Fujitsu AWU36CX manual

AIR CONDITIONER W ALL MOUNTED TYPE KEEP THIS MANUAL FOR FUTURE REFERENCE FUJITSU GENERAL LIMITED OPERA TING MANUAL MODE D’EMPLOI MANUAL DE FUNCIONAMIENT O P/N9373597018-02 Indoor Unit A WU36CX Outdoor Unit AOU36CX English Français Español[...]

En-1 CONTENTS SAFETY PRECAUTIONS .......................................... 1 FEA TURES AND FUNCTIONS ................................. 2 NAME OF P AR TS ...................................................... 3 PREP ARA TION .......................................................... 5 OPERA TION .....................................................[...]

En-2 FEA TURES AND FUNCTIONS AUTOMA TIC OPERA TION ● COOLING MODEL Merely press the ST ART/STOP button, and the unit will begin automatic operation in the Cooling or Dry mode as appropriate, in accordance with the thermostat setting and the actual temperature of the room. ● HEA T & COOL MODEL (REVERSE CYCLE) Merely press the ST ART/STOP but[...]

En-3 Fig. 2 Fig. 3 Fig. 4 Instructions relating to heating (*) are applicable only to “ HEA T & COOL MODEL ” (Reverse Cycle). NAME OF P AR TS Fig. 5 Fig. 6 Fig. 1 Fig. 8 Fig. 7 0 1 4 9 A B 3 76 5 8 2 C D D E[...]

En-4 Fig. 1 Indoor Unit 1 Operating Control Panel (Fig. 2) 2 MANUAL AUTO button 3 Remote Control Signal Receiver 4 Indicator Lamps (Fig. 3) 5 OPERA TION Indicator Lamp (green ...... COOL, DRY , F AN) (red .......... *HEA T) 6 TIMER Indicator Lamp (yellow) 7 SWING Indicator Lamp (orange) (VERTICAL SWING) 8 SWING Indicator Lamp (orange) (HORIZONT AL [...]

En-5 PREP ARA TION CAUTION! ● Take care to prevent infants from accidentally swallowing batteries. ● When not using the remote control unit for an extended period, remove the batteries to avoid possible leakage and damage to the unit. ● If leaking battery fluid comes in contact with your skin, eyes, or mouth, immedi- ately wash with copious a[...]

En-6 Example: When set to COOL Example: When set to 86 ° F Example: When set to AUTO T o Select Mode Operation 1 Press the ST ART/STOP button (Fig. 6 L ). The indoor unit ’ s OPERA TION indicator lamp (green or red) (Fig. 3 5 ) will light. The air conditioner will start operating. 2 Press the MASTER CONTROL button (Fig. 6 G ) to se- lect the des[...]

En-7 About Mode Operation AUTO: COOLING MODEL ● When the room temperature is 4 ° F higher than the set temperature, the mode will switch between Cooling and Drying. ● During Drying mode operation, F AN set- ting is switched to LOW gentle cooling effect, and the room fan may stop rotat- ing temporarily . ● If the mode automatically selected b[...]

En-8 T o Use the ON timer or OFF timer 1 Press the ST ART/STOP button (Fig. 6 L ) (if the unit is already operating, proceed to step 2). The indoor unit ’ s OPERA TION indicator lamp (green or red) (Fig. 3 5 ) will light. 2 Press the TIMER button (Fig. 6 J ) to select the OFF timer or ON timer operation. Each time the button is pressed the timer [...]

En-9 SLEEP TIMER OPERA TION T o Use the SLEEP timer While the air conditioner is operating or stopped, press the SLEEP button (Fig. 6 F ). Both the indoor unit ’ s OPERA TION indicator lamp (gr een or red) (Fig. 3 5 ) and the TIMER indicator lamp (yellow) (Fig. 3 6 ) will light. To Change the Timer Settings Press the SLEEP button (Fig. 6 F ) once[...]

En-10 1 2 3 4 5 ADJUSTING THE DIRECTION OF AIR CIRCULA TION Instructions relating to heating (*) are applicable only to “ HEA T & COOL MODEL ” (Reverse Cycle). V ertical (up-down) direction of airflow is adjusted by pressing the remote control unit ’ s AIR FLOW DIRECTION VERTICAL SET button. Horizontal (right-left) direction of airflow is[...]

En-11 SWING OPERA TION Begin air conditioner operation before performing this procedure. T o select V ertical airflow SWING Operation Press the AIR FLOW DIRECTION VER TICAL SWING button (Fig. 6 N ). The SWING indicator lamp (VER TICAL SWING) (Fig. 3 7 ) will light. In this mode, the UP/DOWN air direction flaps will swing automatically to direct the[...]

En-12 ● Before cleaning the air conditioner , be sure to turn it off and disconnect the power supply . ● T urn off the electrical breaker . ● Be sure the intake filter (Fig. 4 9 ) is installed securely . ● When removing and replacing the intake filters, be sure not to touch the heat exchanger , as personal injury may result. CLEANING AND CA[...]

En-13 SELECTING THE REMOTE CONTROL UNIT SIGNAL CODE When two or more air conditioners are installed in a room and the remote control unit is operating an air conditioner other than the one you wish to set, change the signal code of the remote control unit to operate only the air conditioner you wish to set (four selections possible). When two or mo[...]

En-14 TROUBLESHOOTING Instructions relating to heating (*) are applicable only to “ HEA T & COOL MODEL ” (Reverse Cycle). In the event of a malfunction (burning smell, etc.), immediately stop operation, turn off the elec- trical breaker or disconnect the power supply plug, and consult authorized service personnel. Merely turning off the uni[...]

En-15 Operation and Performance TROUBLESHOOTING Instructions relating to heating (*) are applicable only to “ HEA T & COOL MODEL ” (Reverse Cycle). Symptom Doesn ’ t operate at all: Poor Cooling (or *Heating) performance: The unit operates differently from the remote control unit ’ s setting: Signal is not received after replacing the b[...]

En-16 OPERA TING TIPS ● Should the power supply to the air conditioner be inter - rupted by a power failure, the air conditioner will restart automatically in the previously selected mode once the power is restored. ● Should a power failure occur during TIMER operation, the timer will be reset and the unit will begin (or stop) operating under t[...]