Makita DCS461 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36

Ir para a página of

Bom manual de uso

As regras impõem ao revendedor a obrigação de fornecer ao comprador o manual com o produto Makita DCS461. A falta de manual ou informações incorretas fornecidas ao consumidor são a base de uma queixa por não conformidade do produto com o contrato. De acordo com a lei, pode anexar o manual em uma outra forma de que em papel, o que é frequentemente utilizado, anexando uma forma gráfica ou manual electrónicoMakita DCS461 vídeos instrutivos para os usuários. A condição é uma forma legível e compreensível.

O que é a instrução?

A palavra vem do latim "Instructio" ou instruir. Portanto, no manual Makita DCS461 você pode encontrar uma descrição das fases do processo. O objetivo do manual é instruir, facilitar o arranque, a utilização do equipamento ou a execução de determinadas tarefas. O manual é uma coleção de informações sobre o objeto / serviço, um guia.

Infelizmente, pequenos usuários tomam o tempo para ler o manual Makita DCS461, e um bom manual não só permite conhecer uma série de funcionalidades adicionais do dispositivo, mas evita a formação da maioria das falhas.

Então, o que deve conter o manual perfeito?

Primeiro, o manual Makita DCS461 deve conte:
- dados técnicos do dispositivo Makita DCS461
- nome do fabricante e ano de fabricação do dispositivo Makita DCS461
- instruções de utilização, regulação e manutenção do dispositivo Makita DCS461
- sinais de segurança e certificados que comprovam a conformidade com as normas pertinentes

Por que você não ler manuais?

Normalmente, isso é devido à falta de tempo e à certeza quanto à funcionalidade específica do dispositivo adquirido. Infelizmente, a mesma ligação e o arranque Makita DCS461 não são suficientes. O manual contém uma série de orientações sobre funcionalidades específicas, a segurança, os métodos de manutenção (mesmo sobre produtos que devem ser usados), possíveis defeitos Makita DCS461 e formas de resolver problemas comuns durante o uso. No final, no manual podemos encontrar as coordenadas do serviço Makita na ausência da eficácia das soluções propostas. Atualmente, muito apreciados são manuais na forma de animações interessantes e vídeos de instrução que de uma forma melhor do que o o folheto falam ao usuário. Este tipo de manual é a chance que o usuário percorrer todo o vídeo instrutivo, sem ignorar especificações e descrições técnicas complicadas Makita DCS461, como para a versão papel.

Por que ler manuais?

Primeiro de tudo, contem a resposta sobre a construção, as possibilidades do dispositivo Makita DCS461, uso dos acessórios individuais e uma gama de informações para desfrutar plenamente todos os recursos e facilidades.

Após a compra bem sucedida de um equipamento / dispositivo, é bom ter um momento para se familiarizar com cada parte do manual Makita DCS461. Atualmente, são cuidadosamente preparados e traduzidos para sejam não só compreensíveis para os usuários, mas para cumprir a sua função básica de informação

Índice do manual

  • Página 1

    Instruction Manual Original Instruction Manual Important: Read this instruction manual carefully before putting the chain saw into operation and strictly observe the safety regulations! Keep this instruction manual! DCS460 DCS461 DCS500 DCS501[...]

  • Página 2

    2 RE Y EU Conformity Declaration The undersigned, T amiro Kishima and Rainer Bergfeld, as authorized by DOLMAR GmbH, declare that the MAKIT A machines, T ype: EU prototype test certi Þ cate No. DCS460, 461 (178) M6T 09 10 24243 108 DCS500, 501 (179) M6T 09 10 24243 108 manufactured by DOLMAR GmbH, Jenfelder Str . 38, 22045 Hamburg, Germany , confo[...]

  • Página 3

    3 1 4 5 6 7 3 2 Delivery inventory DCS461/501 = Saw with decompression valve 1. Chain saw 2. Guide bar 3. Saw chain 4. Chain protection cover 5. Universal wrench 6. Offset screwdriver 7. Screwdriver for carburetor adjustment 8. Instruction manual (not shown) In case one of the parts listed should not be included in the delivery inventory , please c[...]

  • Página 4

    4 4 5 6 7 1 2 3 1 4 3 2 SAFETY PRECAUTIONS Intended use Power chain saws This power chain saw may be used only for sawing wood out of doors. It is intended for the followisng uses depending on its class: - Professional and mid-class: Use on small, medium and large trees: felling, limb removal, cutting to length, thinning. - Hobbyklasse: Occasional [...]

  • Página 5

    5 6 5 7 8 9 ● Maintenance ● Stopping work ● Refuelling ● T ransport ● Sharpening the chain ● Putting out of function 3 Meter Fuels / Refuelling - Stop the engine before refuelling the chain saw. - Do not smoke or work near open Þ res (5). - Let the engine cool down before refuelling. - Fuels can contain substances similar to solvents. [...]

  • Página 6

    6 10 12 13 14 11 Kickback - When working with the chain saw dangerous kickbacks may occur . - Kickback occurs when the upper part of the end of the guide bar inadvertently touches wood or other hard objects (10). - This causes the saw to be thrown back toward the user with great force and out of control. Risk of injury! In order to prevent kickback[...]

  • Página 7

    7 15 16 17 18 19 2 1 / 2 45° 45° = cutting down area - Be careful when cutting splintery wood. Cut pieces of wood may be pulled along (risk of injuries). - When cutting with the upper edge of the guide bar, the chain saw may be pushed in the direction of the user if the chain gets clamped. For this reason use the lower edge of the bar whenever po[...]

  • Página 8

    8 20 21 22 24 T ransport and storage - When changing your location during work switch off the chain saw and actuate the chain brake in order to prevent an inad- vertent start of the chain. - Never carry or transport the chain saw with the chain run- ning. - When transporting the chain saw over long distances the guide bar protection cover (delivere[...]

  • Página 9

    9 2 24 25 16 17 18 19 3 4 1 6 7 5 8 9 11 12 13 14 15 20 21 22 23 10 Stroke volume cm 3 45,6 49,9 Bore mm 43 45 Stroke mm 31,4 31,4 Max. power at speed 3) kW / 1/min 2,2 / 10,000 2,4 / 10,000 Max. torque at speed 3) Nm / 1/min 2,7 / 7,000 2,9 / 7,000 Idling speed / max. engine speed with bar and chain 1/min 2,500 / 13,800 2,500 / 13,800 Clutch engag[...]

  • Página 10

    10 5 7 6 5 4 1 2 3 C D B A Put on the guide bar ( 7 ). Make sure that the pin ( 5 ) of the chain tensioner engages in the hole in the guide bar . Remove the plastic transport cover (*) and dispose of prop- erly . Turn chain tensioning screw ( 4 ) to the left (counter-clockwise) until the pin ( 5 ) of the chain tensioner is underneath the threaded p[...]

  • Página 11

    11 8 10 1 9 9 12 2 4 F H E 2 3 G Replace the sprocket guard (3). Tighten the nuts ( 2 ) only hand-tight to begin with. Lift the chain ( 9 ) over the sprocket ( 8 ). CAUTION: Do not insert the chain between the chain sprocket and the disc. Guide the chain from above about halfway into the groove ( 10 ) on the guide bar . Place the chain over the cha[...]

  • Página 12

    12 2 4 1 2 1 C B A Engaging the chain brake (braking) If the kickback is strong enough the sudden acceleration of the guide bar combined with the inertia of the hand guard ( 1 ) will automatically actuate the chain brake. T o engage the chain brake manually , simply push the hand guard ( 1 ) forward (towards the tip of the saw) with your left hand [...]

  • Página 13

    13 E + OIL 50:1 OIL D Fuel CAUTION: This saw is powered by mineral-oil products (gasoline and oil) . Be especially careful when handling gasoline . Do not smoke. Keep tool well away from open ß ames, spark, or Þ re (explosion hazard). Fuel mixture This tool is powered by a high-performance air-cooled two-stroke engine. It runs on a mixture of gas[...]

  • Página 14

    14 A B NEVER USE W ASTE OIL Waste oil is very dangerous for the environment. Waste oil contains high amounts of carcinogenic substances. Residues in waste oil result in a high degree of wear and tear at the oil pump and the sawing device. In case of damage caused by using waste oil or unappropriate chain oil the product guarantee will be null and v[...]

  • Página 15

    15 2 3 1 C E D Checking the chain lubrication Never work with the chain saw withoute suf Þ cient chain lubri - ca tion. Otherwise the service life of the chain and guide bar will be reduced. Before starting work check the oil level in the tank and the oil feed. Check the oil feed rate as described below: Start the chain saw (see „Starting the en[...]

  • Página 16

    16 A B 1 4 5 3 2 Cold start (Choke) W arm start (ON) Engine off Combination switch in safety position (ignition current cut off, necessary for all mainte- nance, repair , and installation work) Starting the engine Do not start the chain saw until after it is completely as- sembled and checked! Move at least 3 meters / 10 feet away from the place wh[...]

  • Página 17

    17 6 C 7 8 Working in winter In order to prevent carburetor icing in conditions of low tempe- rature combined with high humidity , and below + 5°C in order to get up to operating temperature faster , heated air can be taken from the cylinder . Remove the cover (see “Cleaning the air Þ lter”). Remove the insert ( 7 ) and insert it as shown for[...]

  • Página 18

    18 H S L A CAUTION: Do not adjust the carburetor until the machine has been completely assembled and checked! Do not adjust the carburetor without a tachometer! Carburetor adjustment is necessary for optimum engine performance, for safer and more economical operation. Adjust the carburetor only with the engine warm, a clean air Þ lter, and properl[...]

  • Página 19

    19 B Adjusting the carburetor (only for not EU-countries) Carburetor adjustment is necessary for optimum engine performance, for safer and more economical operation. The engine should be warm, the air Þ lter clean, and the chain properly tensioned. Have carburetor adjustment done by an authorised MAKIT A service centre. The carburetor is factory-a[...]

  • Página 20

    20 min. 3 mm (0.11”) A B C The sharpening angle ( α ) must be identical for all cutters! 25° for chain type 686, 099 30° for chain type 086, 484 35° for chain type 093 The teeth will have the proper angle (ß) automatically if the proper round Þ le is used. 60° for chain type 686, 099 85° for chain type 086, 093, 484 Different angles resul[...]

  • Página 21

    21 1 2 D 4/5 E F Chain typ 086, 484, 686, 099 Chain typ 093 Files and how to work with them Use a special saw chain round Þ le for sharpening. Standard round Þ les are unsuitable. For the order number , see “Accessories”. T ype 086, 484, 686 : File the Þ rst cutter half with a 4,8 mm dia. round saw-chain Þ le, then switch to a 4.5 mm dia. ?[...]

  • Página 22

    22 7 2 3 1 4 6 5 A B Cleaning the brake band and sprocket interior CAUTION: Before doing any work on the guide bar or chain, always switch off the engine and pull the plug cap off the spark plug (see „Replacing the spark plug“) . Always wear protective gloves! CAUTION: Start the chain saw only after having assembled it completely and inspected.[...]

  • Página 23

    23 8 12 13 11 9 14 15 C Check the sprocket before mounting a new chain. Worn out sprockets ( 8 ) may damage the new chain and must therefore be replaced. Remove the sprocket guard (See „PUTTING INTO OPERA TI- ON“ Þ gs. B ). Remove the chain and guide bar . Remove circlip ( 9 ). CAUTION: The circlip will pop out of the groove. When removing it,[...]

  • Página 24

    24 5 3 6 4 A 1 2 5 3 4 5a CAUTION: T o prevent eye injury , always wear eye protection when cleaning the Þ lter with compressed air! Do not use fuel to clean the air Þ lter . Disengage the cover clasp ( 1 ) with the universal wrench and take off the cover ( 2 ). Push up the combination switch ( 3 ) (Choke position) to prevent dirt particles from [...]

  • Página 25

    25 8 9 7 0,5 mm 11 10 12 B C D Checking the muf ß er screws Remove the retaining plate ( 10 ) by unscrewing screws ( 11 , short) and ( 12 , long). The muf ß er screws are now accessible through the blind holes and can be checked for tight Þ t. If they are loose, hand-tighten them (Important - do not overtighten!). Replacing the spark plug CAUTIO[...]

  • Página 26

    26 A 1 2 7 8 6 5 14 13 4 4 4 9 10 12 11 3 Replacing the starter cable/ Replacing the return spring pack/Replacing the starter spring Unscrew four screws ( 1 ). Remove fan housing ( 2 ). Remove the air guide ( 3 ) from the fan housing. CAREFUL! Injury hazard! Do not unscrew screw (7) if the return spring is under tension. If the starter cable is to [...]

  • Página 27

    27 14 B 15 C Replacing the suction head The felt Þ lter ( 15 ) of the suction head can become clogged. It is recommended to replace the suction head once every three months in order to ensure unimpeded fuel ß ow to the carburetor . T o remove the suction head for replacement, pull it out through the tank Þ ller neck using a piece of wire bent at[...]

  • Página 28

    28 General Chain saw Clean exterior , check for damage. In case of damage, have repaired by a quali Þ ed service centre immediately Saw chain Sharpen regulary , replace in good time 20-12 Chain brake Have inspected regularly at an authorized service centre Guide bar Turn over to ensure even wear of bearing surfaces Replace in good time 12, 22 Star[...]

  • Página 29

    29 Service, spare parts and guarantee Maintenance and repair The maintenance and repair of modern engines as well as all safety devices require quali Þ ed technical training and a special work- shop equipped with special tools and testing devices. Any work not described in this Manual may be performed only by a MAKIT A service centre. The MAKIT A [...]

  • Página 30

    30 T rouble shooting Malfunction System Observation Cause Chain does not run Chain brake Engine runs Chain brake actuated. Engine does not start or Ignition system Ignition spark Malfunction in fuel supply system, com- only with dif Þ culty pression system, mechanical malfunction. No ignition spark Switch on ST OP , fault or short-circuit in the w[...]

  • Página 31

    31 26 33 27 28 29 30 31/32 25 21 20 5 1 2 3 14 16 12 13 4 15 17 10 11 9 18 19 8 7 6 Extract from the spare parts list Use only original MAKIT A parts. For repairs and replacement of other parts, see your MAKIT A service centre. DCS460 / DCS461 DCS500 / DCS501[...]

  • Página 32

    32 Extract from the spare parts list Use only original MAKIT A parts. For repairs and replacement of other parts, see your MAKIT A service centre. DCS460 / DCS461 DCS500 / DCS501 Pos. MAKIT A-No. Qty . Denomination 1 445 033 631 1 Sprocket nose bar .325“, 33 cm (13“) 445 038 631 1 Sprocket nose bar .325“, 38 cm (15“) 445 045 631 1 Sprocket [...]

  • Página 33

    33 Notes[...]

  • Página 34

    34 Notes[...]

  • Página 35

    35 Notes[...]

  • Página 36

    To Þ nd your local distributor , please visit www .makita-outdoor.com Form: 995 705 302 (3.10 GB) Speci Þ cations subject to change without notice MAKIT A Werkzeug GmbH Postfach 70 04 20 D-22004 Hamburg Germany[...]