro m the date of pu rchase by the first user.  This warra nty covers all material or production flaws ex c luding : batt eries, charger s, defective parts subject to nor m al w ear & tear such a s bear[...]