Pelco CC3710UH SERIES manual

Installa tion/Oper a tion CC3610UH and CC3710UH Series Color Camer a C2933M (10/05) Pelco Worldwide Headquarters • 3500 Pelco Way, Clovis, CA 93612-5699 USA • www.pelco.com USA & Canada: Tel 800/289-9100 • FAX 800/289-9150 International: Tel: 1-559/292-1981 • FAX 1-559/348-1120[...]

[ 2 ] Pelco Manual C2933M (10/05) ® Pelco, the Pelco logo, Spectra, Genex, Legacy , Esprit and Camclosure are registered trademarks of Pelco. ™Endura and ExSite are trademarks of Pelco ™DLP is a trademark of T exas Instruments, Inc. ™SuperHAD CCD is a trademark of the Sony Corporation. © Copyright 2005, Pelco. All rights reserved.[...]

Pelco Manual C2933M (10/05) [ 3 ] CONTENTS IMPORT ANT SAFETY INSTRUCTIONS ........................................................................................................... 4 REGULA TORY NOTICES ............................................................................................................. .................... 5 DESCRIPTION .[...]

[ 4 ] Pelco Manual C2933M (10/05) This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. This symbol indicates that there are impor- tant operating and maintenance instructions in the literature accompanying this unit. Please thoroughly familiarize yourself with the information in this manual[...]

Pelco Manual C2933M (10/05) [ 5 ] REGULA T OR Y NOTICES This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISI[...]

[ 6 ] Pelco Manual C2933M (10/05) DESCRIPTION CC3610UH and CC3710UH Series cameras are color video cameras with a 1/3-inch CCD imager . All cameras have a direct drive/auto iris lens connector and adjustable back focus, and they accept C and CS lenses. Models CC3610UH-6 Ultra-high resolution (540 TV lines), Exview HAD™ CCD, 0.4 lux at F1.2, NTSC,[...]

Pelco Manual C2933M (10/05) [ 7 ] CAMERA LA Y OUT Figure 1. Camera Layout INST ALLA TION Lens Mounting CC3610UH and CC3710UH Series cameras can use fixed iris, manual iris, auto iris, or direct drive lenses. Cameras are factory-set for CS-mount lenses, but are easily adjusted for C-mount lenses. 1. C-Mount Lens Onl y - Loosen the two back focus loc[...]

[ 8 ] Pelco Manual C2933M (10/05) Camera Mounting Mounting points are provided on the top and bottom of the camera and are used to mount the camera on a bracket or tripod. They are designed to accept standard photographic mounting bolts (1/4-inch UNC-20). The mounting bracket must be capable of supporting the weight of the camera and its lens. NO T[...]

Pelco Manual C2933M (10/05) [ 9 ] CONNECTIONS CC3610UH and CC3710UH Series cameras offer standard power and coax video connectors as well as an RJ45-10 connector that combines low voltage power and video (composite or UTP). These cameras also have a service connector allowing a video monitor to be connected locally to the camera using a composite v[...]

[ 10 ] Pelco Manual C2933M (10/05) Low V olt age Power Supply Cameras fitted with an automatic-switching low voltage power supply operate at 10.8 to 13.8 VDC (12 VDC -10% +15%) or 20.4 to 27.6 V AC (24 V AC ±15%) at 50/60Hz. Connections and polarity are indicated adjacent to the screw terminals on the rear panel. Refer to T able B for the recommen[...]

Pelco Manual C2933M (10/05) [ 11 ] RJ45-10 Connections The RJ45-10 connector allows video (composite and twisted pair) and power connections to be made to the camera using a single Cat5-style cable. NO TE: The PCM150 camera mount is designed for the CC3610UH and CC3710UH Series camera. It comes with preconfigured auxiliary connectors and cables as [...]

[ 12 ] Pelco Manual C2933M (10/05) Ser vice Connection The service connector allows a video monitor to be connected locally to the camera using a 2.5 mm plug to composite video BNC cable. Figure 5. Service Connector NO TE: Inserting the plug into the service connector disconnects video from the composite BNC connector on the rear panel of the camer[...]

Pelco Manual C2933M (10/05) [ 13 ] CAMERA SETUP Lens Setup and Focus Procedures Video Drive or Direct Drive (DC) Auto Iris Lens 1. Set the ESC switch and AGC switch to OFF . 2. Adjust the lens for the optimum picture. Video Drive Refer to the lens instructions and adjust the lens for the optimum picture (video output level of 1 V peak-to-peak). Dir[...]

[ 14 ] Pelco Manual C2933M (10/05) Back F ocus Adjustment The back focus adjustment is located at the front of the camera and is accessible from either side of the case. T o adjust the back focus: 1. Loosen the two back focus locking screws (one on each side). 2. T urn the back focus ring counterclockwise until the CCD sensor assembly is as far awa[...]

Pelco Manual C2933M (10/05) [ 15 ] Switch Settings NO TE: Under most conditions, no setting of switches will be required. Please read the details of each switch before making any adjustments. AGC (Automatic Gain Control) - Switch Setting 1 Automatically adjusts the image to compensate for low levels of illumination. Choose between the following set[...]

[ 16 ] Pelco Manual C2933M (10/05) Flickerless - Switch Setting 4 The flickerless setting can reduce the flicker caused by certain lighting conditions. The Electronic Shutter Control must be off for the correct operation of the flickerless function and is therefore automatically disabled. Choose between the following settings: ON - Enables the Flic[...]

Pelco Manual C2933M (10/05) [ 17 ] Camera Synchronization When using more than one camera power supply , a brief vertical roll may occur on the monitor when a camera view is switched. T o eliminate this vertical roll, it is necessary for the cameras to be synchronized. If the cameras are connected to certain Pelco matrix products, the cameras will [...]

[ 18 ] Pelco Manual C2933M (10/05) SPECIFICA TIONS GENERAL Imaging Device: 1/3-inch interline transfer CCD Picture Elements CC3610UH and CC3710UH: NTSC 768 (H) x 494 (V); P AL 752 (H) x 582 (V) Sensing Area: 6 mm diagonal Scanning System NTSC: 525 lines, 2:1 interlace P AL: 625 lines, 2:1 interlace Synchronization System: AC line lock/internal Hori[...]

Pelco Manual C2933M (10/05) [ 19 ] ENVIRONMENT AL Operating T emperature: 14° to 122°F (-10° to 50°C) Storage T emperature: 14° to 158°F (-10° to 70°C) Operating Humidity: 20% to 80%, non-condensing Storage Humidity: 20% to 90%, non-condensing PHY SICAL Dimensions: 5" L x 2.9" W x 2.6" H (12.8 x 7.2 x 6.7 cm) Weight (without [...]

[ 20 ] Pelco Manual C2933M (10/05)[...]

Pelco Manual C2933M (10/05) [ 21 ][...]

[ 22 ] Pelco Manual C2933M (10/05) If the goods are to be sent by a FREIGHT FORWARDER, send the goods to: Pelco c/o Expeditors 473 Eccles Avenue South San Francisco, CA 94080 USA Phone: 650-737-1700 Fax: 650-737-0933 PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in ma[...]

Pelco Manual C2933M (10/05) [ 23 ] REVISION HIST ORY Manual # Date Comments C2933M 10/05 Original version.[...]

[ 24 ] Pelco Manual C2933M (10/05) Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com www.pelco.com www.pelco.com www.pelco.com www.pelco.com ISO 9001 9001 9001 9001 9001 United States | Canada | United Kingdom | [...]