Makita CORDLESS DRIVER DRILL 6222DE manual

a Capacities Steel Wood I Wood screw I Machine screw Cordless Driver Drill No load speed Dimensions Net (L x W x H) weight (RPM) Equipped with Electric Brake MODEL 6222DE MODEL 6222DWE Battery Cartridge 9120 INSTRUCTION MANUAL * Model DC9700 Fast Charger With Fast Charger 9.6 V SPEC IF I CAT1 0 N S A.C. only 50 Hz - 60 Hz D.C. 7.2 V, 9.6 V 1 Hr. * [...]

IN1 PORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMEN[...]

14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in. 16. EXTENSION CORDS. Make sure your extension cord is in good condition. When using [...]

VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user - as well as damage to the tool. If in doubt, DO NOT PLUG IN T[...]

IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGE 1. 2. 3. 4. 5. 6. 7. 8. 9. IO. 11. 12. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, 12) battery, and (3) product usin[...]

ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) 2. Do not attempt to use a step-up transformer, an engine generator or DC power 3. Do not allow anything to cover or clog the charger vents. 4. Always cover the battery terminals with the battery cover when the batte[...]

Installing or removing battery cartridge *Always switch off the tool before insertion or removal of the battery cartridge *To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge. *To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing an[...]

ASSEMBLY Installing or removing driver bit or drill bit CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the bit Hold the ring and turn the sleeve counter- clockwise to open the chuck jaws. Place the bit in the chuck as far as it will go. Hold the ring firmly and turn the sleev[...]

CAUTION: Always withdraw the tool from the workpiece before resuming operation. If the tool can- not be withdrawn, hold the tool firmly when turning on the tool, to overcome a strong reaction. Adjusting the fastening torque The fastening torque can be adjusted in six stages by turning the adjusting ring so that the pointer on the adjusting ring poi[...]

Drilling operation First, turn the adjusting ring so that the pointer on the adjusting ring points to the -.- mark- ing. Then proceed as follows. *Drilling in wood When drilling in wood, best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the bit into the workpiece. To prevent the[...]

MAINTENANCE CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Recy[...]

ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Square drill bit - Bits 784606-0A I Size I Part[...]

1 Hour Automotive charger Model DC9112 Part No. 1131 10-5 1 Hour charger Model DC1201 Part No. 113126-0 Battery cartridge 9120 Part No. 192638-6 Plastic carrying case Part No. 824447-2 High Capacity charger Model DC1410 1 Hour Automotive charger Model DC1412 Battery cover Part No. 414938-7 13[...]

Feb.-ll-'97 US CORDLESS DRIVER DRILL Model 6222D Note: The switch and other part configurations may differ from country to country. 14[...]

MODEL 6222D ITEM NO. NO. USED 21 22 23 24 25 26 21 28 29 30 31 Feb-11-'97 US 1 1 1 1 1 1 1 1 1 1 1 MACHINE ~ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1 1 7 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 1 1 - DESCRIPTION 'ALM itD DESCRlFTlON MACHINE Handle Set Wth Item 381 Name Plate Tapping Screw 4x18 Battery Holder Switch Lever Switch Lever Co[...]

MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freigh[...]