POSIFLEX Business Machines Jiva TP/LT - 5815 manual

Part 1 FCC Notes: This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause interference to radio communications. It has been tested and found to comply wit h limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules, which are [...]

Part 2 ALERT TO OUR HONORABLE CUSTOMERS: l Please always rea d thoroughly all the instructions and documents delivered with the product before you do anything about it. Don’t take any premature action before you have a full understanding of the consequences. l This product contains inside a Lithium battery and maybe a lso a sealed type Lead acid [...]

Part 3 IN TRODUCTION PRODUCT PICTURES Front Views Side Views Slim Base Models Universal Base Models Slim Base Models Universal Base Models 11 11 12 1 12 12 10 10 7 5 13 13 5 7 1 Slim Base Models 7 3 4 1 1 Universal Base Models 4 5 6 9 8 8 9 10 10 7 5 2 2 Slim Base Models Universal Base Models[...]

Part 4 Rear Views Bottom Views PARTS IDENTIFICATION 1. Main unit 2. Touch panel / LCD panel 3. Option al side mount kit 4. Power status indicator 5. Universal base stand 6. Optional CDROM drive 7. Slim base stand 8. Cable cover 9. Removal hollow in cable cover 10. Lock / release lever for tilt angle adjust Slim Base Models Universal Base Models 1 1[...]

Part 5 11. Optional rear top mount kit PD - 302 12. Lock / release button for main unit d etach 13. Power switch 14. Rear connect cover 15. Power connector hole 16. Cable exit 17. 2 nd cable exit 18. Auxiliary cable exit 19. Rubber feet 20. Bottom plate 21. Bottom plate fixing screw 22. 2.5 ” HDD window 23. 2.5 ” HDD bracket cover 24. 2.5 ” H[...]

Part 6 5. 2 USB ports 6. one LAN port 10/100 base T Ethern et 7. one external VGA monitor port 8. one IDE connector and HDD power connector for HDD in base 9. one 4 pin lock type DC 12 V power input connector 10. one UPS battery connector 11. one CR port for control over 2 cash drawers max. 12. audio ports (1 Microphone input and 2 op tional slim t[...]

Part 7 i) IDE interface internal slim type CD ROM drive or COMBO in base for universal base models j) UPS battery in base k) Preload OS l) 2 in 1 cash drawer control cable (CCBLA - 238) m) Wall mount kit: WB - 6000, WB - 6300, WB - 6600, WB - 6800[...]

Part 8 INSTALLATION GUIDES CAUTION: Before any installation or cable connection to the set, please always make certain that the system is turned off and the external power source to the set is removed to prevent electric hazard! Never touch any metal pin in the connectors or circuits to avoid high voltage hazard or electrostatic discharge damage un[...]

Part 9 SEPARATING MAIN UNIT I n order to settle the touch terminal properly in a point of s ervice system, all the cable connections have to be routed through its base, either slim or universal. Therefore, please observe the procedures from A to C below to separate the main unit from bo th slim and universal base stand assembly after all cables in [...]

Part 10 model will lo ok like the right picture above . Both with numbered items listed as below . However, there could be some variation to the contents inside depending on what option items actually installed. When the HDD installed is the 2.5 ” type, the HDD mounting bracket, the met al base chassis and the bottom plate will also look differen[...]

Part 11 WB - 6300 WB - 6600 WB - 6800 WB - 6000 as in left picture. Put the battery in at the other end first and remount the bracket with its tongue matching under a bridge in the wall of base box from the right as arrowed in above left pictur e then apply the fixing screw. Please pay particular attention to the environment requirements for UPS ba[...]

Part 12 backpack into the cable cover area of main unit. The area required for wall mount application is determined by the main unit dimensions and is 37 6 mm in width and 315 mm in height. BASE MOUNT UPGRADE KIT On rear edge of the stand assembly for desktop mount application, there is a rear connect cover. Either a 2nd LCD display panel option LM[...]

Part 13 15” 2 nd LCD Panel Please follow the installation instruction that come alone with the 15 ” 2 nd LCD monitor LM - 6301 to mount the interface bracket kit onto the LCD panel . Fit the interface bracket the same way as joint base of LM - 6201 to the rear connect opening and fix with 2 screws with washers. Route the VGA through the cable e[...]

Part 14 WIRELESS PRINTER To access the Posiflex wireless thermal printer PP7700 in Windows environment except Win CE , a wireless Dongle DG2000 for this printer must be separately purchased and installed to one of the serial COM ports in Jiva system. Please enable the + 5 V DC power supp ort for this COM port. Hook the Dongle to either top corner o[...]

Part 15 such as the external VGA, LPT and COM connector be screwed into place onc e seated. If the COM1 port must be used, the COM1 terminator that occupies the COM1 port must be removed and safely preserved for future use . However, when using the COM1 port, it is advisable to use devices that provide proper hardware handshaking signals in order t[...]

Part 16 USING THE TOUCH TERMINAL APPLICATION ENVI RONMENT It is very important to check the following operational guidelines: Ventilation This terminal must NOT be used in an environment with restricted ventilation. There must be at least 25 mm air clearance around any ventilation holes with a free flow o f air around the unit at ALL times for the [...]

Part 17 Power Supply The operating voltage range of the power adaptor should cover the local power supply for proper op eration. The power cable, the power outlet and any power fusing arrangements must conform to local safety regulations. Please never do any connection / disconnection when system is still powered on. Please always keep the external[...]

Part 18 make sure that the software application has the ability to power off the machine. In preloaded Windows, “Posiflex Power Switch Manager” in “Posiflex Tools” in th e Program Files helps managing these functions. Software Support Features The Jiva series provides a software power off for application program maneuvers as mentioned above[...]

Part 19 supply the required power through the VGA connector for LM - 6212. Do not connect other monitor to this port before the power in this port is disabled. CUSTOME R DISPLAY Please follow the instructions on the manual that comes along with the customer display PD - 2501 or PD - 2602 when it is installed. SERIAL PORTS The serial ports i n Jiva [...]

Part 20 T OUCH PANEL All paragraphs below are applicable for models with touch panel only. The user of those models without touch panel can ignore them and consider this user ’ s manual ends here. Mouse Emulation The touch panel in Jiva system uses USB interface as st andard. Only the optional InfraRed type touch panel uses RS232 interface. When [...]