Emerson BP7251 manual

READ AND SA VE THESE INSTRUCTIONS Raphael Model No. CF2600AB01 CF2600WB01 CF2600PW01 Raphael II Model No. CF2650BC01 CF2650WB01 CF2650PW01 RAPHAEL ™ / RAPHAEL II ™ Part No. F40BP72510004 Form No. BP7251-4 ® Net Weight: 29.5 Lbs. Ceiling Fan Owner's Manual LIMITED WARRANTY What The Warranty Covers: This warranty covers the motor and the ot[...]

2 W ARNING ! WARNING: To avoid fire, shock, and serious personal injury, follow these instructions. Safety Instructions 1. Read your owner’s manual carefully and keep it for future reference. 2 . Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on [...]

1. Open carton containing your ceiling fan. Remove the top half of the styrofoam packing. Remove parts and check to see that you have received the following: a. Fan motor and shade assembly b. One motor cover c. One ceiling cover d. Five blade flanges e. One hanger ball/downrod assembly f. One hanger bracket g. One yellow lead assembly uplight h. O[...]

If your fan is to replace an existing ceiling light fixture, turn electricity off at the main fuse box at this time and remove the existing light fixture. Turning off wall switch is not sufficient. To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. All wiring must be in accordance with national[...]

5 SECTION A Assembly Instructions for Installing the CF2600 and CF2650 Ceiling Fan with the Emerson SR330 Remote Contr ol or the SW350 W all Control 1. Obtain the hanger ball/downrod assembly and remove the hanger ball by loosening the setscrew in the hanger ball until the ball falls freely down the downrod (Figure 1A). Remove the pin from the down[...]

6 11. Fold the wires from the downrod into the slot in the motor coupling (Figure 5A). Then slide the downrod down the wires and seat the downrod in the motor coupling. 12. Align the clevis pin holes in the downrod with the holes in the motor coupling. Install the clevis pin and secure with the hairpin clip. The clevis pin must go through the holes[...]

7 DOWNROD PIN HANGER BALL CEILING COVER Figure 9A 17. Screw in four 60-watt (maximum) candelabra base lamps in the housing sockets (Figure 10A). Grasp the sockets and pivot them until the lamp bulbs are even with the top of the housing as shown. This will provide the optimum lighting effect. 18. Securely attach the hanger bracket to the outlet box [...]

21. Position the receiver by passing the opening in the receiver over the hanger pipe (Figure 14A). 22. Connect the black wire from the wiring harness to the black (hot) supply wire (Figure 6A). Connect the white wire from the wiring harness to the white (neutral) supply wire. Connect the green ground wires from the hanger bracket and the hanger ba[...]

31. Using the 5/64” hex wrench (supplied), loosen the setscrew in the collar on the light kit adapter assembly. Then pass the connectors and the wires from the motor shaft through the collar (Figure 18A). Screw the adapter assembly onto the motor shaft and then tighten the setscrew to secure the adapter assembly to the motor shaft. Connect the co[...]

8. Install the setscrew (supplied) in the motor coupling and tighten using the 5/32” setscrew wrench (supplied) (Figure 3B). 9. Screw two 1” threaded studs (provided) into the motor (Figure 4B). Leave approximately 7/8” of the stud extending above the motor. Coil the wires and wire connectors around the motor coupling, then slide the motor co[...]

10. Position the ceiling cover over the downrod. Be sure the cover is oriented correctly, with the large opening at the top (Figure 5B). 11. Reinstall the hanger ball on the downrod as follows. Route the motor leads through the hanger ball and slide the hanger ball over the downrod (Figure 5B). Install the pin through the holes at the top of the do[...]

15. Carefully lift the fan and seat the hanger ball/downrod assembly on the hanger bracket that was just attached to the outlet box (Figure 9B). Be sure the groove in the ball is lined up with the tab on the hanger bracket (Figure 8B). NOTE: If you are installing a SR330 Remote Control or a SW350 Wall Control to operate the fan and light, refer to [...]

21. Attach one blade assembly to the motor hub using two 10-32 x 5/8” oval head screws (supplied) (Figure 13B). Do not tighten completely at this time. Install remaining blade assemblies in the same way. Gently snug all flange screws to the motor hub, working around the hub in a clockwise sequence. Next, securely tighten all flange screws, again [...]

14 Installation of the Decorative Suppor t Rods Assembly NOTE: The following procedures are to be performed only if you have installed the 18” or longer downrod. 1. Loosen the setscrew in the collar of the rod support assembly using the 5/64” hex wrench (supplied) and slide the support assembly over the downrod (Figure 1). 2. Verify that three [...]

15 Using Y our Ceiling Fan 1. Restore electrical power to the outlet box by turning the electricity on at the main fuse box. 2. Check the operation of the fan and lights by using the wall controls or the remote control. 3. If airflow is desired in the opposite direction, turn your fan off and wait for the blades to stop turning. Then slide the reve[...]

Printed in Taiwan 04/03 Part No. F40BP72510004 Form No BP7251-4 Repair Par ts Listing Raphael Part Numbers Raphael II Part Numbers Key Model No. Model No. Model No. Model No. Model No. Model No. N o . Description CF2600AB01 CF2600WB01 CF2600PW01 CF2650BC01 CF2650WB01 CF2650PW01 1 Hanger Bracket Assembly 760732 760732 760732 760732 760732 760732 Han[...]