Oregon Scientific RMR613HGA manual

W ireless Thermo-Hygro Clock Model : RMR613HGA User Manual RMR613HGA lab test cover R 2 1/8/04, 7:02 PM 1[...]

EN 1 CONTENTS Contents ................................................................... 1 Introduction .............................................................. 2 About Oregon Scientific .......................................... 2 Product Overview .................................................... 3 Front View ...........................[...]

EN 2 INTRODUCTION Thank you for selecting the Oregon Scientific TM Wireless Thermo-Hygro Clock (RMR613HGA). This device bundles precise time keeping, dual alarm, and temperature and humidity monitoring features into a single tool you can use from the convenience of your home. In this box, you will find: • Main unit • Remote sensor (THGR122NX) K[...]

EN 3 PRODUCT OVERVIEW FRONT VIEW 1. Clock / Alarm Area: Date, time, dual alarm; and Atomic Clock reception status 2. T emperature Area: Readings; sensor channel number; remote unit reception and battery status 3. Humidity / Comfort Zone Area: Readings, comfort zone and battery status. 4. Channel button: switch remote sensor 5. Alarm button: view al[...]

EN 4 BACK VIEW 1. MEM: view current, maximum, and minimum temperature / humidity readings 2. DOWN: decrease setting / deactivate radio- controlled clock / activate or deactivate alarm 3. UP: increase setting / activate radio-controlled clock / activate or deactivate alarm 4. MODE: change display / settings 5. Battery compartment 6. ° C / ° F swit[...]

EN 5 REMOTE SENSOR (THGR122NX) 1. LCD display 2. LED Status indicator 1 2 1 2 3 4 1. W all mount hole 2. RESET 3. Channel number (1 - 3) 4. Battery compartment (Battery compartment cover not shown) RMR613HGA lab test R2 1/17/04, 5:00 PM 5[...]

EN 6 CHANGE SETTINGS 1. Press and hold MODE for 2 seconds to enter setting mode. 2. Press UP or DOWN to change settings. 3. Press MODE to confirm. REMOTE SENSOR (THGR122NX) This product is shipped with a THGR122NX Thermo/ Hygro Sensor that collects T emperature and Humidity data. Data can be collected from up to 3 sensors. Additional sensors sold s[...]

EN 7 3. Place the sensor near the main unit. Press RESET on the sensor to initiate signal sending between the sensor and the main unit. The reception icon on the main unit will blink for approximately 3 minutes while it is searching for the sensor . (Refer to the Search for Sensor section for more information.) 4. Close the remote sensor battery co[...]

EN 8 SEARCH FOR SENSOR To search for a sensor , press and hold MEM and CHANNEL for 2 seconds. If the sensor is still not found, check the batteries, obstructions, and remote unit location. Signals from household devices such as doorbells, electronic garage doors, and home security systems may cause temporary reception failure. This is normal and do[...]

EN 9 TURN A TOMIC CLOCK ON/OFF Perform this step if you cannot receive Atomic Clock signals. Press and hold DOWN for 2 seconds. Then, manually set the clock following the “Set Clock” instructions (below). SET CLOCK Y ou only need to do this if you have disabled the Atomic Clock feature (for example, if you are too far from or cannot receive a s[...]

EN 10 ACTIV A TE ALARM Press ALARM to switch to Weekday or Single Alarm view . To activate or deactivate the alarm, press UP or DOWN . • Alarm deactivated: --:-- • Alarm activated: Alarm time is shown The bell icons W and S indicate the alarm display mode selected. SILENCE ALARM When the Alarm time is reached, the crescendo alarm will sound for[...]

EN 11 To auto-scan between sensors, press and hold CHANNEL for 2 seconds. Each sensor's data will be displayed for 3 seconds. T o end auto-scan, press CHANNEL or MEM . If you use a sensor that collects only temperature data, humidity will not be shown. MINIMUM / MAXIMUM RECORDS Press MEM to toggle between current, maximum (MAX) and minimum (MI[...]

EN 12 Do not make any changes or modifications to this product. Unauthorized changes may void your right to use the product. The technical specification of this product and contents of this user guide are subject to change without notice. Images not drawn to scale. TROUBLESHOOTING Check here before contacting our customer service department. Proble[...]

EN 13 Problem Symptom Remedy Data does not match main unit Initiate a manual sensor search ( 8) Cannot change channel Check sensors. Only one sensor is working ( 6) Check batteries ( 6) Check location ( 6) Remote sensor Cannot locate remote sensor SPECIFICA TIONS MAIN UNIT DIMENSIONS L x W x H 123 x 49.5 x 165 mm (4.84 x 19.5 x 6.50 inches) We ight[...]

EN 14 Calendar MM/DD; weekday in 5 languages (E, D, F , I, S) Alarm Weekday and Single Alarm; 2- minute crescendo POWER Main unit batteries 2 x UM-3 (AA) 1.5V alkaline Sensor batteries 2 x UM-4 (AAA) 1.5V alkaline FCC ST A TEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This devic[...]

EN 15 DECLARA TION OF CONFORMITY The information below is not to be used as contact for support or sales. Please call our customer service number (listed on our website at www .oregonscientific.com, or on the warranty card for this product) for all inquiries instead. We Name: Oregon Scientific, Inc. Address: 19861 SW 95 th Place, T ualatin, Oregon [...]

P/N.: 086-003326-01 © 2004 Oregon Scientific. All rights reserved. RMR613HGA lab test back cover 12/29/03, 10:49 PM 1[...]