Makita PV7001C manual

INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. www .makitatools.com Electr onic P olisher 180 mm (7”) MODEL PV7001C 003431[...]

2 SPECIFICATIONS • Manuf acturer reser v es the right to change specifications without notice. • Specifications ma y differ from countr y to country . GENERAL SAFETY R ULES USA001-2 (F or All T ools ) W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , ma y result in electr ic shoc k, fire and/or [...]

3 5. A void bod y contact with grounded sur- faces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is g rounded. 6. Do not expose po wer tools to rain or wet conditions. W ater enter ing a pow er tool will increase the risk of electr ic shoc k. 7. Do not abuse the cor d. Never use the co[...]

4 SER VICE 23. T ool service must be performed onl y by qualified repair personnel. Service or main- tenance perf ormed by unqualified personnel could result in a risk of injur y . 24. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized par ts or f ailure to[...]

5 An adapter Fig. “ B ” and “ C ” is av ailable f or connecting Fig. “ A ” type plugs to two-prong receptacles. The g reen-colored rigid ear , lug, etc., extending from the adapter m u st be con- nected to a per manent g round, such as a properly grounded outlet bo x. SPECIFIC SAFETY R ULES USB047-3 DO NO T let comf or t or familiarity [...]

6 9. Do not leave the tool running. Operate the tool only when hand-held. 10. Do not touch the w o rkpiece immediatel y after operation; it may be e xtremely hot and could burn y our skin. 11 . Check that the w orkpiece is properly sup- ported. 12. P ay attention that the wheel continues to rotate after the tool is s witched off. 13. This tool has [...]

7 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is s witched off and unplugged bef ore adjusting or checking function on the tool. Switch action CA UTION: • Bef ore plugging in the tool, always chec k to see that the s witch tr igger actuates properly and retur ns to the “ OFF ” position when released. • Switch can be l[...]

8 • Electronic constant speed contr ol P ossible to get fine finish, because the rotating speed is kept constantly e ven under the loaded condition. • Soft start feature Soft star t because of suppressed star ting shock. High-Low speed setting b utton The tool speed can be changed instantly while the tool is running. Depress the “ I ” posit[...]

9 Installing or remo ving backing pad Hold the spindle with the wrench so that it cannot re volv e. Then screw the pad onto the spindle all the w ay . (The pad can be used to install the optional sponge pad.) T o remov e the pad, follo w the installation procedure in re verse . Installing or remo ving sponge pad (optional accessory) T o install the[...]

10 Fit the wool bonnet completely o v er the rubber pad and pull the string tight. Tie a bow knot and tuck the knot and an y loose strings between the wool bonnet and the rubber pad. T o remov e the wool bonnet, f ollow the installation procedure in re verse. Installing or remo ving abrasive disc (optional accessory) NO TE: • Use sander accessori[...]

11 P olishing operation by w ool bonnet CA UTION: • Alwa ys wear saf ety glasses or a face shield during operation. Hold the tool fir mly . T urn the tool on and then apply the wool bonnet to the workpiece. In general, k eep the wool bonnet at an angle of about 15 degrees to the workpiece surf ace. Apply slight pressure only . Excessive pressure [...]

12 Use a screwdriv er to remove the brush holder caps. T ake out the worn carbon br ushes, inser t the new ones and secure the brush holder caps. T o maintain product SAFETY and RELIABILITY , repairs, any other maintenance or adjustment should be perf or med by Makita A uthor ized or F actor y Ser vice Centers, alw ays using Makita replacement par [...]

13 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut[...]

14 1. This product was pur chased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom F riend Previous Usage Other ( ) 2. Use of the pr oduct is intended for: Construction T rad[...]

15 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ALABAMA 2365 Pelham P arkway Pelham, AL 35124 (205) 620-1791 ARIZONA 3707 E. Broadw ay Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 ARKANSAS Shackleford Shopping Center 240 South Shackleford Rd., Ste. C Little Rock, AR 72211 (501) 224-5733 CALIFORNIA 41850 Chris[...]

W ARNING Some dust created by po wer sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th def ects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • cr ystalline silica from bricks and cement and othe[...]