Klegg electronic M6 501P manual

DIGIT AL DECODER[...]

1 Acknowledgement & Trademark FCC Compliance Statement The equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against h armful interference in residential installation. This equipment generates, uses, and can[...]

2 ? ? Reorient or relocate the receiving antenna. ? ? Increase the separation between the equipment and receiver. ? ? Connect the equipment into an outlet on a circuit different from that to which the recei ver is connected. ? ? Consult your dealer or an experienced radio/TV technician for help. Notice This device complies with Part 15 of the FCC r[...]

3 Table of Contents Introducti on ---------------------------------------------------------------- - 4 Checking Package Contents --------------------------------------------------- 4 M6 501P Features ----------------------------------------------------------- 5 Important Safety Instructions -------------------------------------------------- 5 Insta[...]

4 Introduction Thank you for purchasing the Klegg M6 501P Surround Sound Decoder. This versatile audio surround sound system has been precisely designed to bring you the most advanced surround modes including DTS, Dolby Digita l & Dolby Pro Logic. This system will reproduce six discrete channels of encoded sound tracks with true fidelity and so[...]

5 M6 501P Features - DTS - Dolby Digit al - Dolby Pro Logic - Bass Management - Sound Field Processing - Equalization Important Safety Instructions To ensure your safety, please read these instructions before operating this unit. 1. Note all instructions and warnings marked on the unit. 2. Always use the correct line voltage. Please refer to page 6[...]

6 Safety Voltage Chart: The following chart details the correct AC adapter for your country: Input Device Voltage Frequency Output Area AC 100 V 50 /60 Hz DC 12V, 1A Japan AC 120 V 60 Hz DC 12V, 1A North America/ Taiwan M6 501P AC 230 V 50 Hz DC 12V, 1A Europe/UK Installation ? ? Turn off any electrical or computer device that you plan to connect t[...]

7 M6 501P Front Panel 1. The POWER Button This button turns M6 501P ON or OFF. 2. The POWER Indicator Th is LED lights up when you plug in DC - 12V. 3. Speaker Configuration LEDs Each LED represents the status of an individual channel. When a particular channel is active, the LED lights up. A RED LED light means this particular channel has been set[...]

8 M6 501P Real Panel G9 L R S L S R C SW L R L R L R S/PDIF DC+12V LINE AUX 1 AUX 2 OUTPUT 2 3 4 1 5 + _ (c) M6 501P Real Panel 1. G9 Audio Output: This output feeds 6 channels audio signals; L (Front Left), R (Front Right), SL (Surround Left), SR (Surround Right), C (Center) & SW (Subwoofer) to the matching inputs on a control center or power [...]

9 Connecting M6 501P (with External Power Amplifier) G9 L R SL SR C SW L R L R L R S/PDIF DC+12V LINE AUX 1 AUX 2 OUTPUT Game Consoles Audio Out Phone Jack Audio Out Coaxial digital Output Digital Audio Out Coaxial Optical Play Rec L R L R L R L R CD player DVD Player + _ + _ + _ + _ + _ Left Surround Left Center Surround Right Right External Ampli[...]

10 Connecting M6 501P (with the Klegg M6 501R Theater System)[...]

11 1. After properly connecting M6 501P to your audio sources and amplifier, plug in M6 501P’s AC adapter to an AC outlet. 2. Activate the M6 501P power by pushing the POWER Button on the front panel. Then, turn on the power for all audio sources, amplifier, and/o r powered subwoofer. 3. Having completed the installation, get ready to experience [...]

12 M6 501P Remote Control DRC power balance delay prologic field EQ on/off EQ setup preset 1 preset 2 preset 3 save preset 4 load Cen SW VOL mute 1 2 3 4 5 6 7 8 9 10 11 12 13 14 16 17 18 19 SL/SR D Time 15 1. POWER Button On/Off key. 2. INPUT MODE Button Select from 5 different source inputs. 3. TEST Button 5.1 channel test tone activation. 4. MUT[...]

13 In the following pages we have provided detailed operation explanations to guide you thro ugh the proper setup and operation of the M6 501 P. As you might have noticed, there is only a POWER ON/OFF button on the front panel. The M6 501P has been purposely designed for user - friendly remote control operation. All functions and settings of the M6[...]

14 M6 501P Operation – LCD Display Auto Decode Mode (Auto Detect Input Stream Type) When the M6 501P is turned on it automatically detects and differentiates the audio signal coming from source unit. Playin g a DVD with Dolby Digital (AC3) encoding will display the following information: D o l b y D i g i t a l C o S U R R O U N D Playing a DVD w[...]

15 M6 501P Operation – Input Selection Input Selection power balance delay prologic field EQ on/off EQ setup preset 1 preset 2 preset 3 mute The M6 501P can be connected up to 5 audio sour ces. Select the input source feeding the M6 501P by repeatedly pressing the INPUT Button on the remote control until the desired setting is reached. In the Dig[...]

16 M6 501P Operation – Test Mode Test Mode power balance delay prologic field EQ on/off EQ setup preset 1 preset 2 preset 3 mute After completing the installation, press the TEST Button on the remote to see if the system functions properly. You can also use the test mode to test the location of the speakers. When the TEST Button is pres sed, whit[...]

17 M6 501P Operation – Mute Mode Mute Mode power balance delay prologic field EQ on/off EQ setup preset 1 preset 2 preset 3 mute Pressing MUTE Button on the remote control interrupts all signal outputs (including the G9 and 6 RCA connectors.) To disable the mute function press MUTE Button again. When the MUTE Button is pressed the M6 501P will di[...]

18 M6 501P Operation – Balance Setting Balance Balance Button DRC balance delay prologic field EQ on/off EQ setup preset 1 preset 2 preset 3 save preset 4 load Cen SW VOL SL/SR D Time Users can customize the volume setting of each individual channel. To select a channel press the BALANCE Button on the remote control. Press this button repeatedly [...]

19 M6 501P Operation – Delay Calibration SL SR R L SW TV C The ideal listening position is defined below: ? ? Center channel speaker should be placed in a position that has an equal distance as the left and right speakers to listener. ? ? Surround left and surround right speakers should be placed behind the listener and above listener’s ear lev[...]

20 M6 501P Operation – Time Delay Adjustment of Center Channel Speaker Delay Calibration DRC balance delay prologic field EQ on/off EQ setup preset 1 preset 2 preset 3 save preset 4 load Cen SW VOL SL/SR D Time Press the DELAY Button to select the length of delay time fo r SL/SR/C channels. Repeatedly pressing the DELAY Button will allow you to c[...]

21 M6 501P Operation – Time Delay Adjustment on Surround Speakers Delay Calibration DRC balance delay prologic field EQ on/off EQ setup preset 1 preset 2 preset 3 save preset 4 load Cen SW VOL SL/SR D Time Press DELAY Button to select the length of delay time for SL/S R/C channels. Repeatedly pressing the DELAY Button will allow you to select the[...]

22 M6 501P Operation – Pro Logic Mode Pro Logic Mode power balance delay prologic field EQ on/off EQ setup preset 1 preset 2 preset 3 mute Your M6 501P will automatically switch to Pro Logic mode when it detects the Pro Logic signal . With other signal inputs you can select the Dolby Pro Logic mode by press ing Prologic B utton on the remote. Rep[...]

23 M6 501P Operation – Speaker Mode with Bass Manager Speaker Mode with Bass Manager DRC save preset 4 load Cen SW VOL SL/SR D Time The six LEDs on the front panel of the M6 501P represent 6 audio channels: L, R, C, SL, SR, SW (otherwise known as 5.1). If a particular channel is active in narrow bandwidth mode the LED will light up in GR EEN. A R[...]

24 By pressing the SW B utton the subwoofer will be switched on/off and the LCD will display the following information: D o l b y D i g i t a I C o S P K S W O N D o l b y D i g i t a I C o S P K S W O F F Bass Manager By pressing the BASS MANA GER Button you can choose from three different settings of: Bass Config.1, Bass Config.2 and Bass Config.[...]

25 M6 501P Operat ion – Saving Preset s Setting Preset s DRC balance delay prologic field EQ on/off EQ setup preset 1 preset 2 preset 3 save preset 4 load Cen SW VOL mute SL/SR D Time The M6 501P allows you to customize up to 4 settings. This function allows you to program, save and load your favorite configurations at any tim e . Preset settings[...]

26 M6 501P Operation – Loading Preset Loading Preset DRC field EQ on/off EQ setup preset 1 preset 2 preset 3 save preset 4 load Cen SW VOL SL/SR D Time You can load a previously saved preset by press ing LOAD B utton on the remote. Preset 1: Press any of the 4 p reset button s, (P RESET 1, P RESET 2, P RESET 3 or P RESET 4) and the display will s[...]

27 M6 501P Operation – Sound Field Process ing DSP Sound Field field EQ on/off EQ setup preset 1 preset 2 preset 3 save preset 4 load Cen SW SL/SR The M6 501 P is equipped with a sound field processor that provides six different field effects including Disable, Hall, Theater, Sta dium , Club, and Church. By pressing the Field B utton on the remot[...]

28 M6 501P Operation – Equaliz ation 5 – Band Equaliz ation DRC balance delay prologic field EQ on/off EQ setup preset 1 preset 2 preset 3 save preset 4 load Cen SW VOL mute SL/SR D Time The M6 501P features an on board 5 - band equalizer which allows you to fine - tune the sound of your favorite movie/music. Press the EQ SETUP B utton on the r[...]

29 M6 501P Operation – DRC (Dynamic Range Compression) DRC DRC save preset 4 load Cen SW VOL SL/SR D Time The M6 501P features Dynamic Range Compression (DRC). This sophisticated technolo gy creates realistic sound fields with rich, detailed sound that is remarkably free from distortion. Repeatedly pressing DRC button will c ycle through 3 modes [...]

30 M6 501P Operation – Resetting Resetting DRC Cen SW VOL SL/SR D Time The M6 501P can be reset to its default settings by pressing the RESET Button on the remote. Pressing the RESET B utton will reset the M6 501P to its factory default settings: D o l b y D i g i t a I C o R E S E T t o F a c t o r Y When t he reset is completed the M6 501P reve[...]

31 Troubleshooting This section is designed to help you solve possible problems you might encounter. Common questions and ans wers regarding installation and connection are listed below for your reference. In case these pointers do not solve the problem please contact your dealer or Klegg Customer Enquiries for further assistance. Problem Cause Rem[...]

32 Warranty Your Klegg M6 501P Surround Sound Processor comes with a one - year warranty from the date of purchase. This warranty does not cover any incompatibilities due to the user ’ s hardware or any other related system configuration in which the M6 501P interfaces. This warranty does not cover any damage caused by negligence, non - authorize[...]