Português dropdown-ico

Poulan Pro PP291E30 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40

Ir para a página of

Manuais similares

Bom manual de uso

As regras impõem ao revendedor a obrigação de fornecer ao comprador o manual com o produto Poulan Pro PP291E30. A falta de manual ou informações incorretas fornecidas ao consumidor são a base de uma queixa por não conformidade do produto com o contrato. De acordo com a lei, pode anexar o manual em uma outra forma de que em papel, o que é frequentemente utilizado, anexando uma forma gráfica ou manual electrónicoPoulan Pro PP291E30 vídeos instrutivos para os usuários. A condição é uma forma legível e compreensível.

O que é a instrução?

A palavra vem do latim "Instructio" ou instruir. Portanto, no manual Poulan Pro PP291E30 você pode encontrar uma descrição das fases do processo. O objetivo do manual é instruir, facilitar o arranque, a utilização do equipamento ou a execução de determinadas tarefas. O manual é uma coleção de informações sobre o objeto / serviço, um guia.

Infelizmente, pequenos usuários tomam o tempo para ler o manual Poulan Pro PP291E30, e um bom manual não só permite conhecer uma série de funcionalidades adicionais do dispositivo, mas evita a formação da maioria das falhas.

Então, o que deve conter o manual perfeito?

Primeiro, o manual Poulan Pro PP291E30 deve conte:
- dados técnicos do dispositivo Poulan Pro PP291E30
- nome do fabricante e ano de fabricação do dispositivo Poulan Pro PP291E30
- instruções de utilização, regulação e manutenção do dispositivo Poulan Pro PP291E30
- sinais de segurança e certificados que comprovam a conformidade com as normas pertinentes

Por que você não ler manuais?

Normalmente, isso é devido à falta de tempo e à certeza quanto à funcionalidade específica do dispositivo adquirido. Infelizmente, a mesma ligação e o arranque Poulan Pro PP291E30 não são suficientes. O manual contém uma série de orientações sobre funcionalidades específicas, a segurança, os métodos de manutenção (mesmo sobre produtos que devem ser usados), possíveis defeitos Poulan Pro PP291E30 e formas de resolver problemas comuns durante o uso. No final, no manual podemos encontrar as coordenadas do serviço Poulan Pro na ausência da eficácia das soluções propostas. Atualmente, muito apreciados são manuais na forma de animações interessantes e vídeos de instrução que de uma forma melhor do que o o folheto falam ao usuário. Este tipo de manual é a chance que o usuário percorrer todo o vídeo instrutivo, sem ignorar especificações e descrições técnicas complicadas Poulan Pro PP291E30, como para a versão papel.

Por que ler manuais?

Primeiro de tudo, contem a resposta sobre a construção, as possibilidades do dispositivo Poulan Pro PP291E30, uso dos acessórios individuais e uma gama de informações para desfrutar plenamente todos os recursos e facilidades.

Após a compra bem sucedida de um equipamento / dispositivo, é bom ter um momento para se familiarizar com cada parte do manual Poulan Pro PP291E30. Atualmente, são cuidadosamente preparados e traduzidos para sejam não só compreensíveis para os usuários, mas para cumprir a sua função básica de informação

Índice do manual

  • Página 1

    OWNER'S MANUAL MODEL NUMBER: PP291E30 SNOW THROWER Always W ear Eye Protection During Operation IMPORT ANT MANU AL Do Not Throw Away WARNING: Read the Owner's Manual and fol low all W arnings and Safety In struc tions. F ail ure to do so can result in serious injury . 428548 Rev 1 07.13.09 TH Printed in U.S.A.[...]

  • Página 2

    2 IMPORT ANT Safe Operation Practices for W alk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. F ailure to observe the following safety instructions could result in serious injury . WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. Caution should be e[...]

  • Página 3

    3 CONGRA TUL A TIONS on your purchase of a new snow thrower . It has been designed, engineered and man u - fac tured to give best possible dependability and per for - mance. Should you experience any problem you cannot easily remedy , please contact your nearest authorized service center . We have competent, well-trained tech ni cians and the prope[...]

  • Página 4

    4 P ARTS P ACKED SEP ARA TEL Y IN CARTON (3) RET AINER SPRINGS (169675) (1) WASHER 3/8 (19131316) (1) L OCKNUT 3/8 (73800600) (2) SAFTEY IGNITION KEY (422663) (1) MUL TI- WRENCH (180684) (1) L OCKNUT 5/16-18 (751153) (1) CARRIAGE BOL T 5/16-18 x 5/8 (72250505) (1) L OCKNUT 1/4-20 (191730) (1) SHOULDER BOL T 1/4-20 (179829) (1) SPRING (184505) (1) P[...]

  • Página 5

    5 Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower . Reading the entire manual will familiar- ize you with the unit, which will assist you in assembly , operation and maintenance of the product. Y our new snow thrower has been as sem bled at the factory with the ex cep tion of t[...]

  • Página 6

    6 AS SEMBL Y / PRE-OPERA TION INST ALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4) The traction drive control rod is installed on the snow thrower . 1. Remove plastic tie securring rod to lower handle. 2. With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. S[...]

  • Página 7

    7 AS SEMBL Y / PRE-OPERA TION INST ALL DISCHARGE CHUTE / CHUTE ROT A TOR HEAD (See Fig. 7) NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotator head. 1. Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower . 2. Position chute rotator head over chute bracket. If[...]

  • Página 8

    8 OPERA TION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERA TING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literat[...]

  • Página 9

    9 OPERA TION Drive speed control lever - used to select forward or reverse motion and speed of snow thrower . T raction drive control lever - used to engage power - pro pelled for ward or reverse motion of snow thrower . Auger control lever - used to engage auger motion (throw snow). Discharge chute control lever - used to change the di- rec tion t[...]

  • Página 10

    10 TO CONTROL SNOW DISCHARGE (See Fig. 13) WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup. If the discharge chute or au ger become clogged, shu[...]

  • Página 11

    11 OPERA TION TO THROW SNOW (See Fig. 14) The auger rotation is controlled by the auger control lever located on the right side handle. • Squeeze auger control lever to handle to engage the auger and throw snow . • Release the auger control lever to stop throwing snow . USING THE CLEAN-OUT TOOL (See Fig. 15) In certain snow conditions, the disc[...]

  • Página 12

    12 BEFORE ST ARTING THE ENGINE CHECK ENGINE OIL LEVEL (See Fig. 19) The engine on your snow thrower has been shipped, from the factory , already filled with oil. 1. Check engine oil with snow thrower on level ground. 2. Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wait for a few seconds, remove and read oil le[...]

  • Página 13

    13 OPERA TION TO ST ART ENGINE • Be sure fuel shut-off valve is in the “OPEN” position. Y our snow thrower engine is equipped with both a 120 V olt A.C. electric starter and a recoil starter . The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 V olt A .C. household current. • Be sure you[...]

  • Página 14

    14 SAE 5W -30 Motor Oil See “ENGINE” in Maintenance section General Purpose Grease GENERAL REC OM MEN DA TIONS The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. T o receive full value from the warranty , operator must maintain snow thrower as in struct ed in this manual. Some ad j[...]

  • Página 15

    15 MAINTENANCE AUGER GEAR CASE • The gear case was filled with lubricant to the proper level at the factory . The only time the lubricant needs attention is if service has been performed on the gear case. • If lubricant is required, use only Ronex ED #1 grease. TRACTION DRIVE SYSTEM DO NOT lubricate the drive components inside the snow thrower [...]

  • Página 16

    16 SERVICE AND ADJUSTMENTS BEL T COVER SCREWS FRAME FIG. 21 TO REMOVE BEL T COVER (See Fig. 21) 1. Remove the two (2) screws securing belt cover to frame. 2. Remove belt cover . • Replace belt cover by installing cover and screws and tighten securely . WARNING: T o avoid serious injury , before performing any service or ad just ments: 1. Be sure [...]

  • Página 17

    17 SERVICE AND ADJUSTMENTS 8. RELIEVE TENSION ON TRACTION DRIVE BEL T IDLER and remove traction drive belt from around pulleys. HINT : Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension. 9. With tension relieved on idler , install new traction drive belt arou[...]

  • Página 18

    18 SERVICE AND ADJUSTMENTS ENGINE See engine manual. CARBURETOR Y our carburetor is not adjustable. Engine performance should not be affected at altitudes up to 2,134 meters. If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a service center/department. ENGINE SPEED Never tamper with the engine[...]

  • Página 19

    19 STORAGE Immediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more. WARNING: Never store the snow thrower with gaso line in the tank in side a build ing where fumes may reach an open flame, spark or pilot light as on a fur nace, water heater , clothes dryer or gas ap pli ance. Allow the[...]

  • Página 20

    20 TROUBLESHOOTING Does not start 1. Fuel shut-off valve (if so 1. T urn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key . is not inserted. 3. Out of fuel. 3. Fill fuel tank with fresh, clean gasoline. 4. Throttle in STOP position 4. Move throttle to FAST position (or ON/OFF swit[...]

  • Página 21

    21 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003000) AUGER HOUSING / IMPELLER ASSEMBL Y NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . 1 2 3 (5x) 4 [...]

  • Página 22

    22 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003000) AUGER HOUSING / IMPELLER ASSEMBL Y NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . 10 11 11 11 1[...]

  • Página 23

    23 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003000) AUGER HOUSING / IMPELLER ASSEMBL Y NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO [...]

  • Página 24

    24 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003000) AUGER HOUSING / IMPELLER ASSEMBL Y NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO [...]

  • Página 25

    25 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003000) AUGER HOUSING / IMPELLER ASSEMBL Y NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO [...]

  • Página 26

    26 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003000) CONTROL P ANEL / DISCHARGE CHUTE NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . [...]

  • Página 27

    27 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003000) CONTROL P ANEL / DISCHARGE CHUTE NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . [...]

  • Página 28

    28 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003000) HANDLES NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION KEY P AR[...]

  • Página 29

    29 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003000) HANDLES NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . 1 2 3 3 4 4 3 3 01.08.004-B 4 4 KEY P AR[...]

  • Página 30

    30 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003000) HANDLES NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION 10 11 1 [...]

  • Página 31

    31 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003000) HANDLES NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION 10 10 10[...]

  • Página 32

    32 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003000) DRIVE NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . 9 9 11 11 11 1 2 3 21 5 6 12 13 14 15 20 1[...]

  • Página 33

    33 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003000) DRIVE NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION KEY P ART [...]

  • Página 34

    34 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003000) DRIVE NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION 1a 1b 1b 4[...]

  • Página 35

    35 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003000) CHAS SIS / ENGINE / PULLEYS NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . [...]

  • Página 36

    36 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003000) CHAS SIS / ENGINE / PULLEYS NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . [...]

  • Página 37

    37 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003000) WHEELS NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION 1 2 01.06[...]

  • Página 38

    38 REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003000) BAG OF P ARTS NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION KE[...]

  • Página 39

    39 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . REP AIR P ARTS SNOW THROWER - MODEL PP291E30 (96198003000) DECALS 1 181037 DECAL, DANGER 2 181042 DECAL, DA[...]

  • Página 40

    LIMITED W ARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and work man ship. For a period of two (2) years from date of purchase by the original consumer pur - chaser , we will repair or replace, at our option, without charge for parts or labor incurred in repl[...]