Hans Grohe 27005XX1 manual

Ra in da nc e Sh ow er pa ne l 27005XX1 Installation Instructions / W arranty[...]

2 Raindance Showerpanel 27005XX1[...]

3 T echnical Data Operating pressure: max.145 psi Recommended pressure: 30 - 60 psi T est pressure: 232 psi Max. hot water temp.: 176° F* Recommended hot water temp.: 120°F - 140°F* Flo w rate @ 45 psi Handshower 2.5 gpm Bodysprays <1 gpm each Protection against back siphonage is provided by check valves in the hot and cold supply elbows. Thi[...]

4 Preparation for Installation Install 1/2” IPS nipples for the hot and cold water supplies at the locations shown on the diagram. The nipples should extend 5/8” outside the surface of the finish wall. For proper operation of the unit, the hot supply should be on the left, and the cold supply should be on the right. Install the wall surface mat[...]

5 Installation W rap the nipples with several layers of T eflon tape. Install the elbows included with the panel. The outlets should point downwards. The elbow should extend no more than 1 1/4” from the surface of the finished wall. With a helper holding the panel in place, mark the positions of the screw holes. Set the panel aside, securely supp[...]

6 Drill the screw holes with a 6 mm bit suitable for the wall surface. Install the anchors. Seal the wall around the anchors with water- proof sealant. Hold the panel against the wall. Install the gray plastic insert. Insert the top screw through the front of the panel, the washer and the insert. Screw it into the anchor .[...]

7 Install the center and bottom screws and washers. Connect the supply hoses to the hot and cold supply elbows. Connect the supply hoses to the hot and cold inlet ports on the valve. T ur n the water on at the main. Push the diverter stem up to turn the water on to the panel. Check all connections for leaks.[...]

8 Once you ensure that the connections are water- tight, push the diverter stem down to tur n the water off to the panel. Install the side seals on the front cover . Trim off any excess. Push the front cover into place. Install the diverter sleeve. Make sure that the indexing mark on the thermostatic mixer sleeve is at the 12:00 position. Install t[...]

9 Install the diverter handle. Tighten the set screw with a 4 mm Allen wrench. Place a black rubber washer in one end of the handshower hose. Screw this end of the hose to the handshower outlet port. Place the screen washer in the other end of the hose. Screw this end of the hose to the handshower . Place the handshower in the holder . Adjust the S[...]

10 Justify the Thermostatic Mixer Handle Set the High T emperature Limit Stop (optional) T ur n the water on to the handshower . T ur n the thermostatic mixer handle until the output water measures 100 o on a ther- mometer . T urning the handle clockwise makes the water cooler , counter-clockwise makes the water warmer . T ur n the water off. Remov[...]

11 T ur n the water on to the handshower . T urn the temperature control stem until the output water is the desired maximum high temperature -- usually 110 o *. T ur n the water off. Replace the stop ring so that the tooth is against the high temperature limit stop. Replace the clip. Justify the handle. *Please know and follow all applicable local [...]

12 Using the Diverter Pull the lever upward to turn the water on. Pivot the handle to the desired function. There are five functions: Alll-around shower (handshower and 4 lower bodysprays) 4 lower bodysprays 2 upper bodysprays Full-body massage (all 6 bodysprays) Handheld shower[...]

13 Scale Removal The Raindance Air 3-jet handshower incorporates the Rubit TM cleaning system. If scale deposits are noticed in the spray channels, turn the water on lightly and rub the spray channels with a finger or a sponge. Rain AIR Balance AIR Whirl AIR Using the 3-Jet Handshower T o change spray modes, push the selector lever until the desire[...]

14 Rinse the handshower with clear water . Reinstall the handshower . T urn on the water and allow the handshower to flush for at least one minute.[...]

15 T roubleshooting Problem Possible Cause Remedy Insufficient water - Supply pressure inadequate - Filters on thermostat cartridge dirty - Screen washer dirty - Check water pressure (If a pump has been installed, check to see if the pump is working). - Clean thermostat filters - Clean screen washer between shower and hose Crossflow , hot water bei[...]

16 1 2 3 4 5 6 8 10 11 12 13 14 15 16 18 20 22 23x2 25x2 29x2,5 17 7 9 19 21 6 6[...]

17 1 handshower 28519XXX 2 slider 97024XXX 3 handshower hose, 63” 28276XXX 4 upper cover 97324000 5 escutcheon 97326000 6 body shower 28406000 7 diverter handle 10490XXX 8 thermostatic mixer handle 38391XXX 9 flange 97858XXX 10 front cover 97859000 11 sleeve 95032XXX 12 adapter for handle 97108000 13 thermostat cartridge 94282000 14 nut 96945000 [...]

18 Limited Lifetime Consumer W arranty This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996, and installed in either the United States or Canada. WHO IS COVERED BY [...]

19 including, without limitation, a commercial purpose, this warranty extends only (i) for 1 year , with respect to Hansgrohe and Commercial products, and (ii) for 5 years, with respect to AXOR products. THIS W ARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT P A Y FOR: A. Conditions, malfunctions or damage not resulting from defects in material or w[...]

Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 30004 T el. 770 360-9880 • Fax 770 360 9887 www .hansgrohe-USA.com US - Installation Instructions • Part No. 90402321 • Revised 08/2007[...]