Makita 4320 manual

Jig Saw I I 174 mm 16-718") 0 - 3,200 18 mm 50 mm 6 mm (1 1/16',) 12") I1 14") MODEL 4320 1.3 kg 12.9 Ibs) INSTRUCTION MANUAL DOUBLE INSULA1 'ION SPEC IF I CAT IONS Strokes Overall I Net per minute length weight Max. cutting capacities Length of stroke Steel[...]

IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. 2. 3. 4. 5. 6. 7. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AR[...]

14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don’t carry tool with finger on switch. Be sure switch is OFF when plugging in. 16. EXTENSION CORDS. Make sure your extension cord is in good condition. When using an [...]

VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user - as well as damage to the tool. If in doubt, DO NOT PLUG IN T[...]

Installing or removing saw blade CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the blade. The blade installing position varies depending upon the type of blade being used. Install the blade in the proper position as shown in the figures below. Blade holder Blade clamp Installing position for Maki[...]

Keep the blade shank flush with the installing position so that it does not ride up on the shoulder of the blade holder. Tighten the bolt securely with the hex wrench. I Blade Correct 3lade shank rides If blade holder. Blade Nrong ; up on shoulder I I I I I I I L-J Blade holder -0 remove the blade, follow the installation procedures in reverse. Usi[...]

Switch action Tool speed is increased by increasing pres- sure on the trigger. To start the tool, simply pull the trigger. Release the trigger to stop. For continuous operation, pull the trigger and then push in the lock button. To stop the tool from the locked position, pull the trigger fully, then release it. Lock button / CAUTION : Before pluggi[...]

Loosen the bolt on the back of the base with the hex wrench and slide the base slightly backwards. Tilt the base to the de- sired angle. The edge of the housing indi- cates the bevel angle. Then check the con- tact between the back edge of the blade and the roller. Now tighten the bolt secure- ly on the back of the base. Roller Edge of housing [...]

Using guide rule (Rip fence) When cutting widths of under 150mm (6") repeatedly, use of the guide rule will assure fast, clean, straight cuts. To attach the guide rule (rip fence), secure the rule holder to the base with the screw (do not tighten). Insert the guide rule between the base and the rule holder. Now tighten the screw with the hex w[...]

To attach the circular guide, use the pin, inserting it in the center hole (arrow) and secure it with the threaded knob. Then slide the base of the tool forwards. The circular guide attaches to the base of the tool in the same manner as the guide rule (rip fence). Metal cutting Always use a suitable coolant (cutting oil) when cutting metal. Failure[...]

MA I NTENANC E CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always usin[...]

ACCESSOR I ES Blade type CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. An exception : Universal shank jig[...]

Blade type Applications Feature Wood and plywood Plartlcr Aluminum Mild steel 3 - 55 mm thick No 1 1118'' - 2-1/8"1 No 1 3 - 55 mm thick 1118" - 2-118") l- 1 5 - 6 mm thick 1 - 6 mm thick 1 - 3 mm thick A'so Ideal for Sta'nleSs Iteel -_ llllti, - 114,,1 (3164,, 114.pl (3164,, - 118.,l For corrugated plasticsand to[...]

Oec.-07-'93 US JIG SAW Model 4320 Note: The switch and other part configurations may differ from country to country. 14[...]

MODEL 4320 Dec.-07-'93 US ~ 10 11 12 13 14 15 16 'EM DESCRIPTION 'LLM DESCRIPTION 13 21 31 41 51 61 71 1 1 1 2 1 1 1 __ 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Plane Bearing 4 Slider Sleeve 4 Gear Pin 6 Switch Housing Set (With Item 281 Cord Name Plate Ball Beating 607LLB Carbon Brush Terminal Base Complete 55C Field ARMATURE ASSEM[...]

MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freigh[...]