Craftsman 315.11461 manual

Operator's Manual 3/8 in., 18 VOLT CORDLESS DRILL-DRIVER Variable Speed / Reversible Model No. 315.114610 Save this manual for future reference _, CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Estates, I[...]

• Warranty ......................................................................................................................................................................... 2 • Introduction ....................................................................................................................................................[...]

• w Your drill-driver has many features for making your drilling operations more pleasant and enjoyable. Safety, performance and dependability have been given top priority in the design of this drill-driver making it easy to maintain and operate. _, CAUTION: Carefully read through this entire operator's manual before using your new drill-dri[...]

• Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edges are less likely to bind and are easier to control. • Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool's operation. If damaged, have the tool serviced before[...]

_. WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. • Never usea battery that has been dropped or received a sharp blow. A damaged battery is subject to explosion. Properly dispose of a dropped battery immediately. Fail- ure to heed t[...]

Important: Some ofthe following symbols may be used onyour tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow youto operate the tool better andsafer. SYMBOL NAME DESIGNATION/EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) min Minutes Time Alternating Current Type o[...]

DRILL-DRIVER 315.114610 Maximum Torque 337 in.lb. Chuck 3/8 in. Keyiess CHARGER Item No. 9 11379 Motor DC Motor 18 Volt (1426161 ) Gear Train Two Speed Rating 120 V, 60 Hz, AC only No Load Speed 0-350/min. (Low) Charging Voltage 18 Volt 0-1300/min (High) Charge Rate 3-6 Hours Clutch 24 Positions BATTERY PACK Item No. 9 11378 (1323620) KNOW YOUR DRI[...]

TWO-SPEED LEVEL GEARTRAIN (HI-LO) KEYLESS CHUCK TORQUE ADJUSTMENT RING SWITCH TRIGGER SCREWDRIVER BITS DIRECTION OF ROTATION SELECTOR (FORWARD/REVERSE) BIT STORAGE REAR VIEW BATTERY PACK SHOWN IN CHARGING STAND CHARGER BATTERY PAq SHOWNINTOOL WRIST STRAP Fig. I 8[...]

,_ WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. _ WARNING: Do not allow familiarity with drill- your driver to make you careless. Remember that a careless fraction of a second is sufficient to [...]

SWITCH See Figure 2. To turn your drill ON, depress the switch trigger. To turn it OFF, release the switch trigger. FORWARD/REVERSE SELECTOR VARIABLE SPEED SWITCH TRIGGER Fig. 2 VARIABLE SPEED This toot has a variable speed switch that delivers higher speed and torque with increased trigger pressure. Speed is controlled by the amount of switch trig[...]

SWITCH LOCK See Figure 5. The switch trigger can be locked in the OFF position. This feature can be used to prevent the possibility of accidental starting when not in use. To lock switch trigger, place the direction of rotation selector (Forward/Reverse Selector) in center position. Note: When selector is in center position, switch trigger is locke[...]

INSTALLING BITS See Figure 7. • Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 5. • Open or close chuck jaws to a point where the open- ing is slightly larger than the bit size you intend to use. Also, raise the front of your drill slightly to keep the bit from falling out of the chuck jaws.[...]

BIT STORAGE See Figure 10. When not in use, bits provided with your drill can be placed in the storage area located on the bottom of your drill as shown in Figure 10. SCREWDRIVER BIT DRILLING See Figure 12. LEVEL I IL r_ i f=,...,...=...=.-= STORAGE AREA Fig. 10 _IL WARNING: Always wear safety goggles or safety glasses with side shields when operat[...]

CHUCK REMOVAL See Figures 13, 14, and 15. The chuck must be removed in order to use some accessories. To remove: • Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 5. • Insert a 5/16 in. or larger hex key into the chuck of your drill and tighten the chuck jaws securely. • Tap the hex key sha[...]

_ WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other part may create a hazard or cause product damage. Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil,[...]

[...]

CRAFTSMAN 3/8 in., 18 VOLT CORDLESS DRILL-DRIVER - MODEL NO. 315.114610 .=======, l SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS 2 4 3 Key Part No. Number 1 6613401 2 6903330 3 *Item No. 9 11378 4 *Item No. 9 11379 5 3073009 983000-341 PARTS LIST Description Quan. Screw (Special) ....................................................................[...]

Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door o[...]