Eiki EIP-1000T manual

EIP-1000T OWNER’S MANUAL EI KI INDUSTRIAL CO., L TD. A-Ke y to better communications U .S.A. EIKI International, Inc. 30251 Esperanza Rancho Santa Margarita CA 92688-2132 U .S.A. T el : 800-242-3454 (949)-457-0200 F ax : 800-457-3454 (949)-457-7878 E-Mail : usa@eiki.com Deutschland & Österreich EIKI Deutschland GmbH Am F rauw ald 12 65510 Id[...]

IMPORT ANT • For your assistance in reporting the loss or theft of your Projector , please recor d the Serial Number located on the bottom of the projector and r etain this information. • Before r ecycling the packaging, please ensure that you have checked the con- tents of the carton thoroughly against the list of “Supplied accessories” on[...]

EIP-1000T_EN_a 05.7.13, 11:47 AM 4[...]

1 Bef ore using the projector , please read this owner’ s manual carefully . Intr oduction 1. W ARRANTY This is to assure that you immediately r eceive the full benefit of the parts, service and labor warranty applicable to your purchase. 2. CONSUMER PRODUCT SAFETY A CT T o ensure that you will pr omptly receive any safety notification of inspect[...]

2 W ARNING: The cooling fan in this pr ojector continues to run for about 90 seconds after the projector enters standby mode. During normal operation, when putting the projector into standby mode always use the ST ANDBY -ON button on the projector or the ST ANDBY button on the remote contr ol. Ensure the cooling fan has stopped befor e disconnectin[...]

3 39 Using the Menu Screen Menu Selections (Adjustments) Example: Adjusting “Bright”. • This operation can also be performed by using the buttons on the projector . Press B MENU. • The “ Picture ” menu screen for the se- lected input mode is displayed. Adjustment buttons ( P / R / O / Q ) Example: “ Picture ” screen menu for INPUT 1[...]

4 Contents Preparing Introduction How to Read this Owner ’ s Ma nual ....... 3 Contents ............................................... 4 IMPORT ANT SAFEGUARDS ............... 6 Accessor ies ........................................ 10 P ar t Names and Functions ................. 11 Inserting the Batteries .......................... 14 Usable Rang[...]

5 Reference Appendix Maintenance ....................................... 47 Maintenance Indicators ...................... 48 Regarding the Lamp ........................... 50 Lamp ..................................................... 50 Caution Concerning the Lamp ............ 50 Replacing the Lamp ............................. 50 Removing and Inst[...]

6 1. Read Instructions All the safety and operating instructions should be read before the pr oduct is operated. 2. Retain Instructions The safety and operating instructions should be r etained for future refer ence. 3. Heed W arnings All warnings on the product and in the operating instructions should be adhered to. 4. Follow Instructions All oper[...]

7 15. Overloading Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fir e or electric shock. 16. Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch danger ous voltage points or short-out parts that could result in a fire or elec[...]

8 Observe the following safeguards when setting up your projector . Caution concerning the lamp unit ■ P otential hazard of glass par- ticles if lamp ruptures. In case of lamp rupture, contact your nearest EIKI A uthor ized Dealer or Service Center for replacement. See “ Replacing the Lamp ” on page 50 . Caution concerning the setup of the pr[...]

9 ■ When turning off the projector , the cooling fan runs to decrease the inter nal temper ature for a while. Unplug the pow er cord after the cool- ing f an stops. The period the cooling fan runs will vary , depending on the circumstances and the internal temperature. Caution regarding usa ge of the projector ■ When using the projector , be su[...]

10 Accessories Remote control T wo R-6 batteries (“AA” size, UM/SUM-3, HP-7 or similar) 3 RCA to 15-pin D-sub adaptor (11.8 " (30 cm)) QCNWGA075WJPZ • Owner ’ s manual (this manual) Optional accessory ■ Lamp unit AH-11201 Supplied accessories Lens cap (attached) Power cord* (1) (2) For U.S. and Canada, etc. (6 ' (1.8 m)) QACCDA0[...]

11 33 39 48 32 30 30 31 47 30 15 28 28, 48 39, 46 28, 48 39 T op View ST ANDBY -ON button For turning the power on and putting the projector into standby mode. Lamp indicator T emperature w arning indicator Adjustment buttons ( P / R / O / Q ) For selecting menu items. V olume buttons (– O / Q +) For adjusting the speaker sound level. ENTER butto[...]

12 Numbers in Z ref er to the main pages in this o wner’ s manual where the topic is e xplained. Rear View P ar t Names and Functions (Continued) Speaker Rear adjustment foot K ensington Secur ity Standard connector A C socket Connect the supplied Power cord. Intake v ent Exhaust vent 47 31 45 47 28 12 67 8 34 5 T erminals Using the Kensington Lo[...]

13 33 39 32 36 30 39 46 29 28 39 36 39 32 36 34 Numbers in Z ref er to the main pages in this o wner’ s manual where the topic is e xplained. ST ANDBY button For putting the projector into the standby mode. KEYST ONE button For entering the Keystone Correction mode. RETURN button For returning to the previous menu scr een during menu operations. [...]

14 • Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. • Insert the batteries making sure the polarities corr ectly match the m and n marks inside the battery compartment. • Batteries of different types have dif ferent properties, therefor e do not mix batteries of differ ent types. • Do [...]

15 • The signal from the r emote control can be r e- flected off a scr een for easy operation. How- ever , the ef fective distance of the signal may differ depending on the scr een material. When using the remote control • Ensur e that you do not drop, expose to mois- ture or high temperatur e. • The r emote control may malfunction under a fl[...]

16 Quic k Star t This section shows the basic oper ation (projector connecting with the video equipment). For details , see the page described below f or each step. Setup and Projection In this section, connection of the projector and the video equipment is e xplained using one e x- ample. 3. Remove the lens cap and turn the pr ojector on 2. Connec[...]

17 Select the “INPUT 3” using the INPUT button on the projector or D INPUT 3 on the remote control. 5. Select the INPUT mode • When pressing the INPUT button on the projector , input mode switches in the following order: INPUT1 INPUT2 INPUT3 INPUT4 • When using the remote control, pr ess the C INPUT 1/ C INPUT 2/ D INPUT 3/ E INPUT 4 button[...]

18 Ceiling-mount Setup ■ It is recommended that you use the optional EIKI ceiling-mount brac ket f or this installation. Before mounting the projector , contact y our nearest EIKI A uthorized Dealer or Service Center to obtain the recommended ceiling- mount brac ket (sold separ ately). ■ Inv er t the image by setting “Ceiling + F ront” in ?[...]

19 300" 200" 100" 80" 60" 261" 147" 174" 98" 87" 49" 70" 39" 52" 29" 34'10 " – 40' 4 " (10.6 m – 12.3 m) 23'3 " – 26'11 " (7.1 m – 8.2 m) 11'7 " – 13'5 " (3.5 m – 4.1 m) 9'4 " – 10'9 &qu[...]

20 Setting up the Pr ojector (Continued) 300 ⬙ (762 cm) 270 ⬙ (686 cm) 250 ⬙ (635 cm) 200 ⬙ (508 cm) 150 ⬙ (381 cm) 100 ⬙ (254 cm) 80 ⬙ (203 cm) 70 ⬙ (178 cm) 60 ⬙ (152 cm) 40 ⬙ (102 cm) 261 ⬙ (664 cm) 235 ⬙ (598 cm) 218 ⬙ (553 cm) 174 ⬙ (443 cm) 131 ⬙ (332 cm) 87 ⬙ (221 cm) 70 ⬙ (177 cm) 61 ⬙ (155 cm) 52 ⬙ (13[...]

21 When using a normal screen (4:3) and projecting 16:9 ima ge 300 ⬙ (762 cm) 270 ⬙ (686 cm) 250 ⬙ (635 cm) 200 ⬙ (508 cm) 150 ⬙ (381 cm) 100 ⬙ (254 cm) 80 ⬙ (203 cm) 70 ⬙ (178 cm) 60 ⬙ (152 cm) 40 ⬙ (102 cm) 240 ⬙ (610 cm) 216 ⬙ (549 cm) 200 ⬙ (508 cm) 160 ⬙ (406 cm) 120 ⬙ (305 cm) 80 ⬙ (203 cm) 64 ⬙ (163 cm) 56 ?[...]

22 Samples of Cab les f or Connection Cables f or a camera or a video game Equipment Input Signal Cable T erminal on the projector S-video cable (commercially av ailable) Video cable (commercially a vailab le) A udio-visual equipment Camera/ video game S-video S-video Compo- nent video Video A udio Cables f or a camera or a video game ø3.5 mm mini[...]

23 Connecting to Video Equipment Before connecting, ensure that the power cord of the pr ojector is unplugg ed fr om the AC outlet and turn off the devices to be connected. After making all connections, turn on the projector first and then the other de vices. The projector is equipped with input terminals that suppor t component, S-video , and vide[...]

24 L R T o video output terminal When connecting to equipment with video output terminal (INPUT4) T o audio output terminal Composite video cable (commercially available) RCA audio cable* (commercially available) T o AUDIO (INPUT 3, 4) terminal T o INPUT4 terminal DVD, etc. *Use the cable when you want to enjoy the sound from the projector’ s spe[...]

25 Connecting to a Computer T o RGB output ter minal T o audio output terminal * ø3.5 mm stereo or mono audio cable (commercially available) RGB Cable (commercially available) When connecting a computer , ensure that it is the last device to be turned on after all the connections are made. Ensure that you ha v e read the owner ’ s manuals of the[...]

26 T o RGB input terminal Note Connecting to a Monitor with RGB Input T erminal Y ou can displa y computer images on both the projector and a separate monitor using two sets of RGB cables . T o RGB output terminal T o INPUT 1 terminal T o OUTPUT (INPUT 1, 2) terminal RGB cable (commercially available) RGB cable (commercially available) • RGB sign[...]

27 Note Connecting to an Amplifier or Other A udio Equipment The audio input from devices connected to the A UDIO INPUT terminals on the projector can be output to audio equipment. The audio output is determined according to the selected input mode. • ø3.5 mm minijack to RCA audio cable (commer cially available) is requir ed. • Befor e connect[...]

28 T urning the Pr ojector On/Off Remove the lens cap and press o ST ANDBY-ON on the projector or f ON on the remote control. • About the Lamp Indicator The lamp indicator illuminates to indicate the status of the lamp. Red: The lamp is on. Blinking in red: The lamp is warming up or shutting down. Green: The lamp is shut down abnor - mally or the[...]

29 On-screen Display (confirmation message) 1 2 T urning the Power off (Putting the Projector into Standby Mode) Press o ST ANDBY-ON on the pro- jector or e ST ANDBY on the re- mote control, then press that but- ton again while the confirmation message is displayed, to put the projector into standb y mode. Unplug the power cor d from the A C outlet[...]

30 1 Adjusting the Focus Y ou can adjust the f ocus with the f ocus ring on the projector . Ima ge Projection Rotate the focus ring to adjust the f o- cus while watching the pr ojected image. Focus ring Adjusting the Pr ojected Image 2 Adjusting the Scr een Size Y ou can adjust the screen size using the zoom ring on the projector . Rotate the zoom [...]

31 3 Adjusting the Height The height of the projector can be ad- justed using the adjustment feet at the front and rear of the projector . When the screen is abov e the projec- tor , the projection image can be made higher by adjusting the projector . 1 2 3 • Do not apply too much pressure on the pr o- jector when the front adjustment foot comes [...]

32 Image Pr ojection (Continued) Displaying the Black Scr een and T urning off the Sound T emporarily Adjusting the V olume Press K / L on the remote control or – O / Q + on the pr ojector to adjust the vol- ume. • Pressing K /– O will lower the volume. • Pressing L / Q + will raise the volume. • When the projector is connected to externa[...]

33 0 Keystone ADJ. END Correcting T rapezoidal Distortion When the image is projected either fr om the top or from the bottom to war ds the screen at an angle, the ima g e becomes distorted trapezoidally . The function f or correcting trapezoidal distortion is called Keystone Correction. • The Keystone Correction can be adjusted up to an angle of[...]

34 Image Pr ojection (Continued) Resize Mode This function allows you to modify or customize the resize mode to enhance the input image. De- pending on the input signal, you can choose “STRETCH”, “SIDE BAR” or “CINEMA ZOOM” image. Press H RESIZE. • See page 43 for setting on menu screen. RESIZE button VIDEO • “STRETCH” is fix ed[...]

35 : Cutout area on which images cannot be pr ojected. Computer Input Signal STRETCH Output screen image Computer Image type SIDE BAR SXGA (1280 K 1024) Resolution low er than SV GA SV GA Resolution higher than SV GA 1280 K 720 4:3 aspect ratio 5:4 aspect ratio 16:9 aspect ratio SVGA (800 K 600) XGA (1024 K 768) SXGA (1280 K 960) SXGA L (1400 K 105[...]

36 Operating with the Remote Contr ol Freezing a Moving Image Press N FREEZE. • The projected image is frozen. Press N FREEZE again to return to the moving image fr om the cur- rently connected de vice. 1 2 Selecting the Picture Mode Press G PICTURE MODE. • When pressing G PICTURE MODE, the picture mode changes in the following order: Standard [...]

37 The follo wing shows the items that can be set in the projector . Menu Items “Screen adjustment (SCR-ADJ)” menu INPUT 1 (RGB)/INPUT2 (RGB) “Picture” menu Picture Picture Mode Contrast 0 0 0 0 K 7500 SCR - ADJ PRJ - ADJ Help Bright Red Blue 1 CLR Temp Bright Boost Lamp Setting Standard Bright Reset SEL./ADJ. ENTER END Picture Resize 0 SCR[...]

38 “ Projection adjustment (PRJ-ADJ) ” menu Picture Auto Search SCR - ADJ PRJ - ADJ Help Auto Sync Auto Power Off System Sound h Off On On Off SEL./ADJ. ENTER END 0 Lamp Timer(Life) 100% Speaker On RS-232C 9600 bps Fan Mode Normal Picture There is no picture or audio SCR - ADJ PRJ - ADJ Help Vertical stripes or flickering image appear Data imag[...]

39 Using the Menu Screen Menu Selections (Adjustments) Example: Adjusting “ Bright ” . • This operation can also be performed by using the buttons on the projector . Press B MENU. • The “Picture” menu screen for the se- lected input mode is displayed. Adjustment buttons ( P / R / O / Q ) Example: “ Picture ” screen menu f or INPUT 1[...]

40 Using the Menu Screen (Contin ued) Press P or R and select “Bright” to adjust. • The selected item is highlighted. • Press h ENTER again to return to the previous screen. Press O or Q to adjust the item selected. • The adjustment is stored. Press B MENU/HELP . • The menu screen will disappear . 3 4 5 0 Bright Picture SEL./ADJ. Rtn. M[...]

41 Picture Adjustment (“Picture” menu) Selectable items Standard Natural Dynamic Movie1 Movie2 Q Example: “Picture” screen menu for INPUT 1 (RGB) mode Q Example: “Picture” screen menu f or INPUT 3 mode Picture Picture Mode Contrast 0 0 0 0 K 7500 SCR - ADJ PRJ - ADJ Help Bright Color Tint 0 Sharp 1 CLR Temp Bright Boost Progressive 3D P[...]

42 4 4 4 4 4 Pr ogressive • In NTSC or P AL60Hz, even if the 3D Progr es- sive mode has been set, the three-two pull down enhancement will be enabled automati- cally when the film source has been enter ed. • When the image is blurred or noisy , switch to the optimal mode. • When using progressive inputs, inputs ar e di- rectly displayed so th[...]

43 Adjusting the Pr ojected Imag e ( “ SCR - ADJ ” men u) Picture Resize 0 SCR - ADJ PRJ - ADJ Help Keystone OSD Display Background PRJ Mode Language Front English Logo On Stretch 6 5 4 3 2 1 1 1 1 1 1 Setting the Resize Mode • For details of the Resize mode, see pages 34 and 35 . • Y ou can also press H RESIZE on the remote control to set [...]

44 Adjusting the Pr ojector Function ( “ PRJ - ADJ ” menu) Picture Auto Search SCR - ADJ PRJ - ADJ Help Auto Sync Auto Power Off System Sound h Off On On Off SEL./ADJ. ENTER END 0 Lamp Timer(Life) 100% Speaker On RS-232C 9600 bps Fan Mode Normal 1 1 1 1 1 A uto Search Function This function automatically searches for and switches to the input m[...]

45 Menu operation n P age 39 • When the Auto Power Of f function is set to “On”, 5 minutes before the pr ojector enters standby mode, the message “Enter ST ANDBY mode in X min.” will appear on the screen to indicate the remaining minutes. Selectable items On Off Description When no input signal is detected for more than 15 minutes, the pr[...]

46 T r oubleshooting with “Help” menu Utilizing “Help” menu functions This function advises you to solve the problems during usage. • Y ou can adjust the items with check marks ( ✔ ). • The items in the “Help” menu change, de- pending on the input signal or setting that you have selected. • If the problem is not solved, refer to[...]

47 Cleaning the lens ■ Use a commercially available blower or lens cleaning paper (for glasses and camera lenses) for cleaning the lens. Do not use any liquid type cleaning agents, as they may wear off the coating film on the surface of the lens. ■ As the surface of the lens can easily get damaged, be sure not to scrape or hit the lens. Cleanin[...]

48 Maintenance Indicator s About the lamp indicator ■ When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp” will be displayed on the screen. When the per centage becomes 0%, it will change to (red), the lamp will automatically turn off and then the projector will automatically enter standby mode. At this time, the la[...]

49 • If the temperature warning indicator illuminates, and the projector enters standby mode, follow the possible solutions above and then wait until the projector has cooled down completely befor e plug- ging in the power cord and turning the power back on. (At least 10 minutes.) • If the power is turned off for a brief moment due to power out[...]

50 Regar ding the Lamp Lamp ■ It is recommended that the lamp (sold separately) be r eplaced when the remaining lamp life becomes 5% or less, or when you notice a significant deterioration in the pictur e and color quality . The lamp life (percentage) can be checked with the on-scr een display . (see page 45 ) ■ Purchase a r eplacement lamp of [...]

51 Removing and Installing the Lamp Unit • Make sure that you r emove the lamp unit by the handle. Do not touch the glass surface of the lamp unit or the inside of the projector . • T o avoid injury to yourself and damage to the lamp, be sure to car efully follow the steps below . • Do not loosen other scr ews except for the lamp unit cover a[...]

52 Regar ding the Lamp (Contin ued) Remove the lamp unit. • Loosen the securing scr ews from the lamp unit. Hold the lamp unit by the handle and pull it in the direction of the arrow . At this time, keep the lamp unit horizontal and do not tilt it. Resetting the Lamp Timer Reset the lamp timer after replacing the lamp . Insert the new lamp unit. [...]

53 Connecting Pin Assignments COMPUTER-RGB Input/Output COMPUTER-RGB/COMPONENT INPUT1, 2 and COMPUTER-RGB/COMPONENT OUTPUT Terminals: 15-pin Mini D-sub female connector 1. Video input (red) 2. Video input (green/sync on gr een) 3. Video input (blue) 4. Not connected 5. Not connected 6. Earth (red) 7. Earth (green/sync on green) 8. Earth (blue) 9. N[...]

54 DTV • When this projector r eceives 640 K 350 VESA format VGA signals, “640 K 400” appears on the screen. Computer Computer Compatibility Chart • Multiple signal support Horizontal Frequency: 15-70 kHz, V ertical Frequency: 45-85 Hz, Pixel Clock: 12-108 MHz Sync signal: Compatible with TTL level • Compatible with sync on gr een signal [...]

55 T roub leshooting No picture and no sound or projector does not start. Sound is heard but no picture appears (or pictur e is dark). Color is faded or poor . Picture is blurred; noise appears. Picture appears but no sound is heard. An unusual sound is occasionally hear d from the cabinet. Maintenance indicator on the projector illuminates or blin[...]

56 Problem Picture is gr een on INPUT 1 (Component)/ INPUT 2 (Component). Picture is pink (no green) on INPUT 1 (RGB)/INPUT 2 (RGB). Picture flickers on INPUT 1 (RGB)/INPUT 2 (RGB). Picture is too bright and whitish. The cooling fan becomes noisy . The lamp does not light up even after the projector turns on. The lamp suddenly turns off during proj[...]

57 Specifications Projector EIP-1000T NTSC3.58/NTSC4.43/P AL/P AL-M/P AL-N/P AL-60/SECAM/DTV480 I /DTV480P/ DTV540P/DTV576 I /DTV576P/DTV720P/DTV1035 I /DTV1080 I /DTV1080 I -50 Single Chip Digital Micromirror De vice TM (DMD TM ) by T exas Instruments P anel size: 0.53 " , 1chip DMD No . of dots: 409,920 dots (854 [H] × 480 [V]) 1–1.15 × [...]

58 Dimensions Units: inches (mm) M4 M4 M4 M4 12 13 / 32 ( 315) 3 1 / 16 ( 77.5) 2 19 / 32 ( 65.5) 1 53 / 64 ( 46.2) 3 5 / 32 ( 80) 1 55 / 64 ( 47) 2 7 / 8 ( 73) 2 61 / 64 ( 75) 1 11 / 32 ( 33.8) 4 19 / 64 ( 109) 4 9 / 64 ( 105) 1 7 / 8 ( 47.5) 4 7 / 64 ( 104) 7 / 16 ( 11) 11 1 / 32 ( 280) 23 / 64 ( 9) 13 / 64 ( 5) 7 / 16 ( 11) EIP-1000T_EN_m 05.7.1[...]

59 AC socket ....................................................... 28 Accessories ................................................... 10 Adjustment buttons ........................................ 39 Adjust horizontal noise ........................... 38, 46 Adjust vertical noise ............................... 38, 46 Aspect ratio ...............[...]

59 AC socket ....................................................... 28 Accessories ................................................... 10 Adjustment buttons ........................................ 39 Adjust horizontal noise ........................... 38, 46 Adjust vertical noise ............................... 38, 46 Aspect ratio ...............[...]

EIP-1000T OWNER’S MANUAL EIKI INDUSTRIAL CO., L TD. A-Ke y to better communications U .S.A. EIKI International, Inc. 30251 Esperanza Rancho Santa Margarita CA 92688-2132 U .S.A. T el : 800-242-3454 (949)-457-0200 F ax : 800-457-3454 (949)-457-7878 E-Mail : usa@eiki.com Deutschland & Österreich EIKI Deutschland GmbH Am F rauwald 12 65510 Idst[...]