Husqvarna 966957301 manual

505 29 00-57 04.21.08 CL PRINTED IN U.S.A. OWNER/OPERA TOR MANU AL Model: CT20 / 966957301 SPECIFICA TIONS • Durable T ecumseh TC III Engine • P ositive On/Off Switch • Heavy-Duty Handlebars with Anti- Vibe Grips • Depth Control Bar • F our Heavy-Duty Removable Tines • 6’’ or 10” Cultivating Width • Tine Speed—162 RPM • W or[...]

2 SAFETY RULES AND PRECAUTIONS As with any item of power equipment it is necessary that you learn and observe ALL safety precautions. This includes the care for the machine as well as personal safety . This machine is only as dangerous as the person who is operating it. DO NOT BE CARELESS! In the beginning you will be cautious. Don't allow you[...]

3 9. Before cleaning, repairing, or inspecting, STOP THE ENGINE, make certain all moving parts have stopped, and disconnect the spark plug wire. 10. NEVER run engine indoors. Exhaust fumes contain Carbon Monoxide which is an ODORLESS and DEADL Y POISONOUS GAS. 11. NEVER operate the Tiller/Cultivator without the proper guards, plates, or other safet[...]

4 T ABLE OF CONTENTS DESCRIPTION P AGE Safety Rules and Precautions.......................................................................................................2-3 Assembly .........................................................................................................................................5-6 Pre-Operation/Starting....[...]

5 AS SEMBL Y With the exception of handlebars, controls and transport kit, your new tiller has been completely assembled at the factory . It should be noted that right and left sides are determined by the operators position behind the unit. HANDLEBARS (L OWER) (See Fig. 1) 1. Place a curved washer onto each of two (2) 1/4” x 4 1/2” hex head bol[...]

6 THROTTLE CABLE Unwind throttle cable from around engine. CAUTION: Be careful not to kink cable. ON/OFF SWITCH 1. Place 1 3/8” long slotted pan head screw into switch plate and down through hole in upper right hand handlebar . (See Fig. 2) 2. Place rubber isolator over screw underneath handlebar . Follow with throttle trigger body . 3. Place fla[...]

7 WARNING-24:1- Disregard instructions on oil containers. Do not mix directly in fuel tank. Do not use multi-viscosity oils. Use high speed air cooled 2-cycle oil . U.S Imperial Metric Gas Oil Gal. Oz. Gas Oil Gal. Oz. Gas Oil Gal. Oz. 1 5 2 10 1 6 2 12 4 166 8 322 T o start engine, place the unit in a flat, clear area. ON/OFF SWITCH ON/OFF SWITCH [...]

8 WARNING: When pulling starter rope, the rope can unexpectedly jerk back toward engine causing serious injury . T o avoid this risk, carefully follow these instructions: Move rocker switch to "I" position. 5. Grasp starter cord handle. Se Fig. 9 a. Pull rope out slowly until you feel drag. b. Without allowing the rope to retract, continu[...]

9 TINE SP ACERS The two tine spacers provided can be used to replace outside tines to narrow tilled path. DANGER! AL WA YS MOVE SWITCH TO "O" POSITION AND REMOVE SP ARK PLUG WIRE BEFORE TRYING TO REMOVE OBSTRUCTIONS. CLEAN UNIT AFTER EACH OPERA TION.* *AL WA YS CLEAN UNIT AFTER EACH OPERA TION. This includes removing any string, wire, veg[...]

10 TO CLEAN SCREEN a) Wash SCREEN in water and detergent solution. b) Rinse thoroughly in clean water , then air dry . TO CLEAN AND RE-OIL FOAM FIL TER a) Wash FOAM FIL TER in water and detergent solution and squeeze (don’t twist) until all dirt is removed. b) Rinse thoroughly in clear water . c) Wrap in a clean cloth and squeeze (don’t twist) [...]

11 4).% (5" ./4%ª(5" 0/3)4)/.ª). 2%, ! 4)/.3()0 4/ª4).%3 &2/.4 /&ª4),,%2 34/.9ª3/),ª0 ! 44%2.ªA 34/.9ª3/),ª0 ! 44%2.ªB &2/.4 /&ª4),,%2 &2/.4 /&ª4),,%2 2%'5, !2ª4).%ª0 ! 44%2.  ª ª ª      4. For regular[...]

12 IDLE SCREW NARROW CUL TIVA TING The two outer tines can be removed to give you a narrower cultivating width. This width is approximately 6". This will give you the ability to get between very closely spaced plants. In order to do this, pull the hairpin out of the hole in the outboard end of the tine shaft. Slide the tines off the tine shaft[...]

13 HANDLEBARS/GRIP/ON-OFF SWITCH/ THROTTLE CONTROL/THROTTLE CABLE ITEM ORDER NO . NO. DESCRIPTION QTY . REQ. 1 505 29 00-01 Grip, Handlebar 2 2 505 29 00-02 Screw , #10-24 x 1 3/8 1 3 505 29 00-03 Switch Assy , w/Mtg Plate 1 4 505 29 00-04 Isolator 1 5 505 29 00-05 Nut, Throttle/Switch Assy 1 6 505 29 00-06 Throttle Cable 1 7 505 29 00-07 Wire Asse[...]

14 TRANSMIS SION ASSEMBL Y ITEM ORDER NO . NO. DESCRIPTION QTY . REQ . 1 505 29 00-18 Seal 2 2 505 29 00-19 Screw , Phillips Pan Hd 1/4-20 x 1/2 2 4 505 29 00-20 Bushing, Bronze 2 5 505 29 00-21 Drum & Hub, Clutch 1 6 505 29 00-22 Bearing, Roller 1 7 505 29 00-23 Shaft, Connecting 1 8 505 29 00-24 Bushing, Bronze 2 9 505 29 00-25 Washer , Thrus[...]

15 ENGINE/TRANSMIS SION/TINES/SHIELD ITEM ORDER NO . NO . DESCRIPTION QTY . REQ. 1 – – – – – – – Engine* 1 2 505 29 00-61 Clutch Assy 1 3 505 29 00-62 Spring, Clutch 2 4 505 29 00-39 Drag Stake 1 5 505 29 00-58 Pin, Clevis 5/16 x 7/8 1 6 505 29 00-40 Hairpin 1 7 505 29 00-35 Bracket Assembly 1 8 505 29 00-41 T ransmission Assembly , C[...]

16 TRANSPORT KIT AS SEMBL Y 1. Assemble the wheel assembly and install the wheel assembly on the tiller with the arrow up as shown. T orque: 14 ft-lb (20 N-m). Fig. 20 1 HEX BOL T , 3/8-16 X 8 inch 2 INNER COLL AR (2) 3 OUTER COLL AR (2) 4 WHEEL BAR ("UP" ARROW) 5 WHEEL (2) CLEVIS PIN 7 L OCK NUT , 3/8-16 L OCK PIN 6 WASHER (2) ITEM ORDER[...]

17 NOTES[...]

18 NOTES[...]

19 NOTES[...]

SECTION 1: LIMITED W ARRANTY Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free from defects in material and workmanship from the date of purchase for the “W arranty Period” of the product as set forth below: Lifetime W arranty (Parts and Labor): All tiller tines and trimmer s[...]