ParaBody 848 manual

1 848 LA T OPTION CLASS H PAR T # 7080301 REV . B Revision: 07/10/01 USER’S GUIDE W ARNING: Read and follow all directions for each step to insure proper assembly of this product. V ersion: 848107[...]

THERE IS A RISK ASSU MED BY IND IVIDUALS W HO USE T HI S TYPE OF EQUIPMENT. TO MINIMIZE RISK F OLLOW THESE RULE S ! 1. Before u sing, read al l the w arnings and in structions on the use of this mach ine. Use only for in tended exercise. DO NOT mo dify the m achine. 2. Obtain a medica l exam bef ore begi nning any exercise pro gram. 3. Keep body a [...]

IMPOR T ANT NOTES Please note: T ools Required for Assembly * Thank you for purchasing the ParaBody 848 LA T OPTION. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. * Rubber mallet or hammer * 3/4” wrench * 9/16” wrench * Ratchet[...]

4 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 P AR TS LIST PA R T # 6826608 6826908 6825408 6827208 6825502 6275302 6274402 6542402 6824801 3103102 31 16201 6177001 6405201 6467001 6692601 6825101 KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 QTY 1 1 1 1 1 1 1 2 2 4 6 2 4 2 3 1 PA R T # 31 16001 6140701 3102501 3102802 3102502 3102801 3102933 3102903 3102922[...]

FIGURE 1 STEP 1: • SECUREL Y assemble the one 3/8 X 2-3/4” BOL T (25), two 3/8” W ASHERS (19), and one 3/8” LOCK NUT (20) to the ST AND (3) as shown in FIGURE 1. • Assemble two 2” SQ. COVER CAPS (14) onto the ends of the ST AND (3) as shown in FIGURE 1. • Insert two 3 X 2” END CAP (15) into the ends of the BASE (1) as shown in FIGUR[...]

6 FIGURE 4 STEP 3: • Assemble one 17-1/2” FOAM STRIP (16) to the underside of the CROSS BRACE (4) as shown in FIGURE 3. • Assemble two 2-1/2 X 5-1/2” NON-SKID STRIPS (12) to the CROSS BRACE (4) as shown in FIGURE 3. FIGURE 3 STEP 4: • SECUREL Y attach one 1-1/4” SQ. RUBBER BUMPER (17) to the CARRIAGE (5) as shown in FIGURE 4. • Insert[...]

7 STEP 5: FIGURE 5 • Slide the CARRIAGE (5) over the UPRIGHT (2) as shown in FIGURE 5. • Assemble the ST AND (3) to the UPRIGHT (2) as shown in FIGURE 5. 1 3 5 2 • Assemble the BASE (1) to the UPRIGHT (2) as shown in FIGURE 5.[...]

STEP 6: FIGURE 6 • SECUREL Y assemble the BASE (1) to the UPRIGHT (2) using one 1/2 X 3” BOL T (27), two 1/2” W ASHERS (21) (slide front washer INSIDE of tube) , and one 1/2” LOCK NUT (22). See FIGURE 6. • Insert one 3 X 2” END CAP (15) and one 2” SQ. END CAP (13) into the ends of the UPRIGHT (2) as shown in FIGURE 6. • SECUREL Y as[...]

9 STEP 7: FIGURE 7 • Route the CABLE (9) through the UPRIGHT (2) as shown in FIGURE 7. • SECUREL Y assemble three 3-1/2” PULLEYS (1 1) into the slots of the UPRIGHT (2) using three 3/8 X 2-3/4” BOL TS (25), six 3/8” FLANGE SP ACERS (31), and three 3/8” LOCK NUTS (20) as shown in FIGURE 7. (NOTE: Make sure the cable is r outed over all t[...]

10 STEP 8: FIGURE 8 23 3/8 X 2” 19 19 20 9 8 29 2 5 • Place one 3-1/2” PULLEY (11) into the loop of the CABLE (9) below the second and third PULLEY of the UPRIGHT (2) as shown in FIGURE 8. • LOOSEL Y assemble two 3/16 X 1-3/4 X 5-1/4” PLA TES (8) to each side of the 3-1/2” PULLEY (11) using one 3/8 X 2” BOL T (23), two 3/8” W ASHERS[...]

11 STEP 9: FIGURE 9 23 3/8 X 2” 19 19 20 9 11 2 • Route the end of the second CABLE (9) through the slot on the UPRIGHT (2) then SECUREL Y assemble one 3-1/2” PULLEY (1 1) to the UPRIGHT (2) using two 3/8 X 2-1/2” BOL TS (24), two 3/8 X 3/8” SP ACERS (30), four 3/8” W ASHERS (19), and two 3/8” LOCK NUTS (20). (NOTE: The CABLE (9) shou[...]

12 STEP 10: FIGURE 10 • SECUREL Y assemble the CABLE (9) to the BASE (1) using one 3/8 X 4-1/2” BOL T (26), one 3/8 X 1” SP ACER (32), and one 3/8” LOCK NUT (20) as shown in FIGURE 10. 9 26 3/8 X 4-1/2” 1 32 20 0 1 2 34 1/2 1/2 1/2 1/2[...]

13 STEP 1 1: FIGURE 1 1 • Attach the LA T BAR (6) to the ball end of the upper CABLE (9) using one 5/16” SNAP HOOK (28) as shown in FIGURE 11. • Attach the LOW ROW BAR (7) to the ball end of the lower CABLE (9) using one 5/16” SNAP HOOK (28) as shown in FIGURE 11. • Slide two 1 X 8” GRIPS (10) on the LOW ROW BAR (7) and two 1 X 8” GRI[...]

STEP 12: FIGURE 12 • Tilt the 848101 back and remove the ST AND (3) as shown in FIGURE 12. • T o use the 848101 LA T OPTION: (NOTE: LA T OPTION MUST BE USED WITH A BENCH. LA T OPTION CANNOT BE USED WHILE ST AND IS A TT ACHED. ST AND MUST BE A TT ACHED WITH THE FEET OUT AS SHOWN.) 14 3 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2[...]

Thank you for pur chasing the Parabody 848 LA T OPTION. If unsure of proper use of equipment, call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714. BENCH 2 STEP 13: FIGURE 13 • Insert the UPRIGHT (2) of the 848 into the bench as shown in FIGURE 13. 15[...]

MAINTENANCE MODEL #________________________ SERIAL #_________________________ DA TE OF PURCHASE: _____________ DEALERS NAME: _________________ DEALERS PHONE #_______________ 16 * W e recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water . T ouch-up paint can be purchased from your ParaBody customer service repr[...]

17 NOTES: LIMITED W ARRANTY ParaBody extends the following LIMITED W ARRANTY to the original owner of the ParaBody products. The W arranty terms apply to IN HOME USE ONL Y . 1. LIMITED W ARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repair ed or replaced by ParaBody . T erms: Lifetime ?[...]

INTERNA TIONAL OFFICES LifeFitnessAtlantic BV Atlantic Headquarters Bijdorpplein 25-31 2992 LB Barendrecht The Netherlands Phone: (180) 646 666 Fax: (180) 646 703 LifeFitness Japan 8/F , Nippon Brunswick Building 5-27-7 Sendagaya Shibuya-Ku, T okyo 151-0051 Japan Phone: 81 (3) 3359-4309 Fax: 81 (3) 3359-4307 LifeFitness (UK) Ltd. Queen Adelaide Ely[...]