Husqvarna 1130SBE manual

1130SBE Owner's Manual[...]

2 IMPORT ANT Safe Operation Practices for W alk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury . W ARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. Caution should be e[...]

3 PRODUCT SPECIFICA TIONS Gasoline Capacity 4.0 Quarts and T ype: Unleaded Regular only Oil T ype SAE 30 (above 40°F) (API SG–SL): SAE 5W-30 or 10W-30 (0° to +40°F) SAE 0W-30 (below 0°F) Oil Capacity: 26 Ounces Spark Plug: Champion RN4C (Gap: .030") CONGRA TULA TIONS on your purchase of a new snow thrower . It has been designed, engineer[...]

4 P ARTS P ACKED SEP ARA TEL Y IN CART ON[...]

5 ASSEMBL Y / PRE-OPERA TION Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower . Reading the entire manual will familiarize you with the unit, which will assist you in assembly , operation and maintenance of the product. Y our new snow thrower has been as sem bled at the factory [...]

6 ASSEMBL Y / PRE-OPERA TION AUGER CONTROL ROD CONTROL ARM RUBBER SLEEVE LOOP OPENING UP FIG. 5 INST ALL AUGER CONTROL ROD (See Figs. 5 and 6) The auger control rod has the short loop on the end of the spring as shown. 1. Slide rubber sleeve up rod and hook end of spring into control arm with loop opening up as shown. 2. With top end of rod positio[...]

7 ASSEMBL Y / PRE-OPERA TION INST ALL DISCHARGE CHUTE / CHUTE ROT A TER HEAD (See Fig. 7) NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotater head. 1. Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower . 2. Position chute rotater head over chute bracket. If [...]

8 OPERA TION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERA TING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literat[...]

9 MEETS A.N.S.I. SAFETY REQUIREMENTS Our snow throwers conform to the standards of the American National Standards Institute. FIG. 10 OPERA TION Drive speed control lever - used to select forward or reverse motion and speed of snow thrower . T raction drive control lever - used to engage power-pro- pelled for ward or reverse motion of snow thrower [...]

10 OPERA TION TO CONTROL SNOW DISCHARGE (See Fig. 14) W ARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup. W ARNING: If the discharge chute or au- [...]

11 TO MOVE FOR W ARD AND BACKW ARD (See Fig. 17) SELF-PROPELLING, forward and reverse movement of the snow thrower , is controlled by the traction drive control lever located on the left side handle. • Squeeze traction drive control lever to handle to en gage the drive system. • Release traction drive control lever to stop the forward or revers[...]

12 TO ADJUST SKID PLA TES (See Fig. 19) NOTE: The wrench provided in your parts bag may be used to adjust the skid plates. Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions. For removal of snow i[...]

13 TO ST ART ENGINE • Be sure fuel shut-off valve is in the OPEN position. Y our snow thrower engine is equipped with both a 120 V olt A.C. electric starter and a recoil starter . The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 V olt A.C. household current. • Be sure your house is a 120 V[...]

14 MAINTENANCE LUBRICA TION CHART GENERAL REC OM MEN DA TIONS The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. T o receive full value from the warranty , operator must maintain snow thrower as in struct ed in this manual. Some ad just - ments will need to be made periodically to prop[...]

15 MAINTENANCE SNOW THROWER Always observe safety rules when performing main te nance. TIRES • Maintain proper air pressure in both tires (14–17 P .S.I. / 19-24.5 N-m). • Keep tires free of gasoline / oil, which can harm rubber. NOTE: T o seal tire punctures and prevent fl at tires due to slow leaks, tire sealant may be purchased from your l[...]

16 SER VICE AND ADJUSTMENTS W ARNING: T o avoid serious injury , before performing any service or ad- just ments: 1. Be sure throttle is in STOP position. 2. Remove safety ignition key . 3. Make sure the augers and all mov ing parts have completely stopped. 4. Disconnect spark plug wire from spark plug and place wire where it can not come in contac[...]

17 SER VICE AND ADJUSTMENTS TO REPLACE BEL TS (See Fig. 24) The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear , they should be replaced. It is recommended that the belt(s) be replaced by a qualifi ed service center . NOTE: It is recommended that both the auger and traction drive belt be repl[...]

18 ST ORAGE Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more. W ARNING: Never store the snow thrower with gaso line in the tank in side a build ing where fumes may reach an open fl ame, spark or pilot light as on a fur nace, water heater , clothes dryer or gas ap pli anc[...]

19 Does not start 1. Fuel shut-off valve (if so 1. T urn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key . is not inserted. 3. Out of fuel. 3. Fill fuel tank. 4. Throttle in STOP position. 4. Move throttle to F AST position. 5. Choke in OFF position. 5. Move to FULL position. 6. [...]

20 REP AIR P ARTS AUGER HOUSING / IMPELLER ASSEMBL Y SNOW THROWER - MODEL NO. 1130SBE (96193001700), PRODUCT NO. 961 93 00-17 6 6 5 9 9 12 7 7 8 6 11 57 10 10 13 4 14 16 15 36 37 50 47 42 42 44 27 27 43 43 46 38 45 41 40 39 34 32 49 19 48 51 33 35 56 30 31 28 19 55 28 19 55 22 18 26 25 20 25 26 29 21 20 24 18 10 24 54 52 53 53 23 21 54 21 52 17 17 [...]

21 KEY P ART NO. NO. DESCRIPTION 4 532 19 10-79 Pulley , Impeller 5 532 18 89-09 Bearing Assembly , Flange 6 532 19 85-41 Nut, Hex Flange 5/16-18 7 532 18 03-55 Bolt, Flat Head, Carriage 5/16-18 x 5/8 8 872 27 05-05 Bolt, Carriage 5/16-1 8 x 5/8 9 532 19 98-79 Bolt 10 532 40 77-21 Housing, Auger 1 1 532 40 76-45 Bar , Scraper 12 532 18 40-95 Bracke[...]

22 REP AIR P ARTS CONTROL P ANEL / DISCHARGE CHUTE SNOW THROWER - MODEL NO. 1130SBE (96193001700), PRODUCT NO. 961 93 00-17 3 2 1 2 6 19 2 2 26 28 27 27 25 20 29 31 30 7 4 5 6 8 8 16 18 17 10 14 3 13 15 9 11 12 22 23 22 23[...]

23 REP AIR P ARTS CONTROL P ANEL / DISCHARGE CHUTE SNOW THROWER - MODEL NO. 1130SBE (96193001700), PRODUCT NO. 961 93 00-17 KEY P ART NO. NO. DESCRIPTION 1 532 18 33-34 Knob, Lever 2 817 50 10-10 Screw #10-24 x 5/8 3 532 19 84-75 Control Assembly , Defl ector 4 873 80 06-00 Nut, Lock 3/8-16 5 819 13 13-16 Washer , Flat 3/8 6 532 40 49-74 Control A[...]

24 REP AIR P ARTS HANDLES SNOW THROWER - MODEL NO. 1130SBE (96193001700), PRODUCT NO. 961 93 00-17 10 11 15 23 22 27 27 22 11 15 12 12 13 15 41 49 41 49 48 47 16 17 16 17 15 14 32 31 32 30 31 29 38 39 40 37 33 35 35 34 34 42 43 44 45 46 46 7 6 36 2 5 5 1 4 4 4 4 8 28 28 9 18 19 26 24 24 25 5 5 20 21[...]

25 REP AIR P ARTS HANDLES SNOW THROWER - MODEL NO. 1130SBE (96193001700), PRODUCT NO. 961 93 00-17 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your lawn mower and void your warranty . KEY P ART NO. [...]

26 REP AIR P ARTS DRIVE SNOW THROWER - MODEL NO. 1130SBE (96193001700), PRODUCT NO. 961 93 00-17 4 4 4 1 2 5 5 1 2 1 20 21 17 19 18 18 7 7 2 2 2 24 23 12 32 27 44 22 16 15 2 4 4 13 1 2 5 5 8 9 10 6 41 14 43 11 35 33 15 41 22 34 29 22 31 26 25 28 30 40 39 38 36 37 33[...]

27 KEY P ART NO. NO. DESCRIPTION 1 532 19 85-84 Screw , Hex Head 5/16-18 x 3/4 2 532 75 1 1-53 Nut, Lock 5/16-18 4 532 19 85-84 Screw , Hex Head 5/16-18 x 1/2 5 532 18 00-17 Bearing, Flange 6 532 18 01-34 Shaft, Auxiliary 7 532 17 92-70 Spacer , Plate 8 532 19 29-07 Plate, Auxiliary 9 532 18 00-82 Gear , Intermediate (12/58) 10 532 18 00-65 Gear , [...]

28 REP AIR P ARTS CHASSIS / ENGINE / PULLEYS SNOW THROWER - MODEL NO. 1130SBE (96193001700), PRODUCT NO. 961 93 00-17 6 19 17 10 21 22 23 2 1 3 4 6 7 8 9 12 13 15 27 26 25 24 18 7 20 14 47 47 48 46 44 49 50 51 52 35 55 34 33 32 38 36 41 6 37 39 42 43 11 11 44 45 41 30 29 31 31 58 16 10 21 28 57 6 11[...]

29 REP AIR P ARTS CHASSIS / ENGINE / PULLEYS SNOW THROWER - MODEL NO. 1130SBE (96193001700), PRODUCT NO. 961 93 00-17 KEY P ART NO. NO. DESCRIPTION 1 532 18 10-44 Spring, T raction Idler 2 532 18 05-22 Pulley , Idler (2-1/4) 3 - - - Engine, T ecumseh, Model Number LH358SA (For engine service and replacement parts, call T ecumseh Products at 1-800-5[...]

30 REP AIR P ARTS WHEELS / DECALS SNOW THROWER - MODEL NO. 1130SBE (96193001700), PRODUCT NO. 961 93 00-17 7 32 30 32 30 15 18 17 19 13 20 11 27 27 19 16 20 11 11 11 11 14 15 12 13 18 14 12 4 4 31 34 34 2 8 3 21 33 22 23 24 25 26 28 28 29 10 10 4 4 7 28 28 26 29 25 24 23 22 33 21 9 1 2 3 10 5 3 4 2 10 7 6 8 9 11 12 1 11 3 13[...]

31 REP AIR P ARTS WHEELS / DECALS SNOW THROWER - MODEL NO. 1130SBE (96193001700), PRODUCT NO. 961 93 00-17 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your lawn mower and void your warranty . KEY P [...]

532 40 57-35 Rev . 1 08.04.06 BY Printed in U.S.A. SECTION 1: LIMITED W ARRANTY H u s q v a rn a F o re s t & G a rd e n C o m p a n y (“H u s q v a rn a ”) w a rra n ts H u s q v a rn a p ro d u c t to th e o ri g in a l p u r - c h a s e r to b e fre e fro m d e fe c ts in m a te ria l a n d w o rk m a n s h ip fro m th e d a te o f p u r[...]